small size built in monitor DN15-DN40 clamp on ultrasonic flow meter

Ultrasonic Flow meter for applications in clean water and in low conductivity media. Operating principle based on transit time measurement.
Pipe material:Steel,Stainless steel,Cast iron,PVC,Cement pipe and allow pipe with lining
High Isolation voltage,Strong anti-interference,Suppress voltage noise,Good isolation performance
Inline ultrasonic flow meter collect temperature signal and accuracy reach 0.001¡æ
When using inline ultrasonic flow meter to measure,allowing pipe with liner

Q&T PLCM Open Channel flow meter is CE Certificated Open Channel Flowmeter, RS485 River Flow Meter Open Channel; The cable length between probe and host up to 1000m; This PLCM ultrasonic flow meters are perfect for wastewater applications.
The probe with leak-proof structure and IP68 protect grade.
Display: Backlight LCD
The maximum of Accumulative Flow: 9999999.9 m3/h
Accuracy of Change in Level: 1mm or 0.2% of full span (whichever is greater)
Resolution: 1mm
Analogue Output: 4-20mA, corresponding to instantaneous flow
Relays Output: Standard 2 relay outputs(Optional up to 6 relays)
Serial Communication: RS485, MODBUS -RTU standard protocol
Ambient Temperature: -40 ~70 Degree C
Power Supply: DC24V (+5%) 0.2A; AC220V (+20%) 0.1A ;Optional DC12V

Highest Quality Handheld ultrasonic flow meter & Solutions, ultrsonic flow meter is a ideal for liquids such as chemical,visous liquids, and sea water. The non-intrusive, clamp-on ultrasonic flow meter fits pipes between 1/2″ to 48″ internal diameter. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Medium: clean liquids,pure water Built-in rechargeable battery 3.6V Measurment unit: Meter, Feet,Cubic Meter.

This open channel flow meter uses ultrasonic principle to measure the water level height in the open channel weir, and then the microprocessor calculates the corresponding flow value automatically. The level value is converted to a particular flow in a particular weirs/flumes, so accurate level values are important. It is a sensor designed for open channel flow to provide accurate level readings.
Power Supply: DC24V (+5%) 0.2A; AC220V (+20%) 0.1A ;Optional DC12V
Flow Rate Range: 0.0000~99999L/S or m3/h
Analogue Output: 4-20mA, corresponding to instantaneous flow
Relays Output: Standard 2 relay outputs(Optional up to 6 relays)
Serial Communication: RS485, MODBUS -RTU standard protocol
Ambient Temperature: -40 ~70 Degree C

The ultrasonic open channel flowmeter can be equipped with a communication interface, which is easy to connect with SCADA systems to achieve industrial remote monitoring and control. This Open Channel flow meter measures level, flow rate and total volume of water flowing through weirs, flumes, and channels etc.

Specifications:
Sensor?Level?Range: 0-4.0m; other?level?range?also?available
Blind?zone: 0.20m
Temperature?Compensation: Integral?in?probe
Pressure?Rating: 0.2MPa
Beam?Angle: 8*?(3db)
Cable?Length: 10m?standard?(can?be?extended?to?1000m)
Sensor?Material: ABS,?PVC?or?PTFE?(optional)
Sensor?Protection Class: IP68

This Industrial waste water treatment flow meter measures level, flow rate and total volume of water flowing through weirs, flumes and channels. The flow meters use a non-contact level sensor. Application field£º
1. Water and sewage treatment£ºpump room, collection well, biochemical reaction
tank, sedimentation tank.
2. Electricity, mines£ºmortar pool, coal slurry pool, butter storage tank, stockyard
or some mobile equipment control, etc.
3. Food industry£ºwineries, granaries, storage tanks for food materials, etc.

Specifications:
Display: Backlight?LCD
The?maximum?of Accumulative Flow: 9999999.9?m3/h
Resolution: 1mm
Analogue?Output: 4-20mA
Relays?Output: Standard?2?relay?outputs(Optional?up?to?6?relays)
Serial?Communication: RS485,?MODBUS RTU
Ambient?Temperature: -40 ~70 Degree C
Power?Supply: DC24V, AC 220V£»Optional?DC12V

This PLCM ultrasonic open channel flow meter is designed for different channel flow metering working with a flume, weir or any other primary device. Non-contact ultrasonic flow meter require accurate measurement of the surface level of a liquid. A flume, channel or structure which has a known characteristic flow per measured head, together with the measured liquid level, accurately define the flow rate through the system.

