Top Quality Non-contact solar power ultrasonic water flow meter

This solar power open Channel flow meter waste water has wide application, it can be used for continuous measuring of municipal rain-water, wastewater, sewage discharge and irrigation water pipelines. This Open Channel flow meter measures level, flow rate and total volume of water flowing through weirs, flumes, and channels etc.

Specifications:
Display: Backlight?LCD
Flow?Rate?Range: 0.0000~99999L/S?or?m3/h
The?maximum?of Accumulative Flow: 9999999.9?m3/h
Accuracy?of?Change in Level: 1mm?or?0.2%?of?full?span?(whichever?is?greater)
Resolution: 1mm
Analogue?Output: 4-20mA,?corresponding?to?instantaneous?flow
Relays?Output: Standard?2?relay?outputs(Optional?up?to?6?relays)
Serial?Communication: RS485,?MODBUS?-RTU?standard?protocol

The fixed type ultrasonic flow meter, can be used for nearly any liquid from pure water, sewer water, petrol chemicals, metallurgy, electric power plant coolant flow, irrigation, city water, energy monitoring, the meter can indicate flow velocity, flow rate, total flow for nearly any fluid.
Accuracy: +/-1.0%
for pipelines from DN15mm up-to DN6000mm
for flow speeds as low as 0.01 m/s and as high as 32 m/s
for ambient temperatures as low as -65 deg C and as high as +70 deg C and at 100% humidity
for liquid temperatures in the range of -30 deg up-to 160 deg C
Non-contact and low-maintenance sensor
Wide selection

This solar power ultrasonic water flow meter can directly display the instant and accumulative flow. This open channel ultrasonic flow meter is based on the flow rate-water level calculation method, and adopts an advanced flow rate measuring instrument and water level measuring instrument to ensure a new intelligent flow system.

Specifications:
Sensor?Level?Range: 0-4.0m; other?level?range?also?available
Blind?zone: 0.20m
Temperature?Compensation: Integral?in?probe
Pressure?Rating: 0.2MPa
Beam?Angle: 8*?(3db)
Cable?Length: 10m?standard?(can?be?extended?to?1000m)
Sensor?Material: ABS,?PVC?or?PTFE?(optional)
Sensor?Protection Class: IP68
Output: 4-20mA, Relays, RS485

Wall Mounted Ultrasonic Flowmeter 25mm water flow meter are used in conjunction with clamp on transducer to accurately measure liquid flow in closed pipes without the need to insert any mechanical parts into the pipe wall or into the fluid inside.
Using ultrasonic transit time technology, controlled by a microprocessor system, it holds a large amount of data, making it available for pipes of almost any material, from 15mm to 6000mm diameter (depending on the sensor model). This series can measure fluids at various temperatures (up to 160¡ãC).
Accuracy: +/-1.0% of FS
Wide range: DN15mm-DN6000mm
Measuring clean liquids
Power supply: 24VDC/85VAC-2265AC
Communication: RS485

Portable ultrasonic flow meter clamp on ultrasonic flow meter water ultrasonic flow meter measure flow by propagating ultrasonic waves into a liquid-filled pipe. These Portable ultrasonic flow meter clamp on ultrasonic flow meter water ultrasonic flow meter are located outside the pipeline and offer a wide range of pipeline sizes with no pressure loss, no contact with the liquid inside, and no moving parts. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm None cut down pipe Power supply: 24VDC/85VAC-2265AC Communication: RS485

An ultrasonic flow meter utilizes ultrasound to measure the velocity of a fluid and is used in a variety of fluid applications
Pipeline ultraosnic flow meter directly contact the liquid and make the measuring accuracy better than clamp on ultrasonic flowmeter.And installation easy,don’t need calculate the sensor installation distance and cover the coupling agent in the pipe,so this meter can collect the signal very well.
Szie:DN15~DN6000
Accuracy:¡À1.0 %
Viscosity:0.1~¡À10m/s
Output:4~20mA,Pulse,OCT,RS485
Body material:Standard carbon steel,SS304 and SS316 are optional

Handheld Ultrasonic Flow Meter(QTDS-100H)- Wide range of applications,with clamp on transducers to measure flow rate through the pipe wall, the transit time ultrasonic flow principle. It is a 3.6V battery powered ultrsonic flow meter, for using on a wide range of sizes and can provide 24 hours measurement continuely. Accuracy: +/-1.0% of FS Wide range: DN300mm-DN6000mm Measuring clean liquids Built-in rechargeable battery 3.6V 2000 lines storage Communication: RS232

