Thread connect LPG thermal gas flowmeter

Thermal gas mas flow meters are measuring the mass flow or volume flow of gas,flow range can do 0.5Nm/s¡«100Nm/s. So this meter also can be used for gas leak detection.
Thermal flow sensor temp is always 30¡æ higher than the medium temperature (environment temperature), and the meter adopts method of constant differential temperature, therefore the meter don¡¯t need temperature and pressure compensation in principle.
Accuracy:
In-line type accuracy:¡À1.0%
Insertion type accuracy::¡À1.5%
Power supply:DC24V and AC220V
Output:4-20mA,Pulse,RS485
Body material:Standard SS304,and SS316 is optional
Velocity:0.1~100Nm/s
Media temperature:-40~+220¡æ

Thermal meters require a fully developed flow profile as a prerequisite for correct flow measurement.
When the gas is very humid or saturated with water (e. g. Bio Gas), the piping and flowmeter body should be insulated to prevent water droplets condensing on the measuring sensor.
DC4-20mA four-wire output
Mass flow unit
Dual power:24VDC,220VAC
Min.Flow veloctiy:0.1Nm/s
Output:4-20mA

Thermal gas mass flowmeter have an impressively high accuracy, short response time and a very wide flow range with virtually no loss of accuracy even at the lowest flow rates.It is designed on the basis of thermal dispersion, and adopts method of constant differential temperature to measuring gas flow. It has advantages of small size, easy installation, high reliability and high accuracy, etc.
Media temperature:-40~+220¡æ
Size£º
Insertion type:DN32~DN4000
Flange type:DN10~DN300
Tri-clamp type :DN10~DN100
Thread type:DN10~DN100

Wafer type thermalg gas mass flow meter is an instrument which measures fluid flow by means of heat conduction.
Straight pipe runs can be reduced by using dual-plate flow conditioning elements and installation is very simple with minimal pipe intrusions.
Body material is SS304
Large diameter, low flow rate, negligible pressure loss

Thermal flow meter is accurate, easy to install, no moving parts and best suitable solution for measuring and controlling compressed Air, oxygen, nitrogen, biogas, digester gases, ethane and natural gas flow. Heat dispersion (mass flow) technology to provide proportional mass flow measurement resulting in higher accuracy performance at a lower cost than orifice flow meter, Vortex flow meter and other gas flow measuring devices.
Power supply:DC24V and AC220V
Output:4-20mA,Pulse,RS485
Body material:Standard SS304,and SS316 is optional
Velocity:0.1~100Nm/s
Media temperature:-40~+220¡æ

Q&T brand thermal gas flow meter adopt gas venturi sonic nozzle calibration device regular insprction and verification guarantee accuracy and reliability of the calibration device.
According to clients request,Q&T also can apply the CNAS certificates for the thermal flow meter
Media:All gas except acetylene and humid gas
Measure range:1:100
Sesnsor working temperature:-20~220℃
Transmitter working temperature:-20~45℃
Output:4-20mA

Thermal gas mass flowmeter’s medium temperature range of meter is -40¡æ¡«220¡æ.
When the gas is very humid or saturated with water (e. g. Bio Gas), the piping and flowmeter body should be insulated to prevent water droplets condensing on the measuring sensor.
Insertion type:DN32~DN4000
Flange type:DN10~DN300
Tri-clamp type :DN10~DN100
Thread type:DN10~DN100

Thermal gas flowmeter is mainly used for measuring gas with low flow and the range could reach 1:100,which is btter than gas flowmeter on market and low flow could be measured,the min.flow velocity can reach 0.1Nm/s and Max. velocity reach 100Nm/s
Volume flow /Mass flow
Pressure:
Insertion type¡Ü1.6Mpa
Flange type ¡Ü4.0Mpa
Accuracy:
In-line type accuracy:¡À1.0%
Insertion type accuracy::¡À1.5%
Power supply:DC24V and AC220V

SS304 is the standard material for thermal gas mass flow meter and thermal flow meter is digital display and can
with RS485 or HART communication
Sesnsor working temperature:-20~220¡æ
Transmitter working temperature:-20~45¡æ
Thermal gas flow meter can measure many kinds of gases except acetylene and humid gas and m,easure range can reach 1:100,so it usually be used for leak detection

Insertion type thermal flow meter which be used to measure the air flow velocity.
Air velocity thermal flow meter with widely flow range and flow ratio can reach 1:100.
Measuring tube dia. is ¦Õ12mm and ball valve is 1/2″ NPT
24VDC power supply its more safety for gas.

