Ultrasonic water flowmeter for liquid ultrasonic flow meter

Wall mounted ultrasonic flowmeter has two pcs of clamp on transducer which don’t contact the liquid media directly.The transducers emit the sould waves which can detemine the velocity of the liquid media in the pipe,flow transmitter will calculate the flowrate according to the singles.
Accuracy:±1.0%
Output:4-20mA,RS485
Transducer temperature:-40~80℃
Transducer protect:IP68
Power supply:24VDC
SD card is optional

Inline ultrasonic flow meter support single channel and multi-channel at the same time,when one of channel is abnormal or not connected,it can automatically switch to single channel to working
Ultrasonic flow measurement according to the ¡°differential transit time¡± method: This method uses two sensors, set opposite each other in the measuring tube. Each sensor can alternately transmit and receive ultrasonic signals, while simultaneously measuring the signal transit time.

QT621 ultrasonic flow meter is a type of portable flow meter, which support easily moved and installed in different pipes and convenient to carry site to site. The innovative design includes matched precision transducers
and signal processing circuitry to accurately measure the flow of most liquids over a wide range of velocities.

Size: 1¡å~48¡å(25mm~1200mm)
Flow Range:¡À0.01 m/s~ ¡À12 m/s
Accuracy: ¡À1%
Repeatability: 0.2%
Output: 4-20mA, RS485
Power supply: Internal lithium 3000mAh
Transducer: IP68

This Solar power GPRS Open Channel Flow Meter can be used for continuous measuring of municipal rain-water, wastewater, sewage discharge and irrigation water pipelines. This Open Channel flow meter measures level, flow rate and total volume of water flowing through weirs, flumes, and channels etc.

Specifications:
Display: Backlight?LCD
Flow?Rate?Range: 0.0000~99999L/S?or?m3/h
The?maximum?of Accumulative Flow: 9999999.9?m3/h
Accuracy?of?Change in Level: 1mm?or?0.2%?of?full?span?(whichever?is?greater)
Resolution: 1mm
Analogue?Output: 4-20mA,?corresponding?to?instantaneous?flow
Relays?Output: Standard?2?relay?outputs(Optional?up?to?6?relays)
Serial?Communication: RS485,?MODBUS?-RTU?standard?protocol

Ultrasonic Flow meter for applications in clean water and in low conductivity media. Operating principle based on transit time measurement.
Pipe material:Steel,Stainless steel,Cast iron,PVC,Cement pipe and allow pipe with lining
High Isolation voltage,Strong anti-interference,Suppress voltage noise,Good isolation performance
Inline ultrasonic flow meter collect temperature signal and accuracy reach 0.001¡æ

RS232 Signal Handheld ultrasonic flow meter Clamp on tranducer is a portable liquid flow measurement device with a sensor. RS232 Signal Handheld ultrasonic flow meter Clamp on tranducer adopt transit-time ultrasonic measurement technology for superior accuracy and ease of installation and installation. This easy-to-use flowmeter comes in a rugged, waterproof carrying case for easy transport of the display, sensor, and cables between measurement locations. High accuracy +/-1.0% of FS Transducer temperature: -30~90¡ãC/-30¡ãC~160¡ãC Measuring clean liquids Battery-powered,for 12 hours Communication: RS232

Wall mounted and handhold portable clamp on ultrasonic water flow meter battery ultrasonic flowmeter is simple to install and is suitable for large diameter pipes requiring monitoring and flow measurement, as well as a wide network of smaller supply lines. Wall mounted and handhold portable clamp on ultrasonic water flow meter battery ultrasonic flowmeter provide the tools needed to meet the diverse requirements of such a demanding industry. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring clean liquids Power supply: 24VDC/85VAC-2265AC Communication: RS485