Clamp-on ultrasonic flow meters showcase the benefits of digital signal processing: market-leading accuracy, noise immunity and reliability,liquid ultrasonic flow meter popular in many industry. Flow range:± 0.09ft/s ~ ±16ft/s (±0.03m/s ~ ±5m/s);
Outputs:Analog output:4~20mA,max load 750Ω,Pulse output: 0~10KHz;
Communication: RS232/RS485 Mod bus:
Power supply:10~36VDC/1A;
Display:240*128 back lit LCD;

PLCM Open Channel flow meters measure level, flow rate and total volume of water flowing through weirs, flumes, channels and partially filled pipes. The flow meters use a non-contact level sensor. Application field£º
1. Water and sewage treatment£ºpump room, collection well, biochemical reaction
tank, sedimentation tank.
2. Electricity, mines£ºmortar pool, coal slurry pool, butter storage tank, stockyard
or some mobile equipment control, etc.
3. Food industry£ºwineries, granaries, storage tanks for food materials, etc.

Specifications:
Display: Backlight?LCD
The?maximum?of Accumulative Flow: 9999999.9?m3/h
Resolution: 1mm
Analogue?Output: 4-20mA
Relays?Output: Standard?2?relay?outputs(Optional?up?to?6?relays)
Serial?Communication: RS485,?MODBUS RTU
Ambient?Temperature: -40 ~70 Degree C
Power?Supply: DC24V, AC 220V£»Optional?DC12V

RS232 Signal Handheld ultrasonic flow meter Clamp on tranducer is a portable liquid flow measurement device with a sensor. RS232 Signal Handheld ultrasonic flow meter Clamp on tranducer adopt transit-time ultrasonic measurement technology for superior accuracy and ease of installation and installation. This easy-to-use flowmeter comes in a rugged, waterproof carrying case for easy transport of the display, sensor, and cables between measurement locations. High accuracy +/-1.0% of FS Transducer temperature: -30~90¡ãC/-30¡ãC~160¡ãC Measuring clean liquids Battery-powered,for 12 hours Communication: RS232

QT621 handheld type ultrasonic clamp on flow meters are with user-friendly design, with built-in Lithium battery provides up to 12 hours of measurement operation.
Portable ultrasonic flow meters can be easily moved and installed in different pipes and convenient to carry site to site, which is very convenient for users to monitor the data.

Size: 1¡å~48¡å(25mm~1200mm)
Flow Range:¡À0.01 m/s~ ¡À12 m/s
Accuracy: ¡À1%
Repeatability: 0.2%
Output: 4-20mA, RS485
Power supply: Internal lithium 3000mAh
Transducer: IP68

Not affected by water quality, the solar power ultrasonic open channel flowmeter can be equipped with a communication interface, which is easy to connect with SCADA systems to achieve industrial remote monitoring and control. This Open Channel flow meter measures level, flow rate and total volume of water flowing through weirs, flumes, and channels etc.

Specifications:
Sensor?Level?Range: 0-4.0m; other?level?range?also?available
Blind?zone: 0.20m
Temperature?Compensation: Integral?in?probe
Pressure?Rating: 0.2MPa
Beam?Angle: 8*?(3db)
Cable?Length: 10m?standard?(can?be?extended?to?1000m)
Sensor?Material: ABS,?PVC?or?PTFE?(optional)
Sensor?Protection Class: IP68

Ultrasonic Irrigation Open channel flow meter is for measuring water flow rates in irrigation channels, streams, and storm water systems. Open Channel Flow Meter can be used for continuous measuring of municipal rain-water, wastewater, sewage discharge and irrigation water pipelines.We have both transit-time ultrasonic open channel flow meter and doppler type ultrasonic open channel flow meter.

Specifications:
Analogue?Output: 4-20mA,?corresponding?to?instantaneous?flow
Relays?Output: Standard?2?relay?outputs(Optional?up?to?6?relays)
Serial?Communication: RS485,?MODBUS?-RTU?standard?protocol
Ambient?Temperature: -40 ~70 Degree C
Measure?Cycle: 1?second?(selectable?2?seconds?)
Power?Supply: DC24V?(+5%)?0.2A;?AC220V?(+20%)?0.1A?;Optional?DC12V