Thernal gas flow meter is one kind smart gas flow instrument, It can easily and accurately detect the mass flowrate of gas,specical for low flowrate.
Such as :Air, Nitrogen, Hydrogen, Oxygen, Chlorine, Natural gas, Flue gas and Other gases (except acetylene gas)
Thermal gas mass flow emter be widely used in the process control and gas flow measurement of petroleum, chemical industry, metallurgy, electric power, water treatment, papermaking, food, medicine, cement, textile and various production and scientific research institutions.
Media:All gas except acetylene and humid gas
Measure range:1:100
Sesnsor working temperature:-20~220℃
Transmitter working temperature:-20~45℃
Output:4-20mA
Accuracy:±1.0%~±2.5%
Probe material:SS316L
Power supply:24VDC ,220VAC
Response time:1S
Display:4 line digital

Thermal gas mass flow meter sensor is adopted reinforcing design and the root is partially reinforced to make the probe stronger and more suitable for a variety of media
Thermal mass flow meter is precision instruments that can directly measure mass flow,such as industrial gases, compressed gas, and other gases.
DC4-20mA four-wire output
Mass flow unit
Dual power:24VDC,220VAC
Min.Flow veloctiy:0.1Nm/s
Output:4-20mA

Thermal gas mass flowmeters directly indicate the mass flow or normalized volume flow of gases without any additional pressure and temperature compensation. They have an impressively high accuracy, short response time and a very wide flow range with virtually no loss of accuracy even at the lowest flow rates and the range could reach 1:100.
Volume flow /Mass flow
SUS304 body
MODBUS RTU RS485
0.1~100Nm/s
4 lines LCD
EX-PROOF

For the insertion type instrument, on the premise that both the measuring media and field environment are applicable for online dismantlement with non-stop operation, it is viable to have maintenance operation with non-stop operation relying on its special structure.
Velocity:0.1~100Nm/s
Media temperature:-40~+220¡æ
Size£º
Insertion type:DN32~DN4000
Flange type:DN10~DN300
Tri-clamp type :DN10~DN100
Thread type:DN10~DN100

Air thermal gas mass flow meter is very intelligent gas flow meter and can display Nm3 and Kg unit at same time.
And thermal gas mass flow meter be adopted dual power supply,user can easy to choose the poer spurce.
Thermal flow meter measure gas mass flow in various processes and offer distinct advantages, such as repeatability, low maintenance, and operating over a wide flow range. Here we discuss the meter¡¯s fundamentals, the working principle of thermal mass flow measurement, and the two approaches to measuring heat dissipation.

LCD display thermal gas flow meter is a meter that uses the principle of heat transfer to detect flow.
The thermal gas flow meter is available in high-performance pipeline type and insert type flow meter. Insert flow meter consist of a probe with sensing elements that are inserted into the pipe irrespective of pipe size. These are easy to install and more economical. Inline flow meters are connected to the pipe itself by the flanged or threaded connection. Inline meters are suitable for smaller diameter pipes.

The thermal gas flowmeter is mainly used for measuring gas with low flow and the range could reach 1:100,which is btter than gas flowmeter on market and low flow could be measured,the min.flow velocity can reach 0.1Nm/s and Max. velocity reach 100Nm/s
Media:All gas except acetylene and humid gas
Measure range:1:100
Sesnsor working temperature:-20~220℃
Transmitter working temperature:-20~45℃
Output:4-20mA
Accuracy:±1.0%~±2.5%
Probe material:SS316L
Power supply:24VDC ,220VAC
Response time:1S
Display:4 line digital

Thermal gas mass flow meter mainly measure various of gases ,special dry gases,but thermal gas mass flow meter can’t measure acetylene.
In many applications, the thermal properties of the fluid can be dependent upon fluid composition. In such applications, varying composition of the fluid during actual operation can affect the thermal flow measurement. Therefore, it is important for the thermal flow meter supplier to know the composition of the fluid so that the proper calibration factor can be used to determine the flow rate accurately
Widly flow range ratio:1:100
Display:4 line digital
With RS485 or HART communication
Power supply:24VDC ,220VAC
Accuracy:¡À1.0%~¡À1.5%

Except for acetylene,thermal gas mass flowmeters can measure various of dry gas.
Such as Air, Natrual gas, N2, O2, CO2 etc.When measure the flammable and explosive gas,the flow meter need with ex-proof function.
24VDC will better and safety