Analogue?Output: 4-20mA,?corresponding?to?instantaneous?flow
Relays?Output: Standard?2?relay?outputs(Optional?up?to?6?relays)
Serial?Communication: RS485,?MODBUS?-RTU?standard?protocol
Ambient?Temperature: -40 ~70 Degree C
Measure?Cycle: 1?second?(selectable?2?seconds?)
Power?Supply: DC24V?(+5%)?0.2A;?AC220V?(+20%)?0.1A?;Optional?DC12V

Modular Flow Meter is in market in various sizes, designs and shapes. It is highly appreciated for their long functional life.The main unit has the advantages of small size, complete functions and low price. Using guide rail installation, it is suitable to be installed in instrument box or distribution box.
Linearity: 0.5%
Repeatability: 0.20%
Accuracy: Better than ¡À1% for velocity above 0.2m/s
Response Time: 0-999 second, user-configurable
Flow Range: ¡À32m/s
Measuring Pipe Size: 25mm-6000mm
Units: English(U.s.) or metric
Totalizer: 7-digit totalizer for net, positive and negative flow respectively

Wall-mount ultrasonic flowmeter measure flow by propagating ultrasonic waves into a liquid-filled pipe. These wall mounted flowmeter are located outside the pipeline and offer a wide range of pipeline sizes with no pressure loss, no contact with the liquid inside, and no moving parts. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm None cut down pipe Power supply: 24VDC/85VAC-2265AC Communication: RS485

Handheld ultrasonic water flowmeter for liquid is mainly divided into ultrasonic flow unit, flow transducer and information processing circuit, flow display. First, the ultrasonic signal generator is used to send the signal, the sensor receives the signal, and the time difference is obtained. The ultrasonic information is processed according to the information processing circuit, and the flow is transmitted to the display screen in the form of an electrical signal, and the result is displayed Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Medium: clean liquids,pure water Built-in rechargeable battery 3.6V Measurment unit: Meter, Feet,Cubic Meter.

The Solar power GPRS Open Channel Flow Meter has 4-20mA and RS485 signal output, it can be equipped with a communication interface, which is easy to connect with SCADA systems to achieve industrial remote monitoring and control. This Open Channel flow meter measures level, flow rate and total volume of water flowing through weirs, flumes, and channels etc.

Specifications:
Sensor?Level?Range: 0-4.0m; other?level?range?also?available
Blind?zone: 0.20m
Temperature?Compensation: Integral?in?probe
Pressure?Rating: 0.2MPa
Beam?Angle: 8*?(3db)
Cable?Length: 10m?standard?(can?be?extended?to?1000m)
Sensor?Material: ABS,?PVC?or?PTFE?(optional)
Sensor?Protection Class: IP68

Ultrasonic Open channel flow meter is for measuring water flow rates in irrigation channels, streams, and storm water systems. Open Channel Flow Meter can be used for continuous measuring of municipal rain-water, wastewater, sewage discharge and irrigation water pipelines. This open channel flow meter need work together with weirs and flumes.

Specifications:
Analogue?Output: 4-20mA,?corresponding?to?instantaneous?flow
Relays?Output: Standard?2?relay?outputs(Optional?up?to?6?relays)
Serial?Communication: RS485,?MODBUS?-RTU?standard?protocol
Ambient?Temperature: -40 ~70 Degree C
Measure?Cycle: 1?second?(selectable?2?seconds?)
Power?Supply: DC24V?(+5%)?0.2A;?AC220V?(+20%)?0.1A?;Optional?DC12V

QT621 portable type ultrasonic clamp on flow meters support quite quick verify the flow reading of another meter and to data log flow system values over an extended time period.
Portable ultrasonic flow meter uses clamp-on transducers that are mounted externally on the surface of the pipe and which generate pulses that pass through the pipe wall.

Size: 1¡å~48¡å(25mm~1200mm)
Flow Range:¡À0.01 m/s~ ¡À12 m/s
Accuracy: ¡À1%
Repeatability: 0.2%
Output: 4-20mA, RS485
Power supply: Internal lithium 3000mAh
Transducer: IP68

QT621 portable type ultrasonic flow meter is a type of portable instrument for non-invasive, quick flow and energy measurement with clamp-on technology for many types of piping.
Portable ultrasonic flow meter mainly consists of two parts, main display part and transducer part. With 4-20mA and RS485 communication available, QT621 portable ultrasonic flow meter support quickly verify the flow reading of another meter and to data log flow system values over an extended time period.

