Ultrasonic flowmeter handheld ultrasonic flowsensor

Transmitter and transducer install seperately.Transmitter can install at indoor,Instrument cabinet,Dashboard.

Digital wall Mounted Clamp on Ultrasonic transducer measure flow by propagating ultrasonic waves into a liquid-filled pipe. These wall mounted flowmeter are located outside the pipeline and offer a wide range of pipeline sizes with no pressure loss, no contact with the liquid inside, and no moving parts. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm None cut down pipe Power supply: 24VDC/85VAC-2265AC Communication: RS485

Wall Mounted Ultrasonic Flowmeter flow meter can be used with various types of detectors applicable for small to large diameter pipe (0.5″” to 236″” / 15mm to 6000mm) and low to high temperature (?30 to +160¡ãC).
This wall mounted flow meter is designed for 12 hours of continuous operation with a built-in battery ,allows flow, velocity and total data to be stored. Though RS232 to connect with a PC to facilitate configuring the storage as well as saving and reading data files.
Accuracy: +/-1.0% of FS
Wide range: DN15mm-DN6000mm
Measuring clean liquids
Power supply: 24VDC/85VAC-2265AC
Communication: RS485

The Q&T Open channel flow meter using transit-time principle, it is an economical ultrasonic flowmeter specifically designed for open channel. Compared with other ultrasonic flow meters on the market, it has the characteristics of high reaction rate, low power consumption and high certainty. At the same time, with non-contact level sensor, it also have the feature of installation simple easy to use, non need water supply shutdown etc.

Specifications:
Display: Backlight?LCD
Flow?Rate?Range: 0.0000~99999L/S?or?m3/h
The?maximum?of Accumulative Flow: 9999999.9?m3/h
Accuracy?of?Change in Level: 1mm?or?0.2%?of?full?span?(whichever?is?greater)
Resolution: 1mm
Analogue?Output: 4-20mA,?corresponding?to?instantaneous?flow
Relays?Output: Standard?2?relay?outputs(Optional?up?to?6?relays)
Serial?Communication: RS485,?MODBUS?-RTU?standard?protocol

4-20mA Output Ultrasonic Water Flow Meter BTU meter is designed to work with clamp-on transducers to enable the flow of a liquid within a closed pipe to be measured accurately without needing to insert any mechanical parts through the pipe wall or protrude into the flow system.

QTDS-100H Sea Water Ultrasonic Flowmeter incorporates the latest ultrasonic technology to give you an accurate, easy to use hybrid flow meter with transit-time operating modes. With their quick and easy clamp-on transducer installation, factory pre-configuration and user programmable menu driven interface, the ultrasonic flow meters are a snap to commission in the field. The reliable QTDS-100H Sea Water Ultrasonic Flowmeter use custom algorithms and technology to ensure high accuracy flow metering.
Accuracy: +/-1.0% of FS
Wide range: DN15mm-DN6000mm
Medium: clean liquids,pure water
Built-in rechargeable battery 3.6V
Communication: RS232

Protable Ultrasonic Water Flowmeter Price,Ultrasonic Flow Meter is a portable liquid flow measurement device with a sensor. Protable Ultrasonic Water Flowmeter Price,Ultrasonic Flow Meter adopt transit-time ultrasonic measurement technology for superior accuracy and ease of installation and installation. This easy-to-use flowmeter comes in a rugged, waterproof carrying case for easy transport of the display, sensor, and cables between measurement locations. High accuracy +/-1.0% of FS Transducer temperature: -30~90¡ãC/-30¡ãC~160¡ãC Measuring clean liquids Battery-powered,for 12 hours Communication: RS232

Flowmeter Water Wall Mounted Clamp On Ultrasonic Flow Meter Digital Water measure flow by propagating ultrasonic waves into a liquid-filled pipe. These wall mounted flowmeter are located outside the pipeline and offer a wide range of pipeline sizes with no pressure loss, no contact with the liquid inside, and no moving parts. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm None cut down pipe Power supply: 24VDC/85VAC-2265AC Communication: RS485

Digital Ultrasonic Water Flowmeter Wall Mounted Relay alarm and RS485 Modbus flow meters can realize to measure flow.Connect with temperature sensor,it can measure heat flow.

