Water Flow Meter Turbine Flowmeter for Liquid Methanol Diesel Gasoline Petrol Beer Milk

QTWG series gas turbine meters offer high quality natural gas measurement which could increase efficiency in gas transmission, distribution and industrial applications. Turbine gas meters are wIth built in temperature and pressure compensation ensure accurate measurment in standard conditions.

Size:DN25-400mm
Material:Aluminum alloy or stainless steel
Dual Power:3.6V battery powered+DC24V
Output:4-20mA,Pulse,RS485
Accuracy:1.5% or 1.0%

turbine flowmeter Calibration of the device is carried out in laboratory conditions on the water.
If the device is supposed to be used in a viscous medium (2-300 cSt, centistokes), liquids with properties similar to those of the working medium are taken for calibration.
As a result, for each purpose and medium its own K-factor is assigned. Sometimes, manufacturers add ready-made universal viscosity charts for calibration to its equipment kit. Using them, a user can quickly determine already calculated K-factor for different substances.

turbine flowmeter is widely used in low flow rate and low viscosity Liquid measurement. Converting sensor signals into smart signal outputs through a microcomputer
processor design.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%;
OUTPUT: PULSE+4-20mA;
Digital Communication:RS485, MODBUS; HART

Turbine Flow Meter is a main type of Impeller Flowmeter also including the Anemoscope and Water meter. it is made up of Sensor and Conversion-Show. The Sensor reacts to the average velocity of fluid with multi-blades rotor so as to speculating the flow value and the accumulative flow value. The velocity (or circles) of rotor can be picked up by the way of mechanism, electromagnetic induction, photo electricity, before displaying and transmitting the records by reading device.

QTWG series turbine gas meters are designed to measure natural gas, LPG, air, carbon dioxide and non-corrosive gases. Turbine gas meters deliver high accuracy in gas flow measurements, with built-in volume corrector, integrated temperature and pressure measurement.

Size:DN25-400mm
Material:Aluminum alloy or stainless steel
Dual Power:3.6V battery powered+DC24V
Output:4-20mA,Pulse,RS485
Accuracy:1.5% or 1.0%

turbine flow meter is a volumetric metering the meter consists of a rotor and bearing assembly Suspended on a shaft, which is mounted to a support device.
This assembly is mounted inside a housing of a calibrated internal diameter. As fluid passes through the flow meter housing, the rotor will spin at a rate proportional to the volume of liquid passing through the housing. A magnetic or modulated pick-off sensor is used to detect the passage of each rotor blade and generate a frequency output. The frequency output can be read directly with the end users electronics or further processed to convert to a linear analog flow Rate output.

preprocess applications.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%/¡À0.2%;
OUTPUT: PULSE/4-20mA;
Digital Communication:RS485, MODBUS; HART

QTWG series gas turbine meters offer high quality natural gas measurement which could increase efficiency in gas transmission, distribution and industrial applications. Turbine gas meters are wIth built in temperature and pressure compensation ensure accurate measurment in standard conditions. The turbine meters are designed to accurately measure natural gas, air, nitrogen, carbon dioxide, propane vapor, and other non-corrosive gases for large volume commercial and industrial uses.

Size:DN25-400mm
Material:Aluminum alloy or stainless steel
Dual Power:3.6V battery powered+DC24V
Output:4-20mA,Pulse,RS485
Accuracy:1.5% or 1.0%

QTWG turbine gas flow meters are suitable for a wide range of markets, including natural gas, LPG and other gas industries. Q&T turbine gas meters could achieve high-precision custody transfer metering, the measurements can be automatically pressure and temperature compensated to obtain volumetric measurements in standard units.
Size:DN25-400mm
Material:Aluminum alloy or stainless steel
Dual Power:3.6V battery powered+DC24V
Output:4-20mA,Pulse,RS485
Accuracy:1.5% or 1.0%

Turbine flowmeter measures the flowrate from the number of revolutions of a blade placed in the flow. The speed of revolutions of the blade with an axis parallel to the flow direction is proportional to the speed of the flow. Utilizing the capability of highly accurate measurement for wide range of viscosity, the turbine flowmeter is useful for process control, transactions as well as process control of petroleum products, general chemical fluids, liquefied gas, water, etc.
In addition to the model for liquid, models dedicated to saturated steam measurement are also available.

turbine flow meter having a mechanical section combined with electronic board displaying the flow rate, the end connection of which is finished with a flange. Because its driving part is mechanical, it can be applied for all fluids of low temperature to high temperature with relatively high accuracy and excellent reproducibility.