Wall Mounted Ultrasonic Flowmeter 25mm water flow meter are used in conjunction with clamp on transducer to accurately measure liquid flow in closed pipes without the need to insert any mechanical parts into the pipe wall or into the fluid inside.
Using ultrasonic transit time technology, controlled by a microprocessor system, it holds a large amount of data, making it available for pipes of almost any material, from 15mm to 6000mm diameter (depending on the sensor model). This series can measure fluids at various temperatures (up to 160¡ãC).
Accuracy: +/-1.0% of FS
Wide range: DN15mm-DN6000mm
Measuring clean liquids
Power supply: 24VDC/85VAC-2265AC
Communication: RS485

The ultrasonic open channel flowmeter can be equipped with a communication interface, which is easy to connect with SCADA systems to achieve industrial remote monitoring and control. This Open Channel flow meter measures level, flow rate and total volume of water flowing through weirs, flumes, and channels etc.

Specifications:
Sensor?Level?Range: 0-4.0m; other?level?range?also?available
Blind?zone: 0.20m
Temperature?Compensation: Integral?in?probe
Pressure?Rating: 0.2MPa
Beam?Angle: 8*?(3db)
Cable?Length: 10m?standard?(can?be?extended?to?1000m)
Sensor?Material: ABS,?PVC?or?PTFE?(optional)
Sensor?Protection Class: IP68

Handheld dual power supply ultrasonic flow meter price handhold portable industrial ultrasonic flowmeter wide range of applications,with clamp on transducers to measure flow rate through the pipe wall, the transit time ultrasonic flow principle. It is a 3.6V battery powered ultrsonic flow meter, for using on a wide range of sizes and can provide 24 hours measurement continuely. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring clean liquids Built-in rechargeable battery 3.6V 2000 lines storage Communication: RS232

Liquid flowmeter sensor portable ultrasonic flowmeter is that to use ultrasonic technology to measure the velocity of liquid throught it.It is transit time.With two clamp on transducers to measue Fuel oil, glycol, waste streams, water flow. A user can use hand to hold as well as to operate the ultrasonic water flow meter main unit .The user-interface is self-explanatory and very easy to follow. Besides, the unique clamp-on fixture design makes the installation very simple and no special skills or tools required.
Due to the non-intrusive nature of the clamp-on technique, there is no pressure drop, no moving parts, no leaks and no contamination.
Accuracy: +/-1.0% of FS
Wide range: DN15mm-DN6000mm
Measuring clean liquids
Built-in rechargeable battery 3.6V
Communication: RS232

Transmitter and transducer install seperately.Transmitter can install at indoor,Instrument cabinet,Dashboard.

Wall Mounted ultrasonic liquid flowmeter Clamp on transducer adopts the self-development measurement technology.This measurement technique is a faster and more accurate process time measurement. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring single clean liquids Power supply: 24VDC/85VAC-2265AC Communication: RS485

LCD display Clamp on Portable ultrasonic flowmeter is a wide used time difference ultrasonic flowmeter. It is small and light, the installation process is extremely simply and easy to operate. The design of rechargeable battery and universal power supply enables you to realize pipeline measurement anytime and anywhere.
The portable ultrasonic flowmeter consists of two parts: transmitter unit and transducer. The magnetic external clamp on transducer is easy to insntall and can be attached to a metal pipe for continuous flow measurement. It is especially suitable for on-site flow measurement with various pressure requirements.
Measuring accuracy: +/-1.0% of FS
Transducer temperature: -30~90¡ãC/-30¡ãC~160¡ãC
Measuring clean liquids
Battery-powered,for 12 hours
Communication: RS232

Digital wall Mounted Clamp on Ultrasonic transducer measure flow by propagating ultrasonic waves into a liquid-filled pipe. These wall mounted flowmeter are located outside the pipeline and offer a wide range of pipeline sizes with no pressure loss, no contact with the liquid inside, and no moving parts. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm None cut down pipe Power supply: 24VDC/85VAC-2265AC Communication: RS485

Low cost ultrasonic flow meter has the high-speed data update rate and superior user-friendliness in installation and operation.Economic ultrasonic flow meter without pressure drop or energy loss. Humidity:Up to 99% RH, non-condensing;
Transmitter material: PC/ABS, IP65;
Transducer:ABS,IP68
Accuracy:±1% of measured value;
Repeatability:0.2% of measured value;

