Wide Measurement Range Metal Tube Rotameter Flowmeter Metal Tube Float Rotameter

Metal tube rotameters are widely used in pe-
troleum, chemical, power generation, pharma-
ceutical, food, water treatment, etc. Complex,
harsh environmental conditions, and a variety
of media conditions in the process of flow
measurement.
Range ratio:10:1(Special type 20:1)
Accuracy class:2.5(Special type 1.5% or 1.0%)
Working pressure:?DN15~DN50 PN16MPa (Special type 25MPa).
DN80~DN150 PN10MPa (Special type 16MPa).
Pressure rating of jacket 1.6MPa.
Output:4~20mA/?HART?/RS485?/Alarm?/Pulse
Connection mode:Flange Thread Tri-clamp

The float of the metal rotameter is in the measuring tube. With the change of flow, the float moves up, and the buoyancy of the float and the gravity of the float reach a balance at a certain position. At this time, the flow annulus area between the float and the orifice plate (or cone tube) remains constant. The area of the annular gap is proportional to the rising height of the float, that is, the rising position of the float in the measuring tube represents the flow rate, and the position of the changing float is transmitted by the internal magnet to the external indicator, so that the indicator can correctly indicate the flow value at this time. . This makes the indicator housing not in direct contact with the measuring tube, so even if a limit switch or transmitter is installed, the instrument can be used under high temperature and high pressure working conditions. It is a variable area flow measuring instrument commonly used in industrial automation process control. It has the characteristics of small size, large detection range and convenient use. It can be used to measure the flow of liquid, gas and steam, especially suitable for medium flow measurement with low flow rate and small flow.

Variable area flow meter Series are used for measure instantaneous and accumulated flow rate of liquid, gas and steam in closed pipelines. It is suitable for metering flow value on site or electronic remote. The measuring principle is based on the hydrodynamic effects,This makes float moving from bottom to top in vertical Pipe. As the displacement of float is in related to flow rate, which can be read from the indicator by means of the magnetic drive system in non-contact form . Also, flowmeters output electrical signal (4-20)mA / hart communication protocol with high / low limit Warning switches/integrating flow PCB broad can be configured.
Range ratio: 10:1(Special type 20:1).
Accuracy class: 2.5(Special type 1.5% or 1.0%).
Working pressure: DN15~DN50 PN16 (Special type 2.5MPa).
Medium temperature: Normalized type -80¡æ~+220¡æ.
Ambient temperature: -40¡æ~+120¡æ(Remote display without LCD¡Ü85¡æ).

The metal tube high temperature rotameter flowmeter has the advantage of small volume and convenient operation.It is a kind of variable area flow quantity measuring instrument.Ithas various such as field indication type,intelligent remote transmission type,corrosionresistan type,clamped type and damping type.lt can measure the flow of the media with small flow velocity and small flow quantiy.
Range ratio:10:1(Special type 20:1)
Accuracy class:2.5(Special type 1.5% or 1.0%)
Working pressure:?DN15~DN50 PN16MPa (Special type 25MPa).
DN80~DN150 PN10MPa (Special type 16MPa).?Pressure rating of jacket 1.6MPa.
Output:4~20mA/?HART?/RS485?/Alarm?/Pulse
Connection mode:Flange Thread Tri-clamp

The metal tube rotameter is a variable area flow meter based on the float position measurement, which is especially suitable for the measurement of gas and liquid flow with low flow rate and small flow. The metal tube float adopts an all-metal structure and a Modular concept design. It has the characteristics of small volume, small pressure loss, large range ratio, and convenient installation and maintenance. Therefore, it is widely used in complex and harsh environments in various industries. Flow measurement and process control for harsh media conditions.