turbine flow meter having a mechanical section combined with electronic board displaying the flow rate, the end connection of which is finished with a flange. Because its driving part is mechanical, it can be applied for all fluids of low temperature to high temperature with relatively high accuracy and excellent reproducibility.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%/¡À0.2%;
OUTPUT: PULSE/4-20mA;
Digital Communication:RS485, MODBUS; HART

A turbine flowmeter is a flowmeter that uses a turbine for measurement. It first converts the flow rate to the speed of the turbine. And then converts the speed into an electrical signal that is proportional to the flow. Turbine flow meter is used to detect the instantaneous flow and the total accumulated flow. And its output signal is frequency, which is easy to digitize.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%;
OUTPUT: PULSE+4-20mA;
Digital Communication:RS485, MODBUS; HART

Turbine flowmeter is a precision flow measuring instrument, which can be used to measure the flow and total amount of liquid when matched with the corresponding flow totalizer. Used in conjunction with our company’s quantitative controller, it can perform high-precision quantitative control of liquid feeding. Widely used in metering and control systems in petroleum, chemical, metallurgy, scientific research and other fields
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%/¡À0.2%;
OUTPUT: PULSE/4-20mA;
Digital Communication:RS485, MODBUS; HART

Turbine flowmeter installation
Normally turbine flow meter has flange, thread, clamp-on connections, and the fluids direction should be the same as the arrow on the meter body. The liquid turbine flow sensor can be installed horizontally and vertically, and the fluid direction must be upward when installed vertically. The liquid should be filled with tubing and must be free of air bubbles. The inner wall of the straight pipe section should be smooth and clean, free of defects such as dents, scale and peeling.

Turbine flowmeter is based on the principle of torque balance and is a speed type flow meter. It has a simple structure, light weight, high precision, good repeatability etc. It is an ideal instrument for flow measurement and energy saving.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%;
OUTPUT: PULSE+4-20mA;
Digital Communication:RS485, MODBUS; HART

turbine flow meters are used for the precise measurement of instantaneous flow rates of low-viscosity fluids such as tap and demineralized water, fuels, liquefied gases, light fuel oils, solvents, and pharmaceutical fluids. Turbine flowmeters measure volumetric flow, where fluid passing through the meter body is measured by the mean velocity of the flowing fluid media. Flow rectifiers ensure a laminar flow in the axial direction of the wheel. A low-mass turbine wheel carried concentrically within the meter body is rotated by the fluid. The RPM of the turbine wheel is directly proportional to the mean flow rate within the meter body and directly corresponds to the volumetric flow over a wide range.

turbine flow meter is available in a wide range of body sizes and styles to suit liquid flow applications for low to medium viscosity fluids.
The principle of operation is based on a permanent magnet contained within a pick-off coil on the body and a ferritic stainless steel rotor which revolves when flow is present. A small AC voltage is generated in the coil as the rotor tip passes the magnet. The frequency of this AC voltage is directly proportional to the flow rate. The total number of pulses produced represents the total flow passed through the meter.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%/¡À0.2%;
OUTPUT: PULSE/4-20mA;
Digital Communication:RS485, MODBUS; HART

The turbine flow meter accuracy plays an important role in the floating measurement process of the rotor. So the high-precision turbine flowmeter has almost no resistance during the floating measurement process of the rotor, thereby ensuring the high precision, linearity and durability of the turbine flowmeter.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%/¡À0.2%;
OUTPUT: PULSE/4-20mA;
Digital Communication:RS485, MODBUS; HART

Turbine Flowmeters draw the leading technology integrating with advanced design to produce the new generation of turbine flowmeter with the features of simple structure, light weight, high accuracy, good repeatability, flexible reaction, convenient installation/maintenance/application etc.. It is widely applied to measuring the liquid of which kinematic viscosity is under 5*10-6©O/s and have no impurify of fibre,grain etc.,and no corrosive interaction with the stainless steel 1Cr18Ni9Ti,2Cr13,and A12O3, and hard alloy in seal pipes
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%;
OUTPUT: PULSE+4-20mA;
Digital Communication:RS485, MODBUS; HART
LCD display

liquid turbine flow meter is a new type of intelligent instrument with integrated turbine flow sensor and display product calculation developed by advanced ultra-low power single-chip microcomputer technology, which has obvious advantages such as compact mechanism, clear reading, high reliability, undisturbed by external power supply, lightning resistance and low cost.