Size: 1¡å~48¡å(25mm~1200mm)
Flow Range:¡À0.01 m/s~ ¡À12 m/s
Accuracy: ¡À1%
Repeatability: 0.2%
Output: 4-20mA, RS485
Power supply: Internal lithium 3000mAh
Transducer: IP68

According to market request,the power supply can 24VDC or 220VAC or solar powered;Current the solar powered ultrasonic flow meter is more popular,beacuse solar powered meets international requirements, energy saving and environmental protection.

China wall-mounted ultrasonic water flow meter price is an ultrasonic flowmeter used to measure the flow rate of liquids in closed pipes. The transducer is clamp-on type, which will provide the benefits of contamination-free operation and ease of installation. The transit time flowmeter includes two transducers, which act as ultrasonic transmitters and receivers. The transducer can be installed in a v-type method, where the sound travels through the pipe twice, a w-type method, where the sound travels through the pipe four times. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring clean liquids Power supply: 24VDC/85VAC-2265AC Communication: RS485

Wall mounted ultrasonic flow meter clamp on transducer is an ultrasonic flowmeter used to measure the flow rate of liquids in closed pipes. The transducer is clamp-on type, which will provide the benefits of contamination-free operation and ease of installation. The transit time flowmeter includes two transducers, which act as ultrasonic transmitters and receivers. The transducer can be installed in a v-type method, where the sound travels through the pipe twice, a w-type method, where the sound travels through the pipe four times. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring clean liquids Power supply: 24VDC/85VAC-2265AC Communication: RS485

QT621 handheld ultrasonic flow meter support to carry from site to site conveniently. Support accurate bidirectional and highly dynamic flow measurement with the non-invasive clamp-on technology. Portable ultrasonic flow meter mainly applies for measuring the flow of homogeneous medium fluid in the water injection flow measurement, raw water flow measurement, tap water flow measurement etc.

Size: 1¡å~48¡å(25mm~1200mm)
Flow Range:¡À0.01 m/s~ ¡À12 m/s
Accuracy: ¡À1%
Repeatability: 0.2%
Output: 4-20mA, RS485
Power supply: Internal lithium 3000mAh
Transducer: IP68

China supplier lcd displayer digital water flow meter and ultrasonic flow meter price is an ultrasonic flowmeter used to measure the flow rate of liquids in closed pipes. The transducer is a non-contact, clamp-on type, which will provide the benefits of contamination-free operation and ease of installation. The transit time flowmeter employs two transducers, which act as ultrasonic transmitters and receivers. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring clean liquids Power supply: 24VDC/85VAC-2265AC Communication: RS485

Multi-channel ultrasonic flow meter could be manufactured from 50mm~700mm and mainly be used to measure the flow
and heat of clean liquid which don’t contain large concentration of suspended particles or gas.
RS485 communication
Accuracy:¡À0.5%
Flow velocity:0.1~¡À7m/s
Input:Two-wire PT1000
Supporting single channel and multi-channel

For the Doppler Open Channel flow meter, it is a kind of sensor that measures flow velocity and flow rate in natural waters, channels or pipes. Wall-mounted type Doppler Open Channel flow meter consists of a wall-mounted flow calculator and a transducer. The transducer consists of a flow velocity sensor, a water depth sensor of ultrasonic principle, a water depth sensor of pressure principle and a conductivity sensor, which are separately used to measure flow velocity, depth, and conductivity of water in rivers, streams, open channels and pipelines.

Specifications:
Measurement categories: velocity, flow, water depth, water temperature
Level of protection: IP68
Purpose: on-line measurement
Velocity measuring range: the standard is 0.04 m/s ~ 5.00 m/s (the sensor is 20
cm above minimum depth) ;Other velocity range can be customized.
The velocity measurement resolution: 1 mm/s;
Water depth measurements: 0.02 m ~ 10.00 m; Resolution: 2 mm accuracy:
¡À0.5%;
Flow range: 10 L/s ~ 99999999 cubic meters/hour
Power supply: battery, 12 VDC;
Output signal (battery): RS485;
Output signal (external power supply) : 4-20 mA;
4-20 ma output signal content: instantaneous flow rate£»
Cable length between sensor and transmitter: 10 m;
Types of channels subjected to measurement: pipeline, channels, natural stream
and rivers;

