rotameter for water hydraulic oil flow meter water rotameter small metal acid resistant flow meter acrylic rotameter

The metal rotor flowmeter has the characteristics of simple structure, reliable operation, wide application range, accurate measurement and convenient installation. Divided into field indication type and electric remote transmission type, common type flow sensor, instrument material is (1Cr18Ni9Ti), anti-corrosion type is (1Cr18Ni9Ti) lined with PTEF. If the medium measured by the metal rotameter contains ferromagnetic particles, a magnetic filter should be installed at the inlet of the flowmeter. Its material should be the same as the corresponding flowmeter.

Variable Are Meters are an excellent all stainless steel Inline Flow Meter suitable for many liquids with its wide flow range from 2 lt/min up to 650 lt/min. The robust construction, pressure rating and suitability for corrosive applications makes this quality meter an excellent choice for many process applications that require flow indication.
Range ratio: 10:1(Special type 20:1).
Accuracy class: 2.5(Special type 1.5% or 1.0%).
Working pressure: DN15~DN50 PN16 (Special type 2.5MPa).
Medium temperature: Normalized type -80¡æ~+220¡æ.
Ambient temperature: -40¡æ~+120¡æ(Remote display without LCD¡Ü85¡æ).

The metal rotor flowmeter has the characteristics of simple structure, reliable operation, wide application range, accurate measurement and convenient installation. Install a magnetic filter at the entrance. Its material should be the same as the corresponding flowmeter. Metal tube rotameter has been widely used in petrochemical, steel, electric power, metallurgy, light industry, food, pharmaceutical, water treatment and other industries due to its excellent performance and reliability, as well as good performance-price ratio.

Variable area flow meter Series are used for measure instantaneous and accumulated flow rate of liquid, gas and steam in closed pipelines. It is suitable for metering flow value on site or electronic remote. The measuring principle is based on the hydrodynamic effects,This makes float moving from bottom to top in vertical Pipe. As the displacement of float is in related to flow rate, which can be read from the indicator by means of the magnetic drive system in non-contact form . Also, flowmeters output electrical signal (4-20)mA / hart communication protocol with high / low limit Warning switches/integrating flow PCB broad can be configured.
Range ratio: 10:1(Special type 20:1).
Accuracy class: 2.5(Special type 1.5% or 1.0%).
Working pressure: DN15~DN50 PN16 (Special type 2.5MPa).
Medium temperature: Normalized type -80¡æ~+220¡æ.
Ambient temperature: -40¡æ~+120¡æ(Remote display without LCD¡Ü85¡æ).

metal tube rotameter (metal rotameter) consists of two parts: sensor
(measuring tube and float) and signal transmitter (indicator). There are four kinds of liquid contact materials of the sensor: stainless steel, Hastelloy, titanium and stainless steel lined PTFE. Users can select different liquid contact materials
Range ratio:10:1(Special type 20:1)
Accuracy class:2.5(Special type 1.5% or 1.0%)
Working pressure:?DN15~DN50 PN16MPa (Special type 25MPa).
DN80~DN150 PN10MPa (Special type 16MPa).?Pressure rating of jacket 1.6MPa.
Output:4~20mA/?HART?/RS485?/Alarm?/Pulse
Connection mode:Flange Thread Tri-clamp

Metal tube rotameter is a variable area flow measurement instrument commonly used in industrial automation process control. It has the characteristics of small size, large detection range and convenient use. It can be used to measure the flow of liquid, gas and steam, and is especially suitable for the measurement of low flow rate and small flow. Metal tube rotameter has been widely used in petrochemical, steel, electric power, metallurgy, light industry, food, pharmaceutical, water treatment and other industries due to its excellent performance and reliability, as well as good performance-price ratio.

The intelligent metal tube float flow meter is a variable area flow meter based on the float position measurement. It adopts all-metal structure, has the characteristics of small size, small pressure loss, large range ratio (10~20:1), optional transmitter with HART communication function, convenient installation and maintenance, etc. It is widely used in complex and harsh environments in various industries. It is suitable for flow measurement and process control of small flow, low flow rate, and various harsh media conditions.

The metal rotor flowmeter has a simple structure, no moving parts, and is not easy to be worn by the fluid. The working performance is stable, reliable and has a long service life; Low loss, ideal for high-precision flow measurement. It is a kind of flow measuring instrument commonly used in industrial automation process control. It has the characteristics of small pressure loss, large detection range (range ratio 10:1), and easy to use. It can be used to measure the flow of liquid, gas and steam. It is especially suitable for Low flow rate and small flow medium flow measurement.

