LCD display thermal gas mass flow meter

Thermal mass flowmeters are suitable for all industrial and test rig applications that demand quick and precise gas measurement.
Thermal air mass flow meter be adopted the critical flow nozzle calibration device to calibrate each gas mass flow meter,the calibration device flow range can reach Min. 0.5m3/h and Max.10000 m3/h .
Widely turndown ratio:100:1
Power supply:24VDC&220VAC
Response time:1S

Thermal mass flow meters measure the mass flowrate of fluids by measuring the heat conducted from a heated surface to the flowing fluid.Support MODBUS RTU RS485 protocol,coordinating the receiving system .
With RS485 or HART communication
Power supply:24VDC ,220VAC
Accuracy:¡À1.0%~¡À1.5%

Thermal flow sensor temp is always 30¡æ higher than the medium temperature (environment temperature), and the meter adopts method of constant differential temperature, therefore the meter don¡¯t need temperature and pressure compensation in principle
Power supply:DC24V and AC220V
Output:4-20mA,Pulse,RS485
Body material:Standard SS304,and SS316 is optional
Velocity:0.1~100Nm/s
Media temperature:-40~+220¡æ

Thermal gas mass flow meter be adopted LCD converter and its most commonly used to measure the mass flow of clean gases, such as air, nitrogen, hydrogen, helium, ammonia, argon, and other industrial gases.
According to the connect,thermal gas mass flow meter have flange type,thread type,tri-clamp type,wafer type,inertion type etc.
With RS485 or HART communication
Power supply:24VDC ,220VAC
Accuracy:¡À1.0%~¡À1.5%

Intelligent thermal gas mass flow meter with DC4-20mA four-wire output,which is more converient for remote reception.Support MODBUS RTU RS485 protocol.
LCD display thermal gas flow meter is a meter that uses the principle of heat transfer to detect flow.
In-line type accuracy:¡À1.0%
Insertion type accuracy::¡À1.5%
Power supply:DC24V and AC220V
Output:4-20mA,Pulse,RS485

Thermal gas mas flow meters are measuring the mass flow or volume flow of gas,flow range can do 0.5Nm/s¡«100Nm/s. So this meter also can be used for gas leak detection.
Thermal meters require a fully developed flow profile as a prerequisite for correct flow measurement.
When the gas is very humid or saturated with water (e. g. Bio Gas), the piping and flowmeter body should be insulated to prevent water droplets condensing on the measuring sensor.
Flow range:1:100
Pressure up to 4.0Mpa
4-20mA is Optical isolation
Power supply:24VDC&220VAC
Response time:1S

Thermal gas mass flow meter have many benefits -Wide turndown ratio,low pressure drop,application flexibility and gas mass flow rate measurement.This thermal flow meter feature is no moving parts, nearly unobstructed straight through flow path, require no temperature or pressure corrections and retain accuracy over a wide range of flow rates.
RS485 or HART communication
Power supply:24VDC ,220VAC
Accuracy:¡À1.0%~¡À1.5%

Thernal gas flow meter is one kind smart gas flow instrument, It can easily and accurately detect the mass flowrate of gas,specical for low flowrate.
They have an impressively high accuracy, short response time and a very wide flow range with virtually no loss of accuracy even at the lowest flow rates.
Accuracy:¡À1.0 %
4-20mA is Optical isolation
Body material:Standard carbon steel,SS304 and SS316 are optional

Q&T¡®s every thermal gas mass flowmeters be calibrated by critical nozzl flow calibration device to ensure flow meters accuracy.
Thermal meters require a fully developed flow profile as a prerequisite for correct flow measurement.
When the instrument is in used explosion-proof environment, make sure that the explosion-proof certification and temperature class of instrument meet to the requirements on site
Media temperature:-40~+220¡æ
Size£º
Insertion type:DN32~DN4000
Flange type:DN10~DN300
Tri-clamp type :DN10~DN100
Thread type:DN10~DN100

Thermal gas mass flow meter sensor is adopted reinforcing design and the root is partially reinforced to make the probe stronger and more suitable for a variety of media
Thermal mass flow meter is precision instruments that can directly measure mass flow,such as industrial gases, compressed gas, and other gases.
DC4-20mA four-wire output
Mass flow unit
Dual power:24VDC,220VAC
Min.Flow veloctiy:0.1Nm/s
Output:4-20mA

Thermal gas mass flow meter is one kind of precision instrument,ensuring the accuracy is important.
Q&T adopt the critical flow nozzle calibration device to calibrate each gas mass flow meter,the calibration device flow range can reach Min. 0.5m3/h and Max.10000 m3/h .
Nozzle calibration device more ensure the flow meters’ accuracy
Accuracy:
In-line type accuracy:¡À1.0%
Insertion type accuracy::¡À1.5%
Power supply:DC24V and AC220V
Output:4-20mA,Pulse,RS485
Body material:Standard SS304,and SS316 is optional

