Stainless Steel digital thread screw turbine flowmeter Crude oil flow meter in liter liquid turbine flowmeter

turbine flow sensor are simple structure, Lightweight, high accuracy, good repeatability, sensitive reaction, low installation and maintenance£¬ Easy to use and so on,it is used in petroleum, chemical, metallurgy, water, paper and other industries, Is to measure the energy flow measurement and instrumentation of the ideal
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%/¡À0.2%;
OUTPUT: PULSE/4-20mA;
Digital Communication:RS485, MODBUS; HART

Turbine flow meter use the mechanical energy of the fluid to rotate a “pinwheel” (rotor) in the flow stream. Blades on the rotor are angled to transform energy from the flow stream into rotational energy. The rotor shaft spins on bearings.
diesel turbine flow meter is a new generation turbine flow meter which was designed with advanced flow technologies both home and aboard.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%/¡À0.2%;
OUTPUT: PULSE/4-20mA;
Digital Communication:RS485, MODBUS; HART

turbine flow meters are used for the precise measurement of instantaneous flow rates of low-viscosity fluids such as tap and demineralized water, fuels, liquefied gases, light fuel oils, solvents, and pharmaceutical fluids
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%;
OUTPUT: PULSE+4-20mA;
Digital Communication:RS485, MODBUS; HART

turbine flow meter refers to the turbine flow sensor with 50mm size. DN50 turbine flow meter can be used to take volumetric flow measurement of petroleum, organic liquid, biogas, LPG gas, liquefied gas, natural gas, hydrocarbon gas, nitrogen, cryogenic fluid, water, diesel, High-pressure hydraulic oil, methanol and other non-impurity, non-corrosive. 2 inch turbine flow meter has many applications in turbine heating systems, boilers measurement of water supply, heat exchange system, air conditioning circulating water, etc.

Works well with Low viscosity liquids. The turbine turns when the good passes through and a pulsed counter provides the flow total on a digital display
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%/¡À0.2%;
OUTPUT: PULSE/4-20mA;
Digital Communication:RS485, MODBUS; HART

QTLL series rotary gas meters are suitable for custody transfer gas measurement of all non-corrosive gases such as natural gas, propane, butane, air, hydrogen etc. Lobed rotary meter is an inexpensive, lightweight, compact, highly accurate gas meter.
Size:DN25-200mm
Material:Aluminum alloy or stainless steel
Dual Power:3.6V battery powered+DC24V
Output:4-20mA,Pulse,RS485
Installation: Vertical or Horizontal
Accuracy:1.5% or 1.0%

QTWG series turbine gas meters are designed to measure natural gas, LPG, air, carbon dioxide and non-corrosive gases. Turbine gas meters deliver high accuracy in gas flow measurements, with built-in volume corrector, integrated temperature and pressure measurement.

Size:DN25-400mm
Material:Aluminum alloy or stainless steel
Dual Power:3.6V battery powered+DC24V
Output:4-20mA,Pulse,RS485
Accuracy:1.5% or 1.0%

tubine flowmeter is Composed of turbine flow sensor and display instrument, it is one of the ideal flow meters for liquid measurement. The flowmeter has the characteristics of simple structure, high accuracy, convenient installation and maintenance, etc. This product is widely used in petroleum, chemical, metallurgy, water supply, papermaking, environmental protection, food and other fields. Impurity liquid. If used in conjunction with a display instrument with special functions, it can be used for automatic quantitative control, excess alarm and other purposes.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%/¡À0.2%;
OUTPUT: PULSE/4-20mA;
Digital Communication:RS485, MODBUS; HART

liquid turbine flow meter is a new generation turbine flow meter which was designed with advanced flow technologies both home and aboard. The product possesses advantages of simple structure, light in weight, high accuracy, good repeatability, short response time, easy installation, etc. It could be used widely in measurement of closed pipe system for pure liquid that will not react with 1Cr18Ni9Ti, 2Cr13, Al2O3 and hard alloys.