Metal Cone Variable Area Flowmeters Are Used For Measure Instantaneous And Accumulated Flow Rate Of Liquid, Gas And Steam In Closed Pipelines. It Is Suitable For Metering Flow Value On Site Or Electronic Remote. The Measuring Principle Is Hydrodynamic Effects,This Makes Float Moving From Bottom To Top As The Displacement Of Float Is In Related To Flow Rate, Which Can Be Read From The Indicator By Means Of The Magnetic Drive System In Non-Contact Form . Also, Flowmeters Output Electrical Signal (4-20)MA / Hart Communication Protocol With High / Low Limit Warning Switches/Integrating Flow PCB Broad Can Be Configured

The metal tube rotameter is a variable area flow meter based on the float position measurement, which is especially suitable for the measurement of gas and liquid flow with low flow rate and small flow. The metal tube float adopts an all-metal structure and a Modular concept design. It has the characteristics of small volume, small pressure loss, large range ratio, and convenient installation and maintenance. Therefore, it is widely used in complex and harsh environments in various industries. Flow measurement and process control for harsh media conditions.

Matel tube flowmeter based on the float principle are versatile and can be used for conductive and non-conducting liquids and gases. The sturdy all-metal design ensures high resistance to pressure, temperature and media and stands up to extreme application and environmental conditions.
Range ratio:10:1(Special type 20:1)
Accuracy class:2.5(Special type 1.5% or 1.0%)
Working pressure:?DN15~DN50 PN16MPa (Special type 25MPa).
DN80~DN150 PN10MPa (Special type 16MPa).
Pressure rating of jacket 1.6MPa.
Output:4~20mA/?HART?/RS485?/Alarm?/Pulse
Connection mode:Flange Thread Tri-clamp

The float of the metal rotameter is in the measuring tube. With the change of flow, the float moves up, and the buoyancy of the float and the gravity of the float reach a balance at a certain position. At this time, the flow annulus area between the float and the orifice plate (or cone tube) remains constant. The area of the annular gap is proportional to the rising height of the float, that is, the rising position of the float in the measuring tube represents the flow rate, and the position of the changing float is transmitted by the internal magnet to the external indicator, so that the indicator can correctly indicate the flow value at this time. . This makes the indicator housing not in direct contact with the measuring tube, so even if a limit switch or transmitter is installed, the instrument can be used under high temperature and high pressure working conditions. It is a variable area flow measuring instrument commonly used in industrial automation process control. It has the characteristics of small size, large detection range and convenient use. It can be used to measure the flow of liquid, gas and steam, especially suitable for medium flow measurement with low flow rate and small flow.

Metal rotameter is a variable area flow measurement instrument commonly used in industrial automation process control. It has the characteristics of small size, large detection range and convenient use. It can be used to measure the flow of liquid, gas and steam. It is especially suitable for medium flow measurement with low flow rate and small flow.

metal tube rotameter/ variable area flow meter is suitable for aggressive fluids measurement. It is a traditional and classic flow metering technology which is used in many applications in industry for monitoring the medium flow rate. This rugged flow meter can be used to measure caustic soda, hydrofluoric acid, sulfuric acid and so on.
Range ratio: 10:1(Special type 20:1).
Accuracy class: 2.5(Special type 1.5% or 1.0%).
Working pressure: DN15~DN50 PN16 (Special type 2.5MPa).
Medium temperature: Normalized type -80¡æ~+220¡æ.
Ambient temperature: -40¡æ~+120¡æ(Remote display without LCD¡Ü85¡æ).

The metal tube rotameter adopts 304/316 stainless steel structure, which can be used to measure the flow of liquid, gas, and steam. It is especially suitable for low measurement of low flow rate, micro flow range, high temperature, high ressure, corrosive, conductive or non-conductive medium.
Range ratio:10:1(Special type 20:1)
Accuracy class:2.5(Special type 1.5% or 1.0%)
Working pressure:?DN15~DN50 PN16MPa (Special type 25MPa).
DN80~DN150 PN10MPa (Special type 16MPa).?Pressure rating of jacket 1.6MPa.
Output:4~20mA/?HART?/RS485?/Alarm?/Pulse
Connection mode:Flange Thread Tri-clamp