As the flow meter final manufacturer,OEM and ODM are very normal ,such as Color,Material,Display,Output,Process Connect,Function etc.
Q&T brand thermal mass flowmeters are suitable for all industrial and test rig applications that demand quick and precise gas measurement. The flowmeters directly indicate the mass flow or normalized volume flow of gases without any additional pressure and temperature compensation. They have an impressively high accuracy, short response time and a very wide flow range with virtually no loss of accuracy even at the lowest flow rates.
DC4-20mA four-wire output
Flow unit:Nm3
SS304 rod
All gas except acetylene and humid gas
Measure range:1:100
Sesnsor working temperature:-20~220¡æ
Transmitter working temperature:-20~45¡æ

Except insert type,Q&T also can manufacture Flange thermal flow meter,Thread thermal flow meter ,Wafer type thermal flow meter,Tri-clamp type thermal flow meter .
Q&T also can do OEM for clients,such as Display,Color,Output etc.
Insertion type:DN32~DN4000
Flange type:DN10~DN300
Tri-clamp type :DN10~DN100
Thread type:DN10~DN100

Thermal gas mas flow meters are measuring the mass flow or volume flow of gas,flow range can do 0.5Nm/s¡«100Nm/s. So this meter also can be used for gas leak detection.
Thermal meters require a fully developed flow profile as a prerequisite for correct flow measurement.
When the gas is very humid or saturated with water (e. g. Bio Gas), the piping and flowmeter body should be insulated to prevent water droplets condensing on the measuring sensor.
Flow range:1:100
Pressure up to 4.0Mpa
4-20mA is Optical isolation
Power supply:24VDC&220VAC
Response time:1S

Natural gas thermal mass flow meters measure the mass flowrate of fluids by measuring the heat conducted from a heated surface to the flowing fluid. Since a flowing fluid removes a known quantity of heat as it passes, the temperature difference between the heated sensor and the flow stream is directly proportional to the mass flow rate.
With RS485 or HART communication
Power supply:24VDC ,220VAC
Accuracy:¡À1.0%~¡À1.5%

Thermal gas mass flowmeters are suitable for all industrial and test rig applications that demand quick and precise gas measurement. The flowmeters directly indicate the mass flow or normalized volume flow of gases without any additional pressure and temperature compensation. They have an impressively high accuracy, short response time and a very wide flow range with virtually no loss of accuracy even at the lowest flow rates.
Mass flow
SS304 rod
Dual power:24VDC,220VAC
Min.Flow velocity:0.1Nm/s
Online installation

Thermal gas mass flow meter for pipe dia. DN10~DN2000 and is precision instrument that directly measure gas.
Themal mass flow meter have widely turndown ratio 1:100,so this flow meter is advantage for low flowrate and can be used to detect leak.
Media:All gas except acetylene and humid gas
Measure range:1:100
Sesnsor working temperature:-20~220℃
Transmitter working temperature:-20~45℃
Output:4-20mA

Thermal mass flowmeters are suitable for all industrial and test rig applications that demand quick and precise gas measurement.
Thermal air mass flow meter be adopted the critical flow nozzle calibration device to calibrate each gas mass flow meter,the calibration device flow range can reach Min. 0.5m3/h and Max.10000 m3/h .
Widely turndown ratio:100:1
Power supply:24VDC&220VAC
Response time:1S

Thermal gas mass flow meter is one of kind mass flow meter which is popular in industrial.
Q&T gas mass thermal flow meters are be calibrated by gas venturi sonic nozzle calibration device,and ensure the thermal gas mass flowmeter accuracy can reach 1.0% and 1.5%.
Volume flow /Mass flow
SUS304 body
MODBUS RTU RS485
0.1~100Nm/s
4 lines LCD
EX-PROOF

Q&T thermal gas mass flow meter with DC4-20mA four-wire output,which is more convenient for remote reception.Support MODBUS RTU RS485 protocol,coordinating the receiving system to collect more data ans modify system
Insertion rod diameter :
DN32~DN50 standard rod dia. 12mm ,14mm is optional
DN65~DN4000 standard rod dia.19mm,12mm and 14mm is optional

Split display insert thermal gas mass flow meter is one kind of competitive gas flow meter for natrual gas industry
Easy installation, simple maintenance, two-way detection, anti-vibration
Flow measurement up to 24 points,and its suitable for low flow measurement ,so thermal gas mass flow meter can be used for leak detection

Thermal flowmeters directly indicate the mass flow or normalized volume flow of gases without any additional pressure and temperature compensation. They have an impressively high accuracy, short response time and a very wide flow range with virtually no loss of accuracy even at the lowest flow rates
Mass flow
SS304 rod
Dual power:24VDC,220VAC
Min.Flow velocity:0.1Nm/s
Online installation