Remote 5 Meters Non Contact Ultrasonic Water Fuel Tank Level Sensor

The magnetic flap level gauge is equipped with upper and lower limit switch outputs to realize remote alarm and limit control.
The magnetic flap level Transmitter is equipped with a transmitter, which can realize the remote indication, detection and control of the liquid level. According to the different installation positions of the container, there are two types of side mounting and top mounting.
Measuring range: 300¡«15000mm
Measurement accuracy: ¡À5mm or ¡À10mm
Working pressure: 1.0, 1.6, 2.5, 4.0, 6.4 ,10,16.0MPa
Working temperature: ¡Ü550¡æ
Medium viscosity: ¡Ü0.02Pa.S
Output signal: two-wire system 4¡«20mADC or HART protocol or four-wire system 485 digital output
Explosion-proof grade: Exdll CT6
Protection level: IP66

QTLM series Ultrasonic level transmitter adopt the time of flight measuring principle, widely used for liquid, slurry and solid level tank. 4-20mA ultrasonic level sensor adopt advanced clamp type terminal, to ensure that wiring never loose and remains accurate.

Level Range:4-30m
Sensor:ABS/PVC/PTFE
Output: 4-20mA/HART
Power:DC24V
Accuracy:0.5%

Emission frequency: 76GHz~81GHz
Measurement range:0.1 m ~30m
Measurement accuracy: ¡À1mm
Beam angle: 6¡ã
Power supply range: 9~24 VDC
Communication mode: TTL/NB/485
Operating temperature: -40~85¡æ
Housing material: Aluminum alloy
Antenna type: Lens antenna

Higher signal-to-noise ratio, almost unaffected by level fluctuations;
The measurement accuracy is millimeter-level accuracy (1mm), which can be
used for metrology-level measurement;
The measurement blind area is small (3cm), and the effect of measuring the liquid
level of small storage tanks is better.

76-81 GHZ frequency modulation wave FMCW radar products (also called a millimeter wave radar), because it USES higher than Ku band radar frequency millimeter wave band, the remote target detection, strong smoke dust environment.

Q&T PTFE Liquid Level Sensor PVDF Sensor ultrasonic level transmitter is a digital level meter with high- performance microprocessor to process signals; It meets the requirements of material level without the contact. It can be widely used for level measurement of municipal river, urban groundwater level, sewage treatment station, water works, etc.

Specifications:
Measuring Range: liquid: 0.2-30 m
Process Connection: G2 Thread/ M95*2.0
Energy Transducer Material: ABS, PVC, PTFE
Temperature: -40~ 75 Deg C
With automatic Temperature compensation.
Process Pressure: ¡À 0.1MPa
Precision: 0.2% of actual range
Signal output: 4-20mA (Option:HART)
Power Supply: DC20V~32V ¡Ý30mA
Mode of Indication: 4 Digit LCD

QTLM series Non contact ultrasonic level meters are field-proven for more than thousands of applications in water and waste water field. QTLM Non contact ultrasonic level meters provide continuous level measurement up to 30meter. Q&T support OEM service in colour design, packing etc.

QTLM series Ultrasonic level meter no moving parts, and it can measure level without making physical contact with the object. This typical characteristic of the transmitter is useful for measuring levels in tanks with corrosive, boiling and hazardous chemicals. The accuracy of the reading remains unaffected even after changes in the chemical composition or the dielectric constant of the materials in the process fluids.QTLM series Ultrasonic level meter Widely Used Solutions. Consistently Accurate Results.
Level Range:4-30m
Sensor:ABS/PVC/PTFE
Output: 4-20mA/HART
Power:DC24V
Accuracy:0.5%

QTLM Ultrasonic fuel tank level sensor is a ideal device for high accuracy, continuous level measurement of a wide variety liquid applications. Ultrasonic level meter could make in compact or remote type, with loop powered transmitter and various output signals support to connect with user control system.
Range:4-30m
Application:Liquid / Solid
Sensor: ABS/PVC/PTFE
Output:4-20mA/HART
Power:DC24V
Accuracy:0.5%

Non contact ultrasonic level meter is a recommend choice for different level applications which require low cost, non-contact level measurement. QTLM Ultrasonic level meters are with the ability of being easily connected into control systems.
Range:4-30m
Application:Liquid / Solid
Sensor: ABS/PVC/PTFE
Output:4-20mA/HART
Power:DC24V
Accuracy:0.5%

This Milk level 4-20mA output Liquid Ultrasonic Tank Level Gauge is used to measure the water,beverage or chemical liquid level. This ultrasonic level transmitter has been widely used on food industry, sewage plants, channel, river level monitoring etc.