Metal tube rotameter is a kind of variable area flow measuring instrument commonly used in automatic process control of I industry. It has the characteristics of small size, large detection range and convenient use. It can be used to measure the flow of liquids, gases and steam. It is especially suitable for medium flow measurement with low flow rate and small flow. Metal tube rotameter has local display type and intelligent remote transmission type, supports a variety of output protocols, provides users with a very broad choice space, various excellent performance and reliability of metal tube rotameter, and better performance. Cost-effective, widely favored by petrochemical, steel, metallurgical light industry, food, pharmaceutical, water treatment and other industries.

metal rotameter mainly used in liquid, acid ,or gas flow measurement and automatic control system in the oil, chemical, pharmaceutical, food and other industries.
Range ratio:10:1(Special type 20:1)
Accuracy class:2.5(Special type 1.5% or 1.0%)
Working pressure:?DN15~DN50 PN16MPa (Special type 25MPa).
DN80~DN150 PN10MPa (Special type 16MPa).
Pressure rating of jacket 1.6MPa.
Output:4~20mA/?HART?/RS485?/Alarm?/Pulse
Connection mode:Flange Thread Tri-clamp

The metal tube high temperature rotameter flowmeter has the advantage of small volume and convenient operation.It is a kind of variable area flow quantity measuring instrument.Ithas various such as field indication type,intelligent remote transmission type,corrosionresistan type,clamped type and damping type.lt can measure the flow of the media with small flow velocity and small flow quantiy.
Range ratio:10:1(Special type 20:1)
Accuracy class:2.5(Special type 1.5% or 1.0%)
Working pressure:?DN15~DN50 PN16MPa (Special type 25MPa).
DN80~DN150 PN10MPa (Special type 16MPa).?Pressure rating of jacket 1.6MPa.
Output:4~20mA/?HART?/RS485?/Alarm?/Pulse
Connection mode:Flange Thread Tri-clamp

Metal tube float flowmeter is based on the float position measuring a variable area flow meter, adopts full metal structure, the concept of Modular design, because of its small size small pressure loss, large range than (10:1), installation, maintenance is convenient wait for acharacteristic
Range ratio:10:1(Special type 20:1)
Accuracy class:2.5(Special type 1.5% or 1.0%)
Working pressure:?DN15~DN50 PN16MPa (Special type 25MPa).
DN80~DN150 PN10MPa (Special type 16MPa).?Pressure rating of jacket 1.6MPa.
Output:4~20mA/?HART?/RS485?/Alarm?/Pulse
Connection mode:Flange Thread Tri-clamp

The tube rotameter is a variable area flow measuring instrument, which consists of a measuring tube, a float, an indicator, and a process connection. For continuous measurement of volumetric flow of liquids and gases in closed pipes. The metal tube rotameter has the characteristics of firm and reliable structure, wide temperature range, high precision, low price, and can be used for flow measurement in various occasions. This series is an on-site intelligent indication type, and a remote signal transmission type is optional. There are three installation forms: bottom in, top out, left in and right out, and bottom in and side out. It is widely used in liquid and gas flow measurement in chemical, petroleum, metallurgy, electric power, environmental protection, medicine and light industry sectors

rotameters measure flow rate of a liquid or gas by relating linear displacement of an internal ¡°float¡± or sharp-edged orifice tube to a corresponding flow rate. Variable Area meters either allow flow through a peripheral orifice formed between a tapered wall and a float as in the traditional rotameter, or an annular orifice and an internal tapered metering pin in the Device Head. The attributes of the Variable Area flow meter are a linear relationship between flow rate, pressure differential and piston displacement. Flow rate is read on the Variable Area meters in both Analog or Digital Display by aligning the position of the piston/float to an adjacent calibrated scale.

The flow measurement of the metal rotameter is performed by the transmitter in the indicator by coupling the porcelain steel to feel the change of the float position to complete the flow indication and the remote transmission of the signal. When the measured medium flows through the measuring tube from bottom to top, when the float is balanced by gravity, buoyancy and the vertical upward driving force of the fluid velocity on the float, the float is relatively stationary at a certain position, and this position varies with the distance between the float and the vertebral canal. The ring area and fluid velocity vary, and the position of the float corresponds to the flow rate of the measured medium.