OEM DN15-DN6000 China Wall Mounted Ultrasonic Water Flowmeter is a portable liquid flow measurement device with a sensor. This 2-inch clamp-On Ultrasonic Flow Meterutilizes proven transit-time ultrasonic measurement technology for superior accuracy and ease of installation and installation. This easy-to-use flowmeter comes in a rugged, waterproof carrying case for easy transport of the display, sensor, and cables between measurement locations. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring single clean liquids Power supply: 24VDC/85VAC-2265AC Storage: SD card optional Heat meter optional

The Q&T solar power Open channel flow meter using transit-time principle, it is an economical ultrasonic flowmeter specifically designed for open channel. Compared with other ultrasonic flow meters on the market, it has the characteristics of high reaction rate, low power consumption and high certainty. At the same time, with non-contact level sensor, it also have the feature of installation simple easy to use, non need water supply shutdown etc.

Specifications:
Display: Backlight?LCD
Flow?Rate?Range: 0.0000~99999L/S?or?m3/h
The?maximum?of Accumulative Flow: 9999999.9?m3/h
Accuracy?of?Change in Level: 1mm?or?0.2%?of?full?span?(whichever?is?greater)
Resolution: 1mm
Analogue?Output: 4-20mA,?corresponding?to?instantaneous?flow
Relays?Output: Standard?2?relay?outputs(Optional?up?to?6?relays)
Serial?Communication: RS485,?MODBUS?-RTU?standard?protocol

QT621 ultrasonic water flow meters are popular in oil industry, water treatment, pure water, chemical and etc. Portable ultrasonic flow meter main advantage is that the meter can be easily moved and installed in different pipes and convenient to carry site to site. Adopt the technology of transit time, ultrasonic waves transmitted and received through moving liquid.

Size: 1¡å~48¡å(25mm~1200mm)
Flow Range:¡À0.01 m/s~ ¡À12 m/s
Accuracy: ¡À1%
Repeatability: 0.2%
Output: 4-20mA, RS485
Power supply: Internal lithium 3000mAh
Transducer: IP68

Q&T portable ultrasonic flow meters involves sending and receiving ultrasonic pulses from a pair of sensors and examining the time difference in the signal. Portable ultrasonic flow meter can be easily moved and installed in different pipes and convenient to carry site to site, which is very convenient for users to monitor the data.

Size: 1¡å~48¡å(25mm~1200mm)
Flow Range:¡À0.01 m/s~ ¡À12 m/s
Accuracy: ¡À1%
Repeatability: 0.2%
Output: 4-20mA, RS485
Power supply: Internal lithium 3000mAh
Transducer: IP68

This ultrasonic water flow meter can directly display the instant and accumulative flow. This open channel ultrasonic flow meter is based on the flow rate-water level calculation method, and adopts an advanced flow rate measuring instrument and water level measuring instrument to ensure a new intelligent flow system.

Specifications:
Sensor?Level?Range: 0-4.0m; other?level?range?also?available
Blind?zone: 0.20m
Temperature?Compensation: Integral?in?probe
Pressure?Rating: 0.2MPa
Beam?Angle: 8*?(3db)
Cable?Length: 10m?standard?(can?be?extended?to?1000m)
Sensor?Material: ABS,?PVC?or?PTFE?(optional)
Sensor?Protection Class: IP68
Output: 4-20mA, Relays, RS485

Q&T clamp on small size flow meter involves sending and receiving ultrasonic pulses from clamp on sensors and examining the time difference in the signal. QT811 small pipe ultrasonic clamp on meters are uitable for various liquids and compatible with various pipeline materials and sizes.

Pipe Size:?DN15-DN40mm (1/2¡±~1 1/2¡±)
Flow Range:¡À0.1m/s ~¡À5m/s
Temperature: 0~75¡æ (standard)
Output: 4-20mA, OCT Pulse, RS485
Accuracy:?¡À1% of measured value
Power Supply: DC10-24V

Inline ultrasonic flow meter support single channel and multi-channel at the same time,when one of channel is abnormal or not connected,it can automatically switch to single channel to working
Ultrasonic flow measurement according to the ¡°differential transit time¡± method: This method uses two sensors, set opposite each other in the measuring tube. Each sensor can alternately transmit and receive ultrasonic signals, while simultaneously measuring the signal transit time.

