Water flow sensors high quality ultrasonic drinking water flowmeters

QT621 is a portable transit-time ultrasonic flow meter with advanced functions. Portable ultrasonic flow meter includes matched precision transducers and signal processing circuitry to accurately measure the flow of most liquids. With 4-20mA and RS485 communication available, QT621 support quickly verify the flow reading of another meter and to data log flow system values over an extended time period.

Size: 1¡å~48¡å(25mm~1200mm)
Flow Range:¡À0.01 m/s~ ¡À12 m/s
Accuracy: ¡À1%
Repeatability: 0.2%
Output: 4-20mA, RS485
Power supply: Internal lithium 3000mAh
Transducer: IP68

clamp on ultrasonic portable liquid flow meter is controlled by a micro-processor system which contains a wide range of data that enables it to be used with pipes with an outside diameter ranging from 15mm up to 1200mm (depending on model) and constructed of almost any material. instrument will also operate over a wide range of fluid temperatures.

The Q&T solar power ultrasonic water flow meter that is designed for open channel flow metering, whether you have a flume, weir or any other primary device. This meter has 4-20mA, RS485 and relay output, which is a good choice for different needs of channel flow monitoring.

Analogue?Output: 4-20mA,?corresponding?to?instantaneous?flow
Relays?Output: Standard?2?relay?outputs(Optional?up?to?6?relays)
Serial?Communication: RS485,?MODBUS?-RTU?standard?protocol
Ambient?Temperature: -40 ~70 Degree C
Measure?Cycle: 1?second?(selectable?2?seconds?)
Power?Supply: DC24V?(+5%)?0.2A;?AC220V?(+20%)?0.1A?;Optional?DC12V

The Q&T solar power Open channel flow meter using transit-time principle, it is an economical ultrasonic flowmeter specifically designed for open channel. Compared with other ultrasonic flow meters on the market, it has the characteristics of high reaction rate, low power consumption and high certainty. At the same time, with non-contact level sensor, it also have the feature of installation simple easy to use, non need water supply shutdown etc.

Specifications:
Display: Backlight?LCD
Flow?Rate?Range: 0.0000~99999L/S?or?m3/h
The?maximum?of Accumulative Flow: 9999999.9?m3/h
Accuracy?of?Change in Level: 1mm?or?0.2%?of?full?span?(whichever?is?greater)
Resolution: 1mm
Analogue?Output: 4-20mA,?corresponding?to?instantaneous?flow
Relays?Output: Standard?2?relay?outputs(Optional?up?to?6?relays)
Serial?Communication: RS485,?MODBUS?-RTU?standard?protocol

Transmitter and transducer install seperately.Transmitter can install at indoor,Instrument cabinet,Dashboard.

Ultrasonic Flow meter for applications in clean water and in low conductivity media. Operating principle based on
transit time measurement.
Bi-directional flow measurement over a wide dynamic range.
Applications with conductive or non-conductive liquids for many industrial
No moving parts, no wear, no pressure loss,Maintenance-free

Q&T Wall mounted ultrasonic flowmeter clamp on type transducer is a high precision no-cut tube measurement method. This special design includes matching sensors for ease of use and is ideal for installation in existing systems Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring single clean liquids Power supply: 24VDC/85VAC-2265AC Storage: SD card optional Heat meter optional

Drinking water flowmeter ultrasonic clamp on type flowmeter is a portable liquid flow measurement device with a sensor. This Drinking water flowmeter ultrasonic clamp on type flowmeter proven transit-time ultrasonic measurement technology for superior accuracy and ease of installation and installation. This easy-to-use flowmeter comes in a rugged, waterproof carrying case for easy transport of the display, sensor, and cables between measurement locations. High accuracy +/-1.0% of FS Transducer temperature: -30~90¡ãC/-30¡ãC~160¡ãC Measuring clean liquids Battery-powered,for 12 hours Communication: RS232