Specifications:
Measuring Range: liquid: 0.2-30 m
Process Connection: G2 Thread/ M95*2.0
Energy Transducer Material: ABS, PVC, PTFE
Temperature: -40~ 75 Deg C
With automatic Temperature compensation.
Process Pressure: ¡À 0.1MPa
Precision: 0.2% of actual range
Signal output: 4-20mA (Option:HART)
Power Supply: DC20V~32V ¡Ý30mA
Mode of Indication: 4 Digit LCD

QTLM ultrasonic level sensor emits ultrasonic pulses in the direction of the medium,which support various connections like thread or flange connection type which is much easier for user.QTLM series Ultrasonic level transmitter have full-screen self-illumination,easy setting and debugging of liquid level measurement, support 4-20mA two wire output, which is widely used in water, fuel tank, food tank, solid level application.
Level Range:4-30m
Sensor:ABS/PVC/PTFE
Output: 4-20mA/HART
Power:DC24V
Accuracy:0.5%

Magnetic Level Gauges provides direct, high clarity indication of liquid level. Magnetic level gauge are now widely used in all industries as they avoid direct contact with indicator system;
Measuring range: 300¡«15000mm
Measurement accuracy: ¡À5mm or ¡À10mm
Working pressure: 1.0, 1.6, 2.5, 4.0, 6.4 ,10,16.0MPa
Working temperature: ¡Ü550¡æ
Medium viscosity: ¡Ü0.02Pa.S
Output signal: two-wire system 4¡«20mADC or HART protocol or four-wire system 485 digital output
Explosion-proof grade: Exdll CT6
Protection level: IP66

This 4-20mA output PTFE Liquid Level Sensor Q&T Beer Milk level Meter is used to measure the water,beverage or chemical liquid level. This ultrasonic level transmitter has been widely used on food industry, sewage plants, channel, river level monitoring etc.

Specifications:
Measuring Range: liquid: 0.2-30 m
Process Connection: G2 Thread/ M95*2.0
Energy Transducer Material: ABS, PVC, PTFE
Temperature: -40~ 75 Deg C
With automatic Temperature compensation.
Process Pressure: ¡À 0.1MPa
Precision: 0.2% of actual range
Signal output: 4-20mA (Option:HART)
Power Supply: DC20V~32V ¡Ý30mA
Mode of Indication: 4 Digit LCD

QTLM ultrasonic level transmitter all input and output lines must be with such protection functions as lightning protection ,use the time of flight measuring principle and short circuit prevention,it adopt Advanced since the clamp type terminal, to ensure that wiring never loose.
QTLM Liquid tank level sensor wave spread speed among gas is influenced by gas temperature, When level meter works, it measures gas temperature needing, compensates for the velocity of sound, so as to ensure the precision of measuring.

Level Range:4-30m
Sensor:ABS/PVC/PTFE
Output: 4-20mA/HART
Power:DC24V
Accuracy:0.5%

Small beam angle , the energy can be concentrated, enhance the ability of echo and to avoid interference.
Antenna is in small size,easy to install.
A shorter wavelength, the reflection of solid surface inclination is better.
Good working performance in serious dust solid environment.
Smaller measuring blind area,measuring result will be more accurate.
No corrosion,no pollution,friendly to human and environment

Frequency: 76GHz ~ 81GHz, 5GHz FMCW bandwidth
Measuring range: 0.3 m ~ 60m
0.08m~30m
0.6m ~ 120m
Measurement accuracy: ¡À1mm
Beam angle: 3¡ã/8¡ã
Power: 15~28VDC
Communication: MODBUS
HART/Series
Signal output: 4 ~ 20mA or RS-485

Process pressure£º-0.1~0.5MPa
Measurement accuracy£º¡À1mm
Protection class£ºIP67
Explosion-proof grade£ºExib II CT6 Gb
Shell material£ºCast aluminum/stainless steel
Signal output£º4-20mA, HART (two-wire, four-wire), RS485 Modbus

Ultrasonic level tank meter is made up of ABS or PTFE probe which is with acid and alkali resistance. QTLM ultrasonic level meter could be safety installed in complex environments. Support various different connection ways like thread or flange connection.
Range:4-30m
Application:Liquid / Solid
Sensor: ABS/PVC/PTFE
Output:4-20mA/HART
Power:DC24V
Accuracy:0.5%