Metal pipe flowmeter consists of measuring pipe, float, indicator and process connection components with the characteristics of small size, wide measuring range, easy installation. In the industry area, it is widely used to measure flow of gas, liquid, and steam, especially suitable for mediums with low current velocity and low flow?rate.
Range ratio:10:1(Special type 20:1)
Accuracy class:2.5(Special type 1.5% or 1.0%)
Working pressure:?DN15~DN50 PN16MPa (Special type 25MPa).
DN80~DN150 PN10MPa (Special type 16MPa).
Pressure rating of jacket 1.6MPa.
Output:4~20mA/?HART?/RS485?/Alarm?/Pulse
Connection mode:Flange Thread Tri-clamp

Metal tube rotameter is an instrument for measuring the flow of liquids or gases in pipelines. It is composed of two major parts:sensor and indicator.The sensor mainly consists of the joint flange, cone, float as well as upper and lower guiders; while, the indicator mainly consists of the casing, magnetic transmission system, dial scale and electric transmission system.
Range ratio:10:1(Special type 20:1)
Accuracy class:2.5(Special type 1.5% or 1.0%)
Working pressure:?DN15~DN50 PN16MPa (Special type 25MPa).
DN80~DN150 PN10MPa (Special type 16MPa).
Pressure rating of jacket 1.6MPa.
Output:4~20mA/?HART?/RS485?/Alarm?/Pulse
Connection mode:Flange Thread Tri-clamp

A rotameter is an industrial flowmeter used to measure the flowrate of liquids and gases. The rotameter consists of a tube and float. The float response to flowrate changes is linear, and a 10-to-1 flow range or turndown is standard. In the case of OMEGA? laboratory rotameters, far greater flexability is possible through the use of correlation equations. The rotameter is popular because it has a linear scale, a relatively long measurement range, and low pressure drop. It is simple to install and maintain.
Range ratio: 10:1(Special type 20:1).
Accuracy class: 2.5(Special type 1.5% or 1.0%).
Working pressure: DN15~DN50 PN16 (Special type 2.5MPa).
Medium temperature: Normalized type -80¡æ~+220¡æ.
Ambient temperature: -40¡æ~+120¡æ(Remote display without LCD¡Ü85¡æ).

Metal tube rotameter with the transmitter is also called digital rotameter. All-metal structure, there are indicator type, electric remote transmission type, corrosion-resistant type, high voltage type, jacket type, explosion-proof type.
Electric remote transmission, explosion-proof design. Explosion-proof mark Exd ¢ò CT6. Optional HART protocol function. DC24V power supply, the on-site pointer indicates instantaneous flow. Digital display instantaneous and cumulative flow. Two-wire system 4¡«20mA output. There are 4 buttons on the panel to view and modify internal parameters.

Metal tube float flowmeter is based on the float position measuring a variable area flow meter, adopts full metal structure, the concept of Modular design, because of its small size small pressure loss, large range than (10:1), installation, maintenance is convenient wait for acharacteristic
Range ratio:10:1(Special type 20:1)
Accuracy class:2.5(Special type 1.5% or 1.0%)
Working pressure:?DN15~DN50 PN16MPa (Special type 25MPa).
DN80~DN150 PN10MPa (Special type 16MPa).?Pressure rating of jacket 1.6MPa.
Output:4~20mA/?HART?/RS485?/Alarm?/Pulse
Connection mode:Flange Thread Tri-clamp

rotameters measure flow rate of a liquid or gas by relating linear displacement of an internal ¡°float¡± or sharp-edged orifice tube to a corresponding flow rate. Variable Area meters either allow flow through a peripheral orifice formed between a tapered wall and a float as in the traditional rotameter, or an annular orifice and an internal tapered metering pin in the Device Head. The attributes of the Variable Area flow meter are a linear relationship between flow rate, pressure differential and piston displacement. Flow rate is read on the Variable Area meters in both Analog or Digital Display by aligning the position of the piston/float to an adjacent calibrated scale.