Clamp on sensor handheld ultrasonic water Flowmeter is a portable liquid flow measurement device with a sensor. Clamp on sensor handheld ultrasonic water Flowmeter adopt transit-time ultrasonic measurement technology for superior accuracy and ease of installation and installation. This easy-to-use flowmeter comes in a rugged, waterproof carrying case for easy transport of the display, sensor, and cables between measurement locations. High accuracy +/-1.0% of FS Transducer temperature: -30~90¡ãC/-30¡ãC~160¡ãC Measuring clean liquids Battery-powered,for 12 hours Communication: RS232

PLCM series ultrasonic open channel flow meter is a low cost choice. It is a hot sell product for river channel measuring. The product supports weirs or notches of different standards in various countries and can be widely used for measurement or monitoring of total water drainage.
Display: Backlight LCD
The maximum of Accumulative Flow: 9999999.9 m3/h
Accuracy of Change in Level: 1mm or 0.2% of full span (whichever is greater)
Resolution: 1mm
Analogue Output: 4-20mA, corresponding to instantaneous flow
Relays Output: Standard 2 relay outputs(Optional up to 6 relays)
Serial Communication: RS485, MODBUS -RTU standard protocol
Ambient Temperature: -40 ~70 Degree C
Power Supply: DC24V (+5%) 0.2A; AC220V (+20%) 0.1A ;Optional DC12V

This solar power Open Channel Water Meters consists of two elements, a host, which has display and an integral keypad for programming, and a transducer/probe, which must be mounted directly above the surface to be measured. It can be widely applied to the environmental protection, water treatment, irrigation, chemical, and other industries.

Specifications:
Display: Backlight?LCD
Flow?Rate?Range: 0.0000~99999L/S?or?m3/h
The?maximum?of Accumulative Flow: 9999999.9?m3/h
Accuracy?of?Change in Level: 1mm?or?0.2%?of?full?span?(whichever?is?greater)
Resolution: 1mm
Analogue?Output: 4-20mA,?corresponding?to?instantaneous?flow
Relays?Output: Standard?2?relay?outputs(Optional?up?to?6?relays)
Serial?Communication: RS485,?MODBUS?-RTU?standard?protocol

QT621 portable type ultrasonic clamp on flow meters use clamp-on transducers that are mounted externally on the surface of the pipe and which generate pulses that pass through the pipe wall.
Portable ultrasonic flow meters are widely applicated from simple water flow measurements to energy flow monitoring and automated process control.

Size: 1¡å~48¡å(25mm~1200mm)
Flow Range:¡À0.01 m/s~ ¡À12 m/s
Accuracy: ¡À1%
Repeatability: 0.2%
Output: 4-20mA, RS485
Power supply: Internal lithium 3000mAh
Transducer: IP68

QTDS-100F China wall mounted Clamp on pipe ultrasonic water flow meter is a portable flow meter that with external clamp-on transducers, which can meet the needs of convenient and quick flow measurement, allowing clients to quickly transmit and measure data between different working environments and improve work efficiency.
Accuracy: +/-1.0% of FS
Wide range: DN15mm-DN6000mm
Measuring clean liquids
Power supply: 24VDC/85VAC-2265AC
Communication: RS485

Factory supplier LCD displayer digital ultrasonic flow meter price is easy to use, fast to measure flow. It is a popular flowmeter for sewage environmental monitoring departments and large-diameter tap water flow measurement. Factory supplier LCD displayer digital ultrasonic flow meter price has the characteristics of large measurement range, and different types of sensors can be used, which can realize the measurement of pipeline flow with diameters of DN20~DN6000mm. High-precision measurement, the measurement accuracy is better than ¡À1%, the linearity is 0.5%, and the repeatability accuracy is 0.2%. Non-contact measurement The Factory supplier LCD displayer digital ultrasonic flow meter sensor is adsorbed on the outer wall of the pipe to complete the flow measurement. Measuring accuracy: +/-1.0% of FS Transducer temperature: -30~90¡ãC/-30¡ãC~160¡ãC Measuring clean liquids Built-in rechargeable battery 3.6V Communication: RS232

4-20mA Output Ultrasonic Water Flow Meter BTU meter is designed to work with clamp-on transducers to enable the flow of a liquid within a closed pipe to be measured accurately without needing to insert any mechanical parts through the pipe wall or protrude into the flow system.