Turbine gas meter is a popular device for gas-fired, gas pipeline network and city gas field etc. With the features of high quality and low pressure loss, QTWG gas turbine meters are widely exported to more than 50+ countries.
Size:DN25-400mm
Material:Aluminum alloy or stainless steel
Dual Power:3.6V battery powered+DC24V
Output:4-20mA,Pulse,RS485
Accuracy:1.5% or 1.0%

liquid turbine flow meter is a new generation turbine flow meter which was designed with advanced flow technologies both home and aboard. The product possesses advantages of simple structure, light in weight, high accuracy, good repeatability, short response time, easy installation, etc. It could be used widely in measurement of closed pipe system for pure liquid that will not react with 1Cr18Ni9Ti, 2Cr13, Al2O3 and hard alloys.

Turbine flow meters measure the velocity of liquids, gases and cryogenic fluids. Typical fluids and gases measured with turbine flowmeters include hydrocarbons, chemicals, water, cryogenic liquids, air, natural gas and industrial gases.Apure turbine flowmeters are easy to operate and maintain. For this reason, Apure turbine flowmeters can be used worldwide and are considered a reliable, cost-effective way to achieve high-precision flow measurements
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%/¡À0.2%;
OUTPUT: PULSE/4-20mA;
Digital Communication:RS485, MODBUS; HART

liquid turbine flow meter adapts to measure the liquid rate and total flowrate of low viscosity. It can be widely used in the fields of Petrol, Chemical industry, Metallurgy, for measuring or control.
Turbine flowmeter sensors are typically located external to the flowing stream to avoid material of construction constraints that would result if wetted sensors were used. When the fluid moves faster, more pulses are generated. The transmitter processes the pulse signal to determine the flow of the fluid. Transmitters and sensing systems are available to sense flow in both the forward and reverse flow directions.

Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%/¡À0.2%;
OUTPUT: PULSE/4-20mA;
Digital Communication:RS485, MODBUS; HART

Turbine flow meters are mechanical meters that have a freely rotating turbine set in the path of a fluid stream. The flowing liquid or gas causes the turbine to spin upon its axis. The rate of spin will be proportional to the velocity of the flow. Turbine flow meters are simple and reliable. They are able to measure high flow rates with low-pressure loss. Though versatile, turbine meters do best in applications with constant conditions in liquids such as water or lower viscosity fluids.

A turbine flow meter is a volume sensing device. As liquid or gas passes through the turbine housing, it causes the freely suspended turbine blades to rotate. The velocity of the turbine rotor is directly proportional to the velocity of the fluid passing through the flow meter.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%;
OUTPUT: PULSE+4-20mA;
Digital Communication:RS485, MODBUS; HART

Gas turbine flow meter is a new generation of flow measurement device for clean gas, including natural gas, LPG gas etc. Normally LPG gas flow meter need to be with temperature and pressure compensation so that to make sure high accuracy.
Size:DN25-400mm
Material:Aluminum alloy or stainless steel
Dual Power:3.6V battery powered+DC24V
Output:4-20mA,Pulse,RS485
Accuracy:1.5%/1.0%

QTWG turbine gas flow meters are ideal flow measurement device for clean gas, including natural gas, LPG gas etc. Turbine gas meters are with lightweight in compact body and support a wide range of measurement including maximum working pressure and maximum measuring flow rate.
Size:DN25-400mm
Material:Aluminum alloy or stainless steel
Dual Power:3.6V battery powered+DC24V
Output:4-20mA,Pulse,RS485
Accuracy:1.5% or 1.0%

Turbine flowmeter is a kind of velocity flowmeter, mainly used to measure liquid flow. It uses a multi-blade rotor (turbine) to sense the average flow rate of the fluid, thereby deriving the flow or total meter. It consists of a sensor and an intelligent display, and can also be made into an integral type. Because of its high precision and repeatability It is not only widely used in the measurement of clean water flow in source water and water supply systems, but also in petroleum, organic liquids, inorganic liquids, liquefied gas, natural gas and It is also widely used in measurement objects such as cryogenic fluids
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%/¡À0.2%;
OUTPUT: PULSE/4-20mA;
Digital Communication:RS485, MODBUS; HART

liquid turbine flow meter, is a precision flow measuring instrument,that can be used to measure the flow and total volume of liquids. The structure is explosion-proof and can show the total flow, instantaneous flow and percentage of flow fullness. It is widely used in measurement and control systems in petroleum, chemical, metallurgical, scientific research and other fields. Sensors equipped with sanitary fittings can be used in the pharmaceutical industry.