Metal tube rotameter is a variable area flow meter based on float position measurement. Adopting all-metal structure and Modular conceptual design, it is widely used in flow measurement and process control under complex and harsh environment in various industries, with small volume, small pressure loss, large range ratio (10:1), convenient installation and maintenance, etc.
Range ratio:10:1(Special type 20:1)
Accuracy class:2.5(Special type 1.5% or 1.0%)
Working pressure:?DN15~DN50 PN16MPa (Special type 25MPa).
DN80~DN150 PN10MPa (Special type 16MPa).?Pressure rating of jacket 1.6MPa.
Output:4~20mA/?HART?/RS485?/Alarm?/Pulse
Connection mode:Flange Thread Tri-clamp

Variable Are Meters are an excellent all stainless steel Inline Flow Meter suitable for many liquids with its wide flow range from 2 lt/min up to 650 lt/min. The robust construction, pressure rating and suitability for corrosive applications makes this quality meter an excellent choice for many process applications that require flow indication.
Range ratio: 10:1(Special type 20:1).
Accuracy class: 2.5(Special type 1.5% or 1.0%).
Working pressure: DN15~DN50 PN16 (Special type 2.5MPa).
Medium temperature: Normalized type -80¡æ~+220¡æ.
Ambient temperature: -40¡æ~+120¡æ(Remote display without LCD¡Ü85¡æ).

Q&T series metal tube rotameter is applicable for the measurement and control and the flow of various fluids in gas or liquid state. Different types of rotameters can be selected for different working conditions such as high temperature, corrosive medium, different flow directions, hazardous enviroment and etc.
Range ratio:10:1(Special type 20:1)
Accuracy class:2.5(Special type 1.5% or 1.0%)
Working pressure:?DN15~DN50 PN16MPa (Special type 25MPa).
DN80~DN150 PN10MPa (Special type 16MPa).?Pressure rating of jacket 1.6MPa.
Output:4~20mA/?HART?/RS485?/Alarm?/Pulse
Connection mode:Flange Thread Tri-clamp

The remote type metal tube rotameter can be used in flow measurement and process control in complex, harsh environments and various medium conditions, and is suitable for measuring liquids and gases. Especially suitable for small diameter and low flow rate medium flow measurement; widely used in: chemical industry, power generation, food, water treatment, etc. In the process of flow measurement in complex, harsh environmental conditions, and various medium conditions.

Metal rotameter according to the explosion-proof requirements, they
can be divided into three types: common type, intrinsically safe type and isolated explosion-proof type.
Range ratio:10:1(Special type 20:1)
Accuracy class:2.5(Special type 1.5% or 1.0%)
Working pressure:?DN15~DN50 PN16MPa (Special type 25MPa).
DN80~DN150 PN10MPa (Special type 16MPa).
Pressure rating of jacket 1.6MPa.
Output:4~20mA/?HART?/RS485?/Alarm?/Pulse
Connection mode:Flange Thread Tri-clamp

Metal tube rotameter is suitable for high temperature, high pressure and strong corrosive medium; It can be used in inflammable and explosive dangerous places,for medium with small diameter and low velocity within DN200
Range ratio:10:1(Special type 20:1)
Accuracy class:2.5(Special type 1.5% or 1.0%)
Working pressure:?DN15~DN50 PN16MPa (Special type 25MPa).
DN80~DN150 PN10MPa (Special type 16MPa).?
Pressure rating of jacket 1.6MPa.
Output:4~20mA/?HART?/RS485?/Alarm?/Pulse
Connection mode:Flange Thread Tri-clamp

Metal rotameter is a variable area flow measurement instrument commonly used in industrial automation process control. It has the characteristics of small size, large detection range and convenient use. It can be used to measure the flow of liquid, gas and steam. It is especially suitable for medium flow measurement with low flow rate and small flow.