Clamp flow meter fixed sewage ultrasonic flowmeter cutting required. The user simply clamp on the flow sensor to the pipe surface. Clamp flow meter fixed sewage ultrasonic flowmeter can then detect the flow through ultrasonic waves, and then automatically calculate the flow rate value, flow accumulator, etc. No pipe cutting means no damage to the pipe. So as long as the pipes are in good condition, the installation on the flowmeter will not provide the possibility of leakage. Sensor: Clamp-on/External Principle: transmit time Size: DN15mm-DN6000mm Measuring medium: Liquid 3.6V Battery-powered

With ultrasonic flow meters, the flow of liquids can be measured reliably – independent of conductivity, pressure, temperature, and in applications where traceability and guaranteed accuracy are required, the external ultrasonic sensor is the first choice. Clamp-on ultrasonic sensors, on the other hand, are mounted on the outer wall of the pipe and can therefore also be used for temporary measurements.
Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring clean liquids Built-in rechargeable battery 3.6V Communication: RS232

DN80mm ultrasonic flowmeter water flow mter is an ultrasonic flowmeter used to measure the flow rate of liquids in closed pipes. The transducer is clamp-on type, which will provide the benefits of contamination-free operation and ease of installation. The transit time flowmeter includes two transducers, which act as ultrasonic transmitters and receivers. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring clean liquids Power supply: 24VDC/85VAC-2265AC Communication: RS485

Using ultrasonic transit time techniques,Wall Mounted Ultrasonic Water Flowmeter is controlled by a micro-processor system which contains a wide range of data that enables it to be used with pipes with an outside diameter ranging from 15mm up to 1200mm (depending on model) and constructed of almost any material. instrument will also operate over a wide range of fluid temperatures.

Handheld Ultrasonic Flowmeter Clamp on Flow Meter Portable Liquid Flow Meter with small transducer use ultrasonic technology to measure the velocity of the liquid. Ultrasonic meters are avaiable as clamp-on solutions. Non pipe cutting, this ultrasonic flow meters can display velocity and accumulated flow. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Medium: clean liquids,pure water Built-in rechargeable battery 3.6V Housing Material: ABS

The structure of 3.6V Waste Water Portable Handheld Ultrasonic Flow Meter is mainly divided into ultrasonic flow unit, flow transducer and information processing circuit, flow display. First, the ultrasonic signal generator is used to send the signal, the sensor receives the signal, and the time difference is obtained. The ultrasonic information is processed according to the information processing circuit, and the flow is transmitted to the display screen in the form of an electrical signal, and the result is displayed Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Medium: clean liquids,pure water Built-in rechargeable battery 3.6V Measurment unit: Meter, Feet,Cubic Meter.

QT811 external clamp on ultraonic flow meter is an easy operation instrument for non-invasive, quick flow and energy measurement with clamp-on technology for many types of pipings.QT811 clamp on flow meter support user to monitor the flow rate reading directly on the device. With various kinds of outputs signals, could send the information to PLC,
central control room and etc.

Pipe Size:?DN15-DN40mm (1/2¡±~1 1/2¡±)
Flow Range:¡À0.1m/s ~¡À5m/s
Temperature: 0~75¡æ (standard)
Output: 4-20mA, OCT Pulse, RS485
Accuracy:?¡À1% of measured value
Power Supply: DC10-24V

QT621 portable type ultrasonic clamp on flow meters support quite quick verify the flow reading of another meter and to data log flow system values over an extended time period.
Portable ultrasonic flow meter uses clamp-on transducers that are mounted externally on the surface of the pipe and which generate pulses that pass through the pipe wall.

Size: 1¡å~48¡å(25mm~1200mm)
Flow Range:¡À0.01 m/s~ ¡À12 m/s
Accuracy: ¡À1%
Repeatability: 0.2%
Output: 4-20mA, RS485
Power supply: Internal lithium 3000mAh
Transducer: IP68

With RS485 Modbus, the solar power ultrasonic open channel flowmeter can be equipped with a communication interface, which is easy to connect with SCADA systems to achieve industrial remote monitoring and control. This Open Channel flow meter measures level, flow rate and total volume of water flowing through weirs, flumes, and channels etc.