Metal tube rotameter is a kind of variable area flow measure ment instrument commonly used in industrial automation pro- cess control. It has the characteristics of small volume, large detection range, reliable operation, small maintenance, long service life and convenient use.
Range ratio:10:1(Special type 20:1)
Accuracy class:2.5(Special type 1.5% or 1.0%)
Working pressure:?DN15~DN50 PN16MPa (Special type 25MPa).
DN80~DN150 PN10MPa (Special type 16MPa).?Pressure rating of jacket 1.6MPa.
Output:4~20mA/?HART?/RS485?/Alarm?/Pulse
Connection mode:Flange Thread Tri-clamp

A rotameter is an industrial flowmeter used to measure the flowrate of liquids and gases. The rotameter consists of a tube and float. The float response to flowrate changes is linear, and a 10-to-1 flow range or turndown is standard. In the case of OMEGA? laboratory rotameters, far greater flexability is possible through the use of correlation equations. The rotameter is popular because it has a linear scale, a relatively long measurement range, and low pressure drop. It is simple to install and maintain.
Range ratio: 10:1(Special type 20:1).
Accuracy class: 2.5(Special type 1.5% or 1.0%).
Working pressure: DN15~DN50 PN16 (Special type 2.5MPa).
Medium temperature: Normalized type -80¡æ~+220¡æ.
Ambient temperature: -40¡æ~+120¡æ(Remote display without LCD¡Ü85¡æ).

Metal tube rotameter with the transmitter is also called digital rotameter. All-metal structure, there are indicator type, electric remote transmission type, corrosion-resistant type, high voltage type, jacket type, explosion-proof type.
Electric remote transmission, explosion-proof design. Explosion-proof mark Exd ¢ò CT6. Optional HART protocol function. DC24V power supply, the on-site pointer indicates instantaneous flow. Digital display instantaneous and cumulative flow. Two-wire system 4¡«20mA output. There are 4 buttons on the panel to view and modify internal parameters.

Metal tube rotameter is Widely used in petrochemical, steel, electric power,
metallurgy, light industry, food, pharmaceutical,
water treatment and other industries
Range ratio:10:1(Special type 20:1)
Accuracy class:2.5(Special type 1.5% or 1.0%)
Working pressure:?DN15~DN50 PN16MPa (Special type 25MPa).
DN80~DN150 PN10MPa (Special type 16MPa).
Pressure rating of jacket 1.6MPa.
Output:4~20mA/?HART?/RS485?/Alarm?/Pulse
Connection mode:Flange Thread Tri-clamp

large range ratio (10:1), convenient installation and maintenance, it is
widely used in flow measurement and process control of small flow rate,
low flow rate and various harsh medium conditions in various industries
and harsh environments
Range ratio:10:1(Special type 20:1)
Accuracy class:2.5(Special type 1.5% or 1.0%)
Working pressure:?DN15~DN50 PN16MPa (Special type 25MPa).
DN80~DN150 PN10MPa (Special type 16MPa).
Pressure rating of jacket 1.6MPa.
Output:4~20mA/?HART?/RS485?/Alarm?/Pulse
Connection mode:Flange Thread Tri-clamp

metal tube rotameter is a kind of measuring meter in which the flow rate is
changing along with the area and is widely used in the process control of industrial automation.
It has the merit of lttle volume, broad measuring range, and convenience for use. It can be used to measure liquid, gas, and vapor flow especially fits for the flow rate measurement of low flow velocity and little flow rate.
Range ratio: 10:1(Special type 20:1).
Accuracy class: 2.5(Special type 1.5% or 1.0%).
Working pressure: DN15~DN50 PN16 (Special type 2.5MPa).
Medium temperature: Normalized type -80¡æ~+220¡æ.
Ambient temperature: -40¡æ~+120¡æ(Remote display without LCD¡Ü85¡æ).

The remote type metal tube rotameter can be used in flow measurement and process control in complex, harsh environments and various medium conditions, and is suitable for measuring liquids and gases. Especially suitable for small diameter and low flow rate medium flow measurement; widely used in: chemical industry, power generation, food, water treatment, etc. In the process of flow measurement in complex, harsh environmental conditions, and various medium conditions.

The Metal Tube Rotameter uses the variable area measurement principle. The intelligent metal tube float flowmeter has a local display type and an intelligent remote transmission type, with the transmitter. Metal Tube Rotameter can be used to measure the flow of liquid, gas, and steam. It is especially suitable for medium flow measurement with a low flow rate and small flow.
Range ratio: 10:1(Special type 20:1).
Accuracy class: 2.5(Special type 1.5% or 1.0%).
Working pressure: DN15~DN50 PN16 (Special type 2.5MPa).
Medium temperature: Normalized type -80¡æ~+220¡æ.
Ambient temperature: -40¡æ~+120¡æ(Remote display without LCD¡Ü85¡æ).