Wall Mounted Ultrasonic Flowmeter 25mm water flow meter are used in conjunction with clamp on transducer to accurately measure liquid flow in closed pipes without the need to insert any mechanical parts into the pipe wall or into the fluid inside.
Using ultrasonic transit time technology, controlled by a microprocessor system, it holds a large amount of data, making it available for pipes of almost any material, from 15mm to 6000mm diameter (depending on the sensor model). This series can measure fluids at various temperatures (up to 160¡ãC).
Accuracy: +/-1.0% of FS
Wide range: DN15mm-DN6000mm
Measuring clean liquids
Power supply: 24VDC/85VAC-2265AC
Communication: RS485

Handheld water flowmeter portable ultrasonic clamp on type flow meter is a portable liquid flow measurement device with a sensor. Handheld water flowmeter portable ultrasonic clamp on type flow meter proven transit-time ultrasonic measurement technology for superior accuracy and ease of installation and installation. This easy-to-use flowmeter comes in a rugged, waterproof carrying case for easy transport of the display, sensor, and cables between measurement locations. High accuracy +/-1.0% of FS Transducer temperature: -30~90¡ãC/-30¡ãC~160¡ãC Measuring clean liquids Battery-powered,for 12 hours Communication: RS232

Q&T wall-mounted ultrasonic flowmeter incorporates the latest ultrasonic technology to give you an accurate, easy to use hybrid flow meter with transit-time operating modes. With their quick and easy clamp-on transducer installation, factory pre-configuration and user programmable menu driven interface, the ultrasonic flow meters are a snap to commission in the field. The reliable Q&T wall-mounted ultrasonic flowmeter use custom algorithms and technology to ensure high accuracy flow metering.
Accuracy: +/-1.0% of FS
Wide range: DN15mm-DN6000mm
Measuring single clean liquids
Power supply: 24VDC/85VAC-2265AC
Storage: SD card optional
Heat meter optional

Portable Hand Held Ultrasonic Flow Meter are widely used in tap water, heating, water conservancy, metallurgy, chemical industry, machinery, energy and other industries. Portable Hand Held Ultrasonic Flow Meter can be used for production monitoring, flow verification, temporary detection, flow inspection, water meter balance debugging, heat network balance debugging, and energy-saving monitoring. Measuring accuracy: +/-1.0% of FS Transducer temperature: -30~90¡ãC/-30¡ãC~160¡ãC Measuring clean liquids Battery-powered,for 12 hours Communication: RS232

Digital Ultrasonic flowmeter river water type ultrasonic flowmeter is a high precision no-cut tube measurement method. This special design includes matching sensors for ease of use and is ideal for installation in existing systems Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring single clean liquids Power supply: 24VDC/85VAC-2265AC Storage: SD card optional Heat meter optional

DN80 pipe ultrasonic flowmeter water liquid ultrasonic clamp on type is an ultrasonic flowmeter used to measure the flow rate of liquids in closed pipes. The transducer is clamp-on type, which will provide the benefits of contamination-free operation and ease of installation. The transit time flowmeter includes two transducers, which act as ultrasonic transmitters and receivers. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring clean liquids Power supply: 24VDC/85VAC-2265AC Communication: RS485

QTDS-100H handheld ultrasonic flow sensor with output oil flow meter is a portable liquid flow measurement device with a sensor. QTDS-100H handheld ultrasonic flow sensor with output oil flow meter Price, Digital ultrasonic flowmeters with S2 transducers measurement technology for superior accuracy and ease of installation and installation. This easy-to-use flowmeter comes in a rugged, waterproof carrying case for easy transport of the display, sensor, and cables between measurement locations. High accuracy +/-1.0% of FS Transducer temperature: -30~90¡ãC/-30¡ãC~160¡ãC Measuring clean liquids Battery-powered,for 12 hours Communication: RS232

Ultrasonic Flow meter for applications in clean water and in low conductivity media. Operating principle based on transit time measurement.
High Isolation voltage,Strong anti-interference,Suppress voltage noise,Good isolation performance
Inline ultrasonic flow meter collect temperature signal and accuracy reach 0.001¡æ
When using inline ultrasonic flow meter to measure,allowing pipe with liner
Szie:DN15~DN6000
Accuracy:¡À1.0 %
Viscosity:0.1~¡À10m/s
Output:4~20mA,Pulse,OCT,RS485
Power supply:DC24V and AC220V
Connection way:Flange type

wall-mounted digital display industrial ultrasonic flow meter sea water ultrasonic flowmeter consists of two parts: a transmitter unit and a transducer. Magnetic external clamps on the sensor are easy to install and connect to metal tubing for continuous flow measurement. It is especially suitable for on-site flow measurement of various pressure requirements. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring clean liquids Power supply: 24VDC/85VAC-2265AC Communication: RS485