Specifications:
Sensor?Level?Range: 0-4.0m; other?level?range?also?available
Blind?zone: 0.20m
Temperature?Compensation: Integral?in?probe
Pressure?Rating: 0.2MPa
Beam?Angle: 8*?(3db)
Cable?Length: 10m?standard?(can?be?extended?to?1000m)
Sensor?Material: ABS,?PVC?or?PTFE?(optional)
Sensor?Protection Class: IP68

Q&T Clamp-on Portable ultrasonic flow meter is the non-invasive method of high accurate flow measurement. The special design includes matching senssors for ease of use ideal for installation in existing systems. The QTDS-100H is designed for ?¡± to 240¡±.
Measuring accuracy: +/-1.0% of FS
Transducer temperature: -30~90¡ãC/-30¡ãC~160¡ãC
Measuring clean liquids
Built-in rechargeable battery 3.6V
Communication: RS232

Modular type ultrasonic flow meter is one type of ultrasonic flow meter.It has very small size and easy to be installed into instrument box. This type flow is working with clamp type transducer normally. The max measure tube is DN3000 pipe. It have 4-02mA, pulse, and RS485 output also.It even could link with temperature sensor and work as ultrasonic BTU meter.
Accuracy: ±1%
Velocity: 0.5s
Display: LCD with backlight 2*20leters
Signal Outputs: 4-20mA or o-20mA,RS485,Pulse
Liquid Types: Virtually all commonly used liquids
Pipe Size: DN15-DN3000

Fixed type clamp on flowmeter with RS485 Modbus flow meter is an ultrasonic flowmeter used to measure the flow rate of liquids in closed pipes. The transducer is a non-contact, clamp-on type, which will provide the benefits of contamination-free operation and ease of installation. The transit time flowmeter employs two transducers, which act as ultrasonic transmitters and receivers. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring clean liquids Power supply: 24VDC/85VAC-2265AC Communication: RS485

QTDS-100H handheld liquid ultrasonic flow meter China supplier is a portable liquid flow measurement device with a sensor. QTDS-100H handheld liquid ultrasonic flow meter China supplier proven transit-time ultrasonic measurement technology for superior accuracy and ease of installation and installation. This easy-to-use flowmeter comes in a rugged, waterproof carrying case for easy transport of the display, sensor, and cables between measurement locations. High accuracy +/-1.0% of FS Transducer temperature: -30~90¡ãC/-30¡ãC~160¡ãC Measuring clean liquids Battery-powered,for 12 hours Communication: RS232

Ultrasonic flow meter with RS232 communication for clean liquid is a non-contact instrument, which can measure the flow of medium with large diameter and can also be used for the measurement of medium that is not easy to contact and observe. Its measurement accuracy is very high, and the external clip-type installation can reach the highest accuracy of ¡À1.0%. It is almost not disturbed by various parameters of the measured medium, especially it can solve the strong corrosiveness, non-conductivity, Flow measurement of radioactive and flammable and explosive media. Measuring accuracy: +/-1.0% of FS Transducer temperature: -30~90¡ãC/-30¡ãC~160¡ãC Measuring clean liquids Battery-powered,for 12 hours Communication: RS232

QT621 handheld type ultrasonic water flow meter adopt transit-time principle. Portable ultrasonic flow meters are with clamp-on transducers for non-invasive liquid measurement of clean homgeneous fluids.Clamp-on transducers create no wear, zero pressure loss,
and do not require process interruptions to install them since they are attached to the outside of the pipe.

Size: 1¡å~48¡å(25mm~1200mm)
Flow Range:¡À0.01 m/s~ ¡À12 m/s
Accuracy: ¡À1%
Repeatability: 0.2%
Output: 4-20mA, RS485
Power supply: Internal lithium 3000mAh
Transducer: IP68

Q&T portable ultrasonic flow meters involves sending and receiving ultrasonic pulses from a pair of sensors and examining the time difference in the signal. Portable ultrasonic flow meter can be easily moved and installed in different pipes and convenient to carry site to site, which is very convenient for users to monitor the data.

Size: 1¡å~48¡å(25mm~1200mm)
Flow Range:¡À0.01 m/s~ ¡À12 m/s
Accuracy: ¡À1%
Repeatability: 0.2%
Output: 4-20mA, RS485
Power supply: Internal lithium 3000mAh
Transducer: IP68

Ultrasonic Flowmeter Portable Clamp on Ultrasonic Flow Meter is a non-contact instrument, which can measure the flow of medium with large diameter and can also be used for the measurement of medium that is not easy to contact and observe. Its measurement accuracy is very high, and the external clip-type installation can reach the highest accuracy of ¡À1.0%. It is almost not disturbed by various parameters of the measured medium, especially it can solve the strong corrosiveness, non-conductivity, Flow measurement of radioactive and flammable and explosive media. Measuring accuracy: +/-1.0% of FS Transducer temperature: -30~90¡ãC/-30¡ãC~160¡ãC Measuring clean liquids Battery-powered,for 12 hours Communication: RS232