PLCM Open Channel flow meters measure level, flow rate and total volume of water flowing through weirs, flumes, channels and partially filled pipes. The flow meters use a non-contact level sensor. Application field£º
1. Water and sewage treatment£ºpump room, collection well, biochemical reaction
tank, sedimentation tank.
2. Electricity, mines£ºmortar pool, coal slurry pool, butter storage tank, stockyard
or some mobile equipment control, etc.
3. Food industry£ºwineries, granaries, storage tanks for food materials, etc.

Specifications:
Display: Backlight?LCD
The?maximum?of Accumulative Flow: 9999999.9?m3/h
Resolution: 1mm
Analogue?Output: 4-20mA
Relays?Output: Standard?2?relay?outputs(Optional?up?to?6?relays)
Serial?Communication: RS485,?MODBUS RTU
Ambient?Temperature: -40 ~70 Degree C
Power?Supply: DC24V, AC 220V£»Optional?DC12V

Inline ultrasonic water flow meter could be manufactured from 50mm~700mm and suitable for continuously measuring flow and heat of clean and uniform liquids without large concentration suspended particles or gases industrial environment.
Input:Two-wire PT1000
Output:4-20mA,Pulse,OCT
Communication:RS485
Szie:DN15~DN6000
Accuracy:¡À1.0 %
Viscosity:0.1~¡À10m/s

Digital portable ultrasonic flowmeters are widely used in tap water, heating, water conservancy, metallurgy, chemical industry, machinery, energy and other industries. It can be used for production monitoring, flow verification, temporary detection, flow inspection, water meter balance debugging, heat network balance debugging, and energy-saving monitoring. It is a tool instrument for timely flow detection. This ultrasonic flowmeter has a built-in data logger. The built-in data logger has a space of 24K bytes and can store 2000 lines of measurement data. The rechargeable power supply has a built-in high-capacity nickel-metal hydride rechargeable battery, which can support the flowmeter to work continuously for more than 12 hours. Measuring accuracy: +/-1.0% of FS Transducer temperature: -30~90¡ãC/-30¡ãC~160¡ãC Measuring clean liquids Battery-powered,for 12 hours Communication: RS232

Clamp on type sensor ultrasonic water flow meter no pipe cutting required. The user simply clamp on the flow sensor to the pipe surface. Clamp on type sensor ultrasonic water flow meter can then detect the flow through ultrasonic waves, and then automatically calculate the flow rate value, flow accumulator, etc. No pipe cutting means no damage to the pipe. So as long as the pipes are in good condition, the installation on the flowmeter will not provide the possibility of leakage. Sensor: Clamp-on/External Principle: transmit time Size: DN15mm-DN6000mm Measuring medium: Liquid 3.6V Battery-powered

RS232 Signal Handheld ultrasonic flow meter Clamp on tranducer is a portable liquid flow measurement device with a sensor. RS232 Signal Handheld ultrasonic flow meter Clamp on tranducer adopt transit-time ultrasonic measurement technology for superior accuracy and ease of installation and installation. This easy-to-use flowmeter comes in a rugged, waterproof carrying case for easy transport of the display, sensor, and cables between measurement locations. High accuracy +/-1.0% of FS Transducer temperature: -30~90¡ãC/-30¡ãC~160¡ãC Measuring clean liquids Battery-powered,for 12 hours Communication: RS232

QT811 clamp on ultrasonic flow meter support a variety of modes which are available for setting and flexibility.
One set is universal for all pipe size in the measuring range, and suitable for many kinds of metal and resin
pipes. Clamp on ultrasonic flow meter support remote monitoring.
with the help of output, could
send the information to PLC,
central control room and etc.