DN150 ultrasonic flow meter IP67 with clamp on transducers is a portable liquid flow measurement device with a sensor. DN150 ultrasonic flow meter IP67 with clamp on transducers proven transit-time ultrasonic measurement technology for superior accuracy and ease of installation and installation. This easy-to-use flowmeter comes in a rugged, waterproof carrying case for easy transport of the display, sensor, and cables between measurement locations. High accuracy +/-1.0% of FS Transducer temperature: -30~90¡ãC/-30¡ãC~160¡ãC Measuring clean liquids Battery-powered,for 12 hours Communication: RS232

Ultrasonic clamp-on flow meter is simple to install and is suitable for large diameter pipes requiring monitoring and flow measurement, as well as a wide network of smaller supply lines. Ultrasonic clamp-on flow meter provide the tools needed to meet the diverse requirements of such a demanding industry. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring clean liquids Power supply: 24VDC/85VAC-2265AC Communication: RS485

Liquid portable ultrasonic flowmeter clamp on type 3.6V battery powered can be easily installed, removed and transported. This flowmeter makes them ideal for industrial applications that are already operational or only require occasional flow measurement. In the latter case, the user can use the same clamp on flowmeter to measure flow in multiple locations by unloading and transporting the device for each measurement Measuring accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring clean liquids Built-in rechargeable battery 3.6V Communication: RS232

Ultrasonic flow meter with RS232 communication for clean liquid is a non-contact instrument, which can measure the flow of medium with large diameter and can also be used for the measurement of medium that is not easy to contact and observe. Its measurement accuracy is very high, and the external clip-type installation can reach the highest accuracy of ¡À1.0%. It is almost not disturbed by various parameters of the measured medium, especially it can solve the strong corrosiveness, non-conductivity, Flow measurement of radioactive and flammable and explosive media. Measuring accuracy: +/-1.0% of FS Transducer temperature: -30~90¡ãC/-30¡ãC~160¡ãC Measuring clean liquids Battery-powered,for 12 hours Communication: RS232

Flange ultrasonic flow meter is one kind of contact flow metera and it is time difference meters that use ultrasonic technology to measure the velocity of an acoustically conductive liquid moving through it.
Q&T brand ultrasonic flow meter is one kind of economy type flow meter for liquid,multi channle inline ultrasonic flow meter can reach 0.5% accuracy.

Flange connect ultrasonic flow meter mainly measure various of pure liquid,such as:Clean water,Sea water,Dringking water,River water,Alcohol etc.
Signal channel type ultrasonic flow meter accuracy it better than 1.0%
Multi-channel type ultrasonic flow meter accuracy can reach 0.5%
Accuracy:¡À1.0%
Single channel or multi channel
2 way input
Heat measurement
Bi-directional flow measurement
Remote type and integral type

Inline ultrasonic flow meter support single channel and multi-channel at the same time,when one of channel is abnormal or not connected,it can automatically switch to single channel to working
Ultrasonic flow measurement according to the ¡°differential transit time¡± method: This method uses two sensors, set opposite each other in the measuring tube. Each sensor can alternately transmit and receive ultrasonic signals, while simultaneously measuring the signal transit time.

Ultrasonic clamp-on flow meter water flowmeter flow rate sensor cheap ultrasonic flow meter is a portable liquid flow measurement device with a sensor. This Ultrasonic clamp-on flow meter water flowmeter flow rate sensor cheap ultrasonic flow meter proven transit-time ultrasonic measurement technology for superior accuracy and ease of installation and installation. This easy-to-use flowmeter comes in a rugged, waterproof carrying case for easy transport of the display, sensor, and cables between measurement locations. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring single clean liquids Power supply: 24VDC/85VAC-2265AC Storage: SD card optional Heat meter optional

This river flow meter can directly display the instant and accumulative flow. This Open Channel Water Meter is based on the flow rate-water level calculation method, and adopts an advanced flow rate measuring instrument and water level measuring instrument to ensure a new intelligent high quality flow system.