Rotameter adopts the international advanced Honeywell non-contact magnetic sensor for detecting the change of magnetic field angle, and is equipped with Motorola micro-processing system, which can realize the functions of liquid crystal indication, accumulation, remote transmission (4 ~ 20mA), pulse output, upper and lower limit alarm output, etc.
Range ratio:10:1(Special type 20:1)
Accuracy class:2.5(Special type 1.5% or 1.0%)
Working pressure:?DN15~DN50 PN16MPa (Special type 25MPa).
DN80~DN150 PN10MPa (Special type 16MPa).?Pressure rating of jacket 1.6MPa.
Output:4~20mA/?HART?/RS485?/Alarm?/Pulse
Connection mode:Flange Thread Tri-clamp

metal rotameter mainly used in liquid, acid ,or gas flow measurement and automatic control system in the oil, chemical, pharmaceutical, food and other industries.
Range ratio:10:1(Special type 20:1)
Accuracy class:2.5(Special type 1.5% or 1.0%)
Working pressure:?DN15~DN50 PN16MPa (Special type 25MPa).
DN80~DN150 PN10MPa (Special type 16MPa).
Pressure rating of jacket 1.6MPa.
Output:4~20mA/?HART?/RS485?/Alarm?/Pulse
Connection mode:Flange Thread Tri-clamp

Metal Tube Rotameter is a flow meter measuring the instantaneous and
cumulative flow of fluid (liquid, gas and steam) through a closed pipe.
It uses the dynamic action of the fluid to make the float move up in the
vertical installation of the measuring tube. The displacement of the float
is proportional to the size of the flow. Through the magnetic drive system,
the float displacement is transferred to the indicator directly indicating the
size of the flow in a non-contact manner. It can also offer 4-20 mA, HART,
low and high alarm with an extra flow PCB installed.
Range ratio: 10:1(Special type 20:1).
Accuracy class: 2.5(Special type 1.5% or 1.0%).
Working pressure: DN15~DN50 PN16 (Special type 2.5MPa).
Medium temperature: Normalized type -80¡æ~+220¡æ.
Ambient temperature: -40¡æ~+120¡æ(Remote display without LCD¡Ü85¡æ).

Matel tube flowmeter based on the float principle are versatile and can be used for conductive and non-conducting liquids and gases. The sturdy all-metal design ensures high resistance to pressure, temperature and media and stands up to extreme application and environmental conditions.
Range ratio:10:1(Special type 20:1)
Accuracy class:2.5(Special type 1.5% or 1.0%)
Working pressure:?DN15~DN50 PN16MPa (Special type 25MPa).
DN80~DN150 PN10MPa (Special type 16MPa).
Pressure rating of jacket 1.6MPa.
Output:4~20mA/?HART?/RS485?/Alarm?/Pulse
Connection mode:Flange Thread Tri-clamp

large range ratio (10:1), convenient installation and maintenance, it is
widely used in flow measurement and process control of small flow rate,
low flow rate and various harsh medium conditions in various industries
and harsh environments
Range ratio:10:1(Special type 20:1)
Accuracy class:2.5(Special type 1.5% or 1.0%)
Working pressure:?DN15~DN50 PN16MPa (Special type 25MPa).
DN80~DN150 PN10MPa (Special type 16MPa).
Pressure rating of jacket 1.6MPa.
Output:4~20mA/?HART?/RS485?/Alarm?/Pulse
Connection mode:Flange Thread Tri-clamp

variable- area flowmeter with metallic measuring tube has the characteristics of simplicity£¬relability, wide
application field, high precision and easy installation. Compared variable-area flowmeter with glass tube flow meter,
this series has the characteristics of high pressure safe, high temperature safe, easy reading etc.
It is widely applicable in petrol, chemical, power supply£¬pharmacy£¬food, water treatment industry etc.
Range ratio: 10:1(Special type 20:1).
Accuracy class: 2.5(Special type 1.5% or 1.0%).
Working pressure: DN15~DN50 PN16 (Special type 2.5MPa).
Medium temperature: Normalized type -80¡æ~+220¡æ.
Ambient temperature: -40¡æ~+120¡æ(Remote display without LCD¡Ü85¡æ).