Pipe Size:?DN15-DN40mm (1/2¡±~1 1/2¡±)
Flow Range:¡À0.1m/s ~¡À5m/s
Temperature: 0~75¡æ (standard)
Output: 4-20mA, OCT Pulse, RS485
Accuracy:?¡À1% of measured value
Power Supply: DC10-24V

Multi-channel ultrasonic flow meter could be manufactured from 50mm~700mm and mainly be used to measure the flow
and heat of clean liquid which don’t contain large concentration of suspended particles or gas.
RS485 communication
Accuracy:¡À0.5%
Flow velocity:0.1~¡À7m/s
Input:Two-wire PT1000
Supporting single channel and multi-channel

New Version Protable Ultrasonic Water Flowmeter Price For Sale,Ultrasonic Flow Meter is a portable liquid flow measurement device with a sensor. New Version Protable Ultrasonic Water Flowmeter Price For Sale,Ultrasonic Flow Meter adopt transit-time ultrasonic measurement technology for superior accuracy and ease of installation and installation. This easy-to-use flowmeter comes in a rugged, waterproof carrying case for easy transport of the display, sensor, and cables between measurement locations. High accuracy +/-1.0% of FS Transducer temperature: -30~90¡ãC/-30¡ãC~160¡ãC Measuring clean liquids Battery-powered,for 12 hours Communication: RS232

QT811 DN15-40mm clamp on flow meter is a new designed external clamp on measurement flow meter. Clamp on ultrasonic flow meter adopt non-invasive flow measurements, This involves sending and receiving ultrasonic pulses from a pair of sensors and examining the time difference in the signal. Clamp on flow meter support monitor the flow rate reading directly on the device.

Pipe Size:?DN15-DN40mm (1/2¡±~1 1/2¡±)
Flow Range:¡À0.1m/s ~¡À5m/s
Temperature: 0~75¡æ (standard)
Output: 4-20mA, OCT Pulse, RS485
Accuracy:?¡À1% of measured value
Power Supply: DC10-24V

QTLD-100F is a fixed wall-mounted ultrasonic flowmeter, which adopts the self-developed time difference measurement technology. Compared with other common algorithms in China, the measurement technology is an algorithm for measuring process time with higher speed and higher precision.
Accuracy: +/-1.0% of FS
Wide range: DN15mm-DN6000mm
Measuring single clean liquids
Power supply: 24VDC/85VAC-2265AC
Communication: RS485

QT621 Portable ultrasonic flow meter applicable in all areas such as drinking water and sewerage industry, power plants,producing industry, food industry and many more. Portable ultrasonic water flow meter mainly consists of two parts, transmitter and transducer. QT621 ultrasonic flow meter support quickly verify the flow reading of another meter and to data log flow system values over an extended time period.

Size: 1¡å~48¡å(25mm~1200mm)
Flow Range:¡À0.01 m/s~ ¡À12 m/s
Accuracy: ¡À1%
Repeatability: 0.2%
Output: 4-20mA, RS485
Power supply: Internal lithium 3000mAh
Transducer: IP68

QT811 clamp on ultrasonic flow meter is with specially design with built-in transducers and LCD monitor in one body. Clamp-on transducers are mounted externally on the surface of the pipe and which generate pulses that pass through the pipe wall. The flowing
liquid within causes time differences in the ultrasonic signals, which are then evaluated by the flowmeter to
produce an accurate flow measurement.

Pipe Size:?DN15-DN40mm (1/2¡±~1 1/2¡±)
Flow Range:¡À0.1m/s ~¡À5m/s
Temperature: 0~75¡æ (standard)
Output: 4-20mA, OCT Pulse, RS485
Accuracy:?¡À1% of measured value
Power Supply: DC10-24V

Handheld Ultrasonic Water flow sensor portable flow meter no pipe cutting required. The user simply clamp on the flow sensor to the pipe surface. Handheld Ultrasonic Water flow sensor portable flow meter can then detect the flow through ultrasonic waves, and then automatically calculate the flow rate value, flow accumulator, etc. No pipe cutting means no damage to the pipe. So as long as the pipes are in good condition, the installation on the flowmeter will not provide the possibility of leakage. Sensor: Clamp-on/External Principle: transmit time Size: DN15mm-DN6000mm Measuring medium: Liquid 3.6V Battery-powered

Clamp-on ultrasonic liquid water flow meter proven transit-time ultrasonic measurement technology This technology can be used for permanent installations where intrusive flow meters are not economically viable for permanent installations on large pipelines and for all the different process fluids encountered in the network. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring clean liquids Power supply: 24VDC/85VAC-2265AC Communication: RS485