Specifications:
Sensor?Level?Range: 0-4.0m; other?level?range?also?available
Blind?zone: 0.20m
Temperature?Compensation: Integral?in?probe
Pressure?Rating: 0.2MPa
Beam?Angle: 8*?(3db)
Cable?Length: 10m?standard?(can?be?extended?to?1000m)
Sensor?Material: ABS,?PVC?or?PTFE?(optional)
Sensor?Protection Class: IP68
Output: 4-20mA, Relays, RS485

Ultrasonic Flow meter for applications in clean water and in low conductivity media. Operating principle based on transit time measurement.
Pipe material:Steel,Stainless steel,Cast iron,PVC,Cement pipe and allow pipe with lining
High Isolation voltage,Strong anti-interference,Suppress voltage noise,Good isolation performance
Inline ultrasonic flow meter collect temperature signal and accuracy reach 0.001¡æ
When using inline ultrasonic flow meter to measure,allowing pipe with liner

Q&T Open Channel flow meter measures level, flow rate and total volume of water flowing through weirs, flumes and channels. The flow meters use a non-contact level sensor. Application field£º
1. Water and sewage treatment£ºpump room, collection well, biochemical reaction
tank, sedimentation tank.
2. Electricity, mines£ºmortar pool, coal slurry pool, butter storage tank, stockyard
or some mobile equipment control, etc.
3. Food industry£ºwineries, granaries, storage tanks for food materials, etc.

Specifications:
Display: Backlight?LCD
The?maximum?of Accumulative Flow: 9999999.9?m3/h
Resolution: 1mm
Analogue?Output: 4-20mA
Relays?Output: Standard?2?relay?outputs(Optional?up?to?6?relays)
Serial?Communication: RS485,?MODBUS RTU
Ambient?Temperature: -40 ~70 Degree C
Power?Supply: DC24V, AC 220V£»Optional?DC12V

Portable handheld digital ultrasonic flowmeters, clamp-on sensors to measure liquid flow. Installation process is very simple, all Chinese human-machine interface, more easy to operate. Particularly suitable flow balance testing and flow monitoring: drinking water, river water, sea water, cooling water, hot water, industrial waste water, lubricating oil, diesel oil, fuel oil, chemical liquids. Accuracy: +/-1.0% of FS Wide range: DN300mm-DN6000mm Measuring clean liquids Built-in rechargeable battery 3.6V 2000 lines storage Communication: RS232

This ultrasonic water flow meter can directly display the instant and accumulative flow. This open channel ultrasonic flow meter is based on the flow rate-water level calculation method, and adopts an advanced flow rate measuring instrument and water level measuring instrument to ensure a new intelligent flow system.

Specifications:
Sensor?Level?Range: 0-4.0m; other?level?range?also?available
Blind?zone: 0.20m
Temperature?Compensation: Integral?in?probe
Pressure?Rating: 0.2MPa
Beam?Angle: 8*?(3db)
Cable?Length: 10m?standard?(can?be?extended?to?1000m)
Sensor?Material: ABS,?PVC?or?PTFE?(optional)
Sensor?Protection Class: IP68
Output: 4-20mA, Relays, RS485

Fixed type ultrasonic clamp on flow meter adopts the self-development measurement technology.This measurement technique is a faster and more accurate process time measurement algorithm. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring single clean liquids Power supply: 24VDC/85VAC-2265AC Communication: RS485

QT811 external clamp on type ultrasonic energy meters suitable for various liquids and compatible with various pipeline materials and sizes.
Specially external clamp design, QT811 clamp on ultrasonic energy BTU meter could
measure the flow without touch the measurement liquid.
Compared with other traditional type flow meters, QT811 clamp on flow meters could achieve no pressure loss save the cost
of time and labor costs.