liquid and gas metal tube float rotameter consists of measuring pipe, float, indicator and process connection components with the characteristics of small size, wide measuring range, easy installation. In the industry area, it is widely used to measure flow of gas, liquid, and steam, especially suitable for mediums with low current velocity and low flow rate
Range ratio:10:1(Special type 20:1)
Accuracy class:2.5(Special type 1.5% or 1.0%)
Working pressure:?DN15~DN50 PN16MPa (Special type 25MPa).
DN80~DN150 PN10MPa (Special type 16MPa).
Pressure rating of jacket 1.6MPa.
Output:4~20mA/?HART?/RS485?/Alarm?/Pulse
Connection mode:Flange Thread Tri-clamp

metal tube rotameter is a kind of measuring meter in which the flow rate is
changing along with the area and is widely used in the process control of industrial automation.
It has the merit of lttle volume, broad measuring range, and convenience for use. It can be used to measure liquid, gas, and vapor flow especially fits for the flow rate measurement of low flow velocity and little flow rate.
Range ratio: 10:1(Special type 20:1).
Accuracy class: 2.5(Special type 1.5% or 1.0%).
Working pressure: DN15~DN50 PN16 (Special type 2.5MPa).
Medium temperature: Normalized type -80¡æ~+220¡æ.
Ambient temperature: -40¡æ~+120¡æ(Remote display without LCD¡Ü85¡æ).

The metal tube rotameter adopts 304/316 stainless steel structure, which can be used to measure the flow of liquid, gas, and steam. It is especially suitable for low measurement of low flow rate, micro flow range, high temperature, high ressure, corrosive, conductive or non-conductive medium.
Range ratio:10:1(Special type 20:1)
Accuracy class:2.5(Special type 1.5% or 1.0%)
Working pressure:?DN15~DN50 PN16MPa (Special type 25MPa).
DN80~DN150 PN10MPa (Special type 16MPa).?Pressure rating of jacket 1.6MPa.
Output:4~20mA/?HART?/RS485?/Alarm?/Pulse
Connection mode:Flange Thread Tri-clamp

Metal tube rotameter is all metal structure design, short stroke, easy to install. Metal tube rotameter HART intelligent indicator adopts foreign signal acquisition and processing chip, modular design, without any transmission mechanism transmitter, no magnetic lag; metal tube rotameter and rotameter have data recovery, data backup, failure Electrical protection and error self-diagnosis function, parameter configuration and on-site adjustment can be carried out through the HART communication hand-held communicator. HF metal tube rotameter and rotameter are sturdy, simple, and have a long service life. They are used in the measurement and process control of liquid, gas, and steam media in petroleum, chemical, metallurgy, electric power, medicine, food, paper and other industries.

Metal tube float flowmeter, also known as the ¡°metal tube rotameter¡±, is a measuring instrument commonly used in the industrial automation process management to measure the variable area flow. Being featured with characteristics of small size, wide application range, convenient usage, etc., it is designed for measuring the flows of liquids, gases and steam, especially applicable for measurement of low flow speed and small flow rate.
Range ratio:10:1(Special type 20:1)
Accuracy class:2.5(Special type 1.5% or 1.0%)
Working pressure:?DN15~DN50 PN16MPa (Special type 25MPa).
DN80~DN150 PN10MPa (Special type 16MPa).?Pressure rating of jacket 1.6MPa.
Output:4~20mA/?HART?/RS485?/Alarm?/Pulse
Connection mode:Flange Thread Tri-clamp

The Metal Tube Rotameter uses the variable area measurement principle. The intelligent metal tube float flowmeter has a local display type and an intelligent remote transmission type, with the transmitter. Metal Tube Rotameter can be used to measure the flow of liquid, gas, and steam. It is especially suitable for medium flow measurement with a low flow rate and small flow.
Range ratio: 10:1(Special type 20:1).
Accuracy class: 2.5(Special type 1.5% or 1.0%).
Working pressure: DN15~DN50 PN16 (Special type 2.5MPa).
Medium temperature: Normalized type -80¡æ~+220¡æ.
Ambient temperature: -40¡æ~+120¡æ(Remote display without LCD¡Ü85¡æ).