The majority of wall mount ultrasonic flow meter applied in general industry.liquid ultrasonic flow meter is suitable for measuring variety of different liquids.
Humidity:Up to 99% RH, non-condensing;
Transmitter material: PC/ABS, IP65;
Transducer:ABS,IP68
Accuracy:±1% of measured value;
Repeatability:0.2% of measured value;

QT811 adopts a new external clamp design, which could get the flow rate without touch the measurement medium. Clamp on ultrasonic flow meter is optional to become an ultrasonic cooling (heat) meter/ btu meter/ energy meter to realize the monitoring and measurement of energy. As the advantage of a clamp on flow meter, no need to cut off the pipe or long time stop the equipment, save the cost of time and labor costs.

Pipe Size:?DN15-DN40mm (1/2¡±~1 1/2¡±)
Flow Range:¡À0.1m/s ~¡À5m/s
Temperature: 0~75¡æ (standard)
Output: 4-20mA, OCT Pulse, RS485
Accuracy:?¡À1% of measured value
Power Supply: DC10-24V

This Waste Water open Channel flow meter has wide application, good for applications such as groundwater system flow
monitoring, industrial sewage discharge monitoring, flow into water treatment plants, effluent from water resource recovery, and
agriculture irrigation channels.

Specifications:
Display: Backlight?LCD
Flow?Rate?Range: 0.0000~99999L/S?or?m3/h
The?maximum?of Accumulative Flow: 9999999.9?m3/h
Accuracy?of?Change in Level: 1mm?or?0.2%?of?full?span?(whichever?is?greater)
Resolution: 1mm
Analogue?Output: 4-20mA,?corresponding?to?instantaneous?flow
Relays?Output: Standard?2?relay?outputs(Optional?up?to?6?relays)
Serial?Communication: RS485,?MODBUS?-RTU?standard?protocol

Wall Mounted Ultrasonic flow sensor Water Clamp on flow meter consists of two parts: a transmitter unit and a transducer. Magnetic external clamps on the sensor are easy to install and connect to metal tubing for continuous flow measurement. It is especially suitable for on-site flow measurement of various pressure requirements. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring clean liquids Power supply: 24VDC/85VAC-2265AC Communication: RS485

QT811 external clamp on type ultrasonic energy meters uses clamp-on transducers that are mounted externally on the surface of the pipe and which generate pulses that pass through the pipe wall.
Specially external clamp design, QT811 clamp on ultrasonic energy BTU meter could achieve flow measurement without touch the measurement liquid.

Pipe Size:?DN15-DN40mm (1/2¡±~1 1/2¡±)
Flow Range:¡À0.1m/s ~¡À5m/s
Temperature: 0~75¡æ (standard)
Output: 4-20mA, OCT Pulse, RS485
Accuracy:?¡À1% of measured value
Power Supply: DC10-24V

Inline ultrasonic water flow meter could be manufactured from 50mm~700mm and suitable for continuously measuring flow and heat of clean and uniform liquids without large concentration suspended particles or gases industrial environment.
Input:Two-wire PT1000
Output:4-20mA,Pulse,OCT
Communication:RS485
Szie:DN15~DN6000
Accuracy:¡À1.0 %
Viscosity:0.1~¡À10m/s

An ultrasonic flow meter utilizes ultrasound to measure the velocity of a fluid and is used in a variety of fluid applications
Pipeline ultraosnic flow meter directly contact the liquid and make the measuring accuracy better than clamp on ultrasonic flowmeter.And installation easy,don’t need calculate the sensor installation distance and cover the coupling agent in the pipe,so this meter can collect the signal very well.