Thermal gas mass flowmeters are suitable for all industrial and test rig applications that demand quick and precise gas measurement. The flowmeters directly indicate the mass flow or normalized volume flow of gases without any additional pressure and temperature compensation. They have an impressively high accuracy, short response time and a very wide flow range with virtually no loss of accuracy even at the lowest flow rates.
Mass flow
SS304 rod
Dual power:24VDC,220VAC
Min.Flow velocity:0.1Nm/s
Online installation

Thermal gas mas flow meters are measuring the mass flow or volume flow of gas,flow range can do 0.5Nm/s¡«100Nm/s. So this meter also can be used for gas leak detection.
Thermal flow sensor temp is always 30¡æ higher than the medium temperature (environment temperature), and the meter adopts method of constant differential temperature, therefore the meter don¡¯t need temperature and pressure compensation in principle.
Accuracy:
In-line type accuracy:¡À1.0%
Insertion type accuracy::¡À1.5%
Power supply:DC24V and AC220V
Output:4-20mA,Pulse,RS485
Body material:Standard SS304,and SS316 is optional
Velocity:0.1~100Nm/s
Media temperature:-40~+220¡æ

Thermal gas flowmeter is mainly used for measuring gas with low flow and the range could reach 1:100,which is btter than gas flowmeter on market and low flow could be measured,the min.flow velocity can reach 0.1Nm/s and Max. velocity reach 100Nm/s
Volume flow /Mass flow

Thermal gas mass flow meter be adopted LCD converter and its most commonly used to measure the mass flow of clean gases, such as air, nitrogen, hydrogen, helium, ammonia, argon, and other industrial gases.
According to the connect,thermal gas mass flow meter have flange type,thread type,tri-clamp type,wafer type,inertion type etc.
Media:All gas except acetylene and humid gas
Measure range:1:100
Sesnsor working temperature:-20~220℃
Transmitter working temperature:-20~45℃
Output:4-20mA

LCD display thermal gas flow meter is a meter that uses the principle of heat transfer to detect flow.
The thermal gas flow meter is available in high-performance pipeline type and insert type flow meter. Insert flow meter consist of a probe with sensing elements that are inserted into the pipe irrespective of pipe size. These are easy to install and more economical. Inline flow meters are connected to the pipe itself by the flanged or threaded connection. Inline meters are suitable for smaller diameter pipes.

Thermal gas mass flow meter with LCD display,can display volume flow rate,mass flow rate,
total flow and temperature.
Insertion type thermal gas mass flow meter accuracy is 1.5%
Inline type thermal gas mass flow meter accuracy is 1.0%

Tri-clamp thermal gas mass flow meter body be adopted SS304 and probe is SS316
Tri-clamp connect is fast to install and it no moving parts, nearly unobstructed straight through flow path, require no temperature or pressure corrections and retain accuracy over a wide range of flow rates.
Tri-clamp thermal gas mass flow meter size from DN15~DN100mm

Insertion thermal gas mass flow meter with anti flush-out design for high pressure,more safety
When absolute pressure of measuring medium is higher than 5 times standard atmospheric pressure, or higher than the pressure of possible danger, should shut down or do reducing pressure to reach a safety pressure, and then do hot-tapped operation. If there are no conditions to do hot-tapped operation, should shut down to avoid dangers.

Thermal gas mas flow meters are measuring the mass flow or volume flow of gas,flow range can do 0.5Nm/s¡«100Nm/s. So this meter also can be used for gas leak detection.
Thermal flow sensor temp is always 30¡æ higher than the medium temperature (environment temperature), and the meter adopts method of constant differential temperature, therefore the meter don¡¯t need temperature and pressure compensation in principle.

Thermal gas mass flow meter measure the mass flowrate of gases ,so thermal flow meter is often used in monitoring gas mass-related process.
When thermal gas flow meter measure the gases,the gases’ volume measurement is affected by pressure and temperature,while mass flowrate measurement is unaffected by changes in viscosity, density, temperature, or pressure.
Digital display
Stainless steel body
Anti-corrosion
Pressure up to 4.0Mpa
Dural power:24VDC,220VAC
4-20mA is Optical isolation

Sometimes thermal gas mass flow meter be used to measure the dangerous gas,such as Natural gas,H2,O2 etc.So the thermal flow meter need with Ex-proof function.
Except above gas,mass flow meter also can measure N2,Ar,Air,CO2 etc
Flow measurement up to 24 points
Correction of output analog quantity Multipoint nonlinear curve correction
Flow and temperature detection at the same time, switch display
Digital LCD display
Stainless steel body
Output:4-20mA,Pulse,RS485
Accuracy:
In-line type accuracy:¡À1.0%
Insertion type accuracy::¡À1.5%