Pipe Size:?DN15-DN40mm (1/2¡±~1 1/2¡±)
Flow Range:¡À0.1m/s ~¡À5m/s
Temperature: 0~75¡æ (standard)
Output: 4-20mA, OCT Pulse, RS485
Accuracy:?¡À1% of measured value
Power Supply: DC10-24V

Wall Mounted ultrasonic water flow meter is an ultrasonic flowmeter used to measure the flow rate of liquids in closed pipes. The transducer is a non-contact, clamp-on type, which will provide the benefits of contamination-free operation and ease of installation. The transit time flowmeter employs two transducers, which act as ultrasonic transmitters and receivers. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring clean liquids Power supply: 24VDC/85VAC-2265AC Communication: RS485

Q&T PLCM Open Channel flow meter is CE Certificated Open Channel Flowmeter, RS485 River Flow Meter Open Channel; The cable length between probe and host up to 1000m; This PLCM ultrasonic flow meters are perfect for wastewater applications.
The probe with leak-proof structure and IP68 protect grade.
Display: Backlight LCD
The maximum of Accumulative Flow: 9999999.9 m3/h
Accuracy of Change in Level: 1mm or 0.2% of full span (whichever is greater)
Resolution: 1mm
Analogue Output: 4-20mA, corresponding to instantaneous flow
Relays Output: Standard 2 relay outputs(Optional up to 6 relays)
Serial Communication: RS485, MODBUS -RTU standard protocol
Ambient Temperature: -40 ~70 Degree C
Power Supply: DC24V (+5%) 0.2A; AC220V (+20%) 0.1A ;Optional DC12V

QT811 external clamp on ultraonic flow meter is an easy operation instrument for non-invasive, quick flow and energy measurement with clamp-on technology for many types of pipings.QT811 clamp on flow meter support user to monitor the flow rate reading directly on the device. With various kinds of outputs signals, could send the information to PLC,
central control room and etc.

Pipe Size:?DN15-DN40mm (1/2¡±~1 1/2¡±)
Flow Range:¡À0.1m/s ~¡À5m/s
Temperature: 0~75¡æ (standard)
Output: 4-20mA, OCT Pulse, RS485
Accuracy:?¡À1% of measured value
Power Supply: DC10-24V

Q&T brand ultrasonic flow meter is real flow calibrated,5 flow velocity point and calibrate 3 times for each flow velocity point.Q&T calibration device can calibrate from DN3~DN3000mm,and adopt Seimens,Rosemount,E+H brand flow meter as the standard meter.
Single channel ultrasonic flow meter accuracy <1.0% Multi-channel ultrasonic flow meter caccuracy can reach 0.5% Body material:Standard carbon steel,SS304 and SS316 are optional Power supply:DC24V and AC220V Connection way:Flange type Media temperature :-30~+150¡æ

The fluid can smothly through the inline ultrasonic flow sensors which no moving pasts,No wear,No pressure loss and Maintenance free.
Pipeline ultraosnic flow meter directly contact the liquid and make the measuring accuracy better than clamp on ultrasonic flowmeter.And installation easy,don’t need calculate the sensor installation distance and cover the coupling agent in the pipe,so this meter can collect the signal very well.
Power supply:DC24V and AC220V
Connection way:Flange type
Media temperature :-30~+150¡æ

Ultrasonic flowmeter wall mounted water flow meter Modbus RS485 communication measure flow by propagating ultrasonic waves into a liquid-filled pipe. Ultrasonic flowmeter wall mounted water flow meter Modbus RS485 communication are located outside the pipeline and offer a wide range of pipeline sizes with no pressure loss, no contact with the liquid inside, and no moving parts. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm None cut down pipe Power supply: 24VDC/85VAC-2265AC Communication: RS485

Wall Mounted Clamp on ultrasonic flowmeter proven transit-time ultrasonic measurement technology This technology can be used for permanent installations where intrusive flow meters are not economically viable for permanent installations on large pipelines and for all the different process fluids encountered in the network. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring clean liquids Power supply: 24VDC/85VAC-2265AC Communication: RS485