Magnetic level gauge work on the principle of buoyancy, the float moves up and down with the rise and fall of the liquid level in the measuring tube, therefore the level in the measuring chamber will be the same as the level in the silo/vessel. The measuring chamber is fitted with a float, which has a magnet inside.
Measuring range: 300¡«15000mm
Measurement accuracy: ¡À5mm or ¡À10mm
Working pressure: 1.0, 1.6, 2.5, 4.0, 6.4 ,10,16.0MPa
Working temperature: ¡Ü550¡æ
Medium viscosity: ¡Ü0.02Pa.S
Output signal: two-wire system 4¡«20mADC or HART protocol or four-wire system 485 digital output
Explosion-proof grade: Exdll CT6
Protection level: IP66

QTLM ultrasonic level sensor emits the ultrasonic wave to measure the distance by measuring the time between the wave emission and reception.The sensor fully enclosed probe,improve the intensity of the transmitted signal,integrated casting,good long-term stability.

Level Range:4-30m
Sensor:ABS/PVC/PTFE
Output: 4-20mA/HART
Power:DC24V
Accuracy:0.5%

Ultrasonic fuel tank level sensor adopt ultrasonic technology is a good choice for level applications that require low cost, non-contact liquid slurry and solid level measurement. Especially for sewage treatment, paper pulp, urban water supply etc.
Ultrasonic level transmitter support 4-20mA two wire and HART communication, which is very convenient for customer’s application.
Range:4-30m
Output:4-20mA/HART
Connection:Thread/Flange
Power:DC24V
Accuracy:0.5%
Protection:IP65

Measuring Range: 70m
Frequency Range: 26GHz
Output: 4-20mA/HART
Accuracy: ¡À15mm
Process Pressure: -0.1 ~ 4 MPa
Housing material: Stainless Steel
Process connectio: Flange

Ultrasonic level transmitters are with the feature of non-contact and maintenance-free, a cost-effective and reliable solution for liquid, solid level measurments. QTLM ultrasonic level meters are with humanized LCD show window which is easy to debug, observe and installed conveniently.
Range:4-30m
Application:Liquid / Solid
Sensor: ABS/PVC/PTFE
Output:4-20mA/HART
Power:DC24V
Accuracy:0.5%

QTLM series Ultrasonic level meter is a non-contact, high reliability, cost-effective, easy to install and maintain level measurement instruments and easily configured by menu button and could give precision and accuracy for real-time measurement. the new generation ultrasonic level meter is developed through our company¡¯s many years¡¯ efforts and our company own the completely independent property rights of it.
Level Range:4-30m
Sensor:ABS/PVC/PTFE
Output: 4-20mA/HART
Power:DC24V
Accuracy:0.5%

Frequency Range£º76~81GHz
Scope of application£ºStrong corrosive liquid level, stirring, water vapor condensation
Measuring range£º120m
Process connection£ºflange, thread
Medium temperature£º-40~120¡æ

Process pressure£º-0.1~0.5MPa
Measurement accuracy£º¡À1mm
Protection class£ºIP67
Explosion-proof grade£ºExib II CT6 Gb
Shell material£ºCast aluminum/stainless steel
Signal output£º4-20mA, HART (two-wire, four-wire), RS485 Modbus

QTLM ultraonic level sensor ideal for high-accuracy, continuous level measurement of a wide variety of liquids in storage and shipping containers requiring a non-contact measurement solution,widely used for liquid, slurry and solid level tank.QTLM ultraonic level meter measuring range up to 30 m.Easy and flexible mounting combined with high chemical compatibility.
Level Range:4-30m
Sensor:ABS/PVC/PTFE
Output: 4-20mA/HART
Power:DC24V
Accuracy:0.5%

Q&T Magnetic Level Gauge can be used to measure the liquid level of kinds of vessels in the shapes of water tower, kettle, groove and ball as well as boiler furnace. It can be used under highsealing, leak prevention, high pressure, high temperature and corrosion condition, which is safe and reliable. It makes up for the deficiency of fuzzy instruction and fragility of the glass plate level gauge.
Measuring range: 300¡«15000mm
Measurement accuracy: ¡À5mm or ¡À10mm
Working pressure: 1.0, 1.6, 2.5, 4.0, 6.4 ,10,16.0MPa
Working temperature: ¡Ü550¡æ
Medium viscosity: ¡Ü0.02Pa.S
Output signal: two-wire system 4¡«20mADC or HART protocol or four-wire system 485 digital output
Explosion-proof grade: Exdll CT6
Protection level: IP66

Process pressure£º-0.1~0.5MPa
Measurement accuracy£º¡À1mm
Protection class£ºIP67
Explosion-proof grade£ºExib II CT6 Gb
Shell material£ºCast aluminum/stainless steel
Signal output£º4-20mA, HART (two-wire, four-wire), RS485 Modbus