Turbine Flow Meters have a unique open bearing design which allows the measured media to flow freely thru the bearings and therefore provides continuous lubrication. This prolongs the life time of the flow meter and allows for free flow of cleaning agents during CIP. This is why we can provide a full 5-year warranty on our whole turbine flow meter series.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%/¡À0.2%;
OUTPUT: PULSE/4-20mA;
Digital Communication:RS485, MODBUS; HART

turbine flow meter is available in a wide range of body sizes and styles to suit liquid flow applications for low to medium viscosity fluids.
The principle of operation is based on a permanent magnet contained within a pick-off coil on the body and a ferritic stainless steel rotor which revolves when flow is present. A small AC voltage is generated in the coil as the rotor tip passes the magnet. The frequency of this AC voltage is directly proportional to the flow rate. The total number of pulses produced represents the total flow passed through the meter.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%/¡À0.2%;
OUTPUT: PULSE/4-20mA;
Digital Communication:RS485, MODBUS; HART

Turbine flowmeters are flow measurement instruments which use axial fluid momentum to turn a multibladed rotor, the angular velocity of which is approximately proportional to the volume flowrate. With appropriate calibration and operation, turbine meters offer precise and highly repeatable measurement of throughput and flowrate.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%/¡À0.2%;
OUTPUT: PULSE/4-20mA;
Digital Communication:RS485, MODBUS; HART

Turbine flowmeter measures the flowrate from the number of revolutions of a blade placed in the flow. The speed of revolutions of the blade with an axis parallel to the flow direction is proportional to the speed of the flow. Utilizing the capability of highly accurate measurement for wide range of viscosity, the turbine flowmeter is useful for process control, transactions as well as process control of petroleum products, general chemical fluids, liquefied gas, water, etc.

turbine Flow meter for diesel is specially designed for usage in water, alcohol, diesel, gasoline and other fluid measurement and control systems. They operate according to the turbine principle, i.e. the speed of an impeller turning in the fluid flow is measured and converted into pulse or 4-20mA signals.

turbine flow transducer adapts to measure the liquid rate and total flowrate of low viscosity. It can be widely used in the fields of Petrol, Chemical industry, Metallurgy, Scientific research for measuring or control. Several output and display methods can be selected.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%;
OUTPUT: PULSE+4-20mA;
Digital Communication:RS485, MODBUS; HART

turbine flow meters are used for the precise measurement of instantaneous flow rates of low-viscosity fluids such as tap and demineralized water, fuels, liquefied gases, light fuel oils, solvents, and pharmaceutical fluids. Turbine flowmeters measure volumetric flow, where fluid passing through the meter body is measured by the mean velocity of the flowing fluid media. Flow rectifiers ensure a laminar flow in the axial direction of the wheel. A low-mass turbine wheel carried concentrically within the meter body is rotated by the fluid. The RPM of the turbine wheel is directly proportional to the mean flow rate within the meter body and directly corresponds to the volumetric flow over a wide range.

turbine flowmeter advantage
1.High accuracy, generally up to ¡À1%R, ¡À0.5%R, high accuracy up to 0.2%R
2.Good repeat-ability, short-term repeat-ability up to 0.05% ~ 0.2%, in the trade settlement is the preferred choice of flow meter.
3.Output of pulse frequency signal, suitable for totalizer and connection with PC; no zero shift and strong interference resist
4.High frequency signal(3~4KHz) can be obtained, the signal resolution is strong.
5.Wide range, medium and large diameter up to 1:20, small caliber 1:10.

Turbine Flow Meters are useful for liquids & gases in general industrial application. They provide excellent performance with quality & reliability. Suitable for as hygienic application. The flowing media engages a vaned rotor causing it to rotate at an angular velocity proportional to flow rate. The pick -of coil senses the spinning motion of the rotor inside the pipe & converts it into a pulsating electrical signal. Summation of the pulsating electrical signal is directly related to the total flow. The frequency is linearly proportional to flow rate which is converted to mA signal by electronic circuitry. Flow rate Indicator / Totalizer / Transmitter and Controllers are available in Local/Remote and Panel Mounted Options.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%/¡À0.2%;
OUTPUT: PULSE/4-20mA;
Digital Communication:RS485, MODBUS; HART

intelligent liquid turbine flow meter is a new type of intelligent instrument with integrated turbine flow sensor and display product calculation developed by advanced ultra-low power single-chip microcomputer technology, which has obvious advantages such as compact mechanism, clear reading, high reliability, undisturbed by external power supply, lightning resistance and low cost.liquid turbine flow meter widely used in petroleum, chemical, metallurgy, water supply, paper-making and other industries. It is an ideal meter for flow metering and energy saving
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%/¡À0.2%;
OUTPUT: PULSE/4-20mA;
Digital Communication:RS485, MODBUS; HART

turbine flow meter widely used in petroleum, chemical, metallurgy, water supply, paper-making and other industries. It is an ideal meter for flow metering and energy saving

Gas turbine flow meter is a new generation of flow measurement device for clean gas, including natural gas, LPG gas etc. Normally LPG gas flow meter need to be with temperature and pressure compensation so that to make sure high accuracy.
Size:DN25-400mm
Material:Aluminum alloy or stainless steel
Dual Power:3.6V battery powered+DC24V
Output:4-20mA,Pulse,RS485
Accuracy:1.5%/1.0%

Gas turbine flow meter is widely used in gas measuring from Petroleum, Chemical, Electricpower,Industrial boiler etc. Natural gas flow meter is a kind of accurate measurement instruments for natural gas, LPG gas application.
Size:DN25-400mm
Material:Aluminum alloy or stainless steel
Dual Power:3.6V battery powered+DC24V
Output:4-20mA,Pulse,RS485
Accuracy:1.5%/1.0%

turbine flow meter has advantage of precision , which can be used to measure the flow and total amount of liquid together with the corresponding flowmeter. When used together with the quantitative control instrument developed by our factory, it can carry out high precision quantitative control of liquid feeding. Widely used in petroleum, chemical, metallurgy, scientific research and other fields of measurement and control system. Turbine flow sensors equipped with sanitary joints can be used in the pharmaceutical industry.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%/¡À0.2%;
OUTPUT: PULSE/4-20mA;
Digital Communication:RS485, MODBUS; HART

Liquid turbine flowmeter as precision instruments for industrial measurement. turbines turbine flowmeters with the advantages of simple structure, light weight, high precision, good reproducibility, sensitive response, and convenient installation, maintenance and use.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%;
OUTPUT: PULSE+4-20mA;
Digital Communication:RS485, MODBUS; HART

Turbine gas flow meters guarantee aaccurate flow measurements for fiscal and non-fiscal appliations.? QTWG series turbine gas meters guarantee are designed to accurately measure natural gas, carbon dioxide, LPG and other non-corrosive gases.
Size:DN25-400mm
Material:Aluminum alloy or stainless steel
Dual Power:3.6V battery powered+DC24V
Output:4-20mA,Pulse,RS485
Accuracy:1.5% or 1.0%

liquid turbine flow meter is a new type of intelligent instrument with integrated turbine flow sensor and display product calculation developed by advanced ultra-low power single-chip microcomputer technology, which has obvious advantages such as compact mechanism, clear reading, high reliability, undisturbed by external power supply, lightning resistance and low cost.

liquid turbine flowmeter, as fluid flows through turbine rotor and drives it to rotate, the rotating rotor periodically cuts magnetic field line to generate electric pulse signal, which can be transmitted to output and transferred to the meter to display flow rater or totalizer. It features in high accuracy, good repeatability, simple structure, low pressure loss, convenient maintenance, etc.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%/¡À0.2%;
OUTPUT: PULSE/4-20mA;
Digital Communication:RS485, MODBUS; HART

QTWG intelligent ex proof natural gas flow meter is widely used for the exact determination of gas quantities. Turbine gas flow meter is widely used in gas measuring from Petroleum, Chemical, Electric power,Industrial boiler etc, which could increase efficiency in boiler/burner control, fuel-to-air ratio, and custody transfer applications.
Size:DN25-200mm
Material:Aluminum alloy or stainless steel
Dual Power:3.6V battery powered+DC24V
Output:4-20mA,Pulse,RS485
Installation: Vertical or Horizontal
Accuracy:1.5% or 1.0%

Turbine flowmeter is a kind of speed meter, which has the advantages of high precision, good repeatability, simple structure, high pressure resistance, wide measurement range, small size, light weight, small pressure loss, long life, simple operation, convenient maintenance, etc. It is used to measure the volume flow and cumulative flow of low-viscosity, non-corrosive, clean liquids in closed pipelines. Can be widely used in petroleum, chemical, metallurgy, organic liquid, inorganic liquid, food, medicine and other industries
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%/¡À0.2%;
OUTPUT: PULSE/4-20mA;
Digital Communication:RS485, MODBUS; HART

Natural gas flow meter is used to measure gas flow, with the features of high accuracy, low-pressure drop. Gas turbine flow meter provides high-quality natural gas measurement which could increase efficiency in boiler/burner control, fuel-to-air ratio, and custody transfer applications.
Size:DN25-400mm
Material:Aluminum alloy or stainless steel
Dual Power:3.6V battery powered+DC24V
Output:4-20mA,Pulse,RS485
Accuracy:1.5%/1.0%