Q&T Solar Power wastewater open channel measurement flow system

Not affected by water quality, the ultrasonic open channel flowmeter can be equipped with a communication interface, which is easy to connect with SCADA systems to achieve industrial remote monitoring and control. This Open Channel flow meter measures level, flow rate and total volume of water flowing through weirs, flumes, and channels etc.

Specifications:
Sensor?Level?Range: 0-4.0m; other?level?range?also?available
Blind?zone: 0.20m
Temperature?Compensation: Integral?in?probe
Pressure?Rating: 0.2MPa
Beam?Angle: 8*?(3db)
Cable?Length: 10m?standard?(can?be?extended?to?1000m)
Sensor?Material: ABS,?PVC?or?PTFE?(optional)
Sensor?Protection Class: IP68

Ultrasonic flow measurement according to the ¡°differential transit time¡± method: This method uses two sensors, set opposite each other in the measuring tube. Each sensor can alternately transmit and receive ultrasonic signals, while simultaneously measuring the signal transit time.
Bi-directional flow measurement
Backlit LCD
Measuring up to 100 times/s
Accuracy:¡À0.5%

Q&T 4-20mA output Open Channel flow meter measures level, flow rate and total volume of water flowing through weirs, flumes and channels. The flow meters use a non-contact level sensor. Application field£ºWater and sewage treatment£ºpump room, collection well, biochemical reaction
tank, sedimentation tank. And Electricity, mines£ºmortar pool, coal slurry pool, butter storage tank, stockyard or some mobile equipment control etc. And Food industry£ºwineries, granaries, storage tanks for food materials, etc.

Specifications:
Display: Backlight?LCD
The?maximum?of Accumulative Flow: 9999999.9?m3/h
Resolution: 1mm
Analogue?Output: 4-20mA
Relays?Output: Standard?2?relay?outputs(Optional?up?to?6?relays)
Serial?Communication: RS485,?MODBUS RTU
Ambient?Temperature: -40 ~70 Degree C
Power?Supply: DC24V, AC 220V£»Optional?DC12V

PLCM series ultrasonic open channel ultrasonic flow meter can directly display the instantaneous and cumulative flow, it is good for waster water measuring also a good river flow meter. The product supports weirs or notches of different standards in various countries and can be widely used for measurement or monitoring of total water drainage. The measurement result is not affected by the water quality.
Sensor Level Range: 0-4.0m; other level range also available
Blind zone: 0.20m
Temperature Compensation: Integral in probe
Pressure Rating: 0.2MPa
Beam Angle: 8* (3db)
Cable Length: 10m standard (can be extended to 1000m)
Sensor Material: ABS, PVC or PTFE (optional)
Sensor Protection Class: IP68

QINGTIAN ultrasonic flow meter offer better performance and wide turn-down ratio and non-intrusive sensors that can be installed without cutting into the pipe or stop production. Linearity:±1%;
Pipe size:1″ to 48″ (25mm to 1200mm).Pipe size under 1″ is an option;
Fluid:Water or others;
Flow range:± 0.09ft/s ~ ±16ft/s (±0.03m/s ~ ±5m/s);
Outputs:Analog output:4~20mA,max load 750Ω,Pulse output: 0~10KHz;

With ultrasonic flow meters, the flow of liquids can be measured reliably – independent of conductivity, pressure, temperature, and in applications where traceability and guaranteed accuracy are required, the external ultrasonic sensor is the first choice. Clamp-on ultrasonic sensors, on the other hand, are mounted on the outer wall of the pipe and can therefore also be used for temporary measurements.
Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring clean liquids Built-in rechargeable battery 3.6V Communication: RS232

OEM DN15-DN6000 China Wall Mounted Ultrasonic Water Flowmeter is a portable liquid flow measurement device with a sensor. This 2-inch clamp-On Ultrasonic Flow Meterutilizes proven transit-time ultrasonic measurement technology for superior accuracy and ease of installation and installation. This easy-to-use flowmeter comes in a rugged, waterproof carrying case for easy transport of the display, sensor, and cables between measurement locations. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring single clean liquids Power supply: 24VDC/85VAC-2265AC Storage: SD card optional Heat meter optional

This Open Channel Water Meters consists of two elements, a host, which has display and an integral keypad for programming, and a transducer/probe, which must be mounted directly above the surface to be measured. It can be widely applied to the environmental protection, water treatment, irrigation, chemical, and other industries.

Specifications:
Display: Backlight?LCD
Flow?Rate?Range: 0.0000~99999L/S?or?m3/h
The?maximum?of Accumulative Flow: 9999999.9?m3/h
Accuracy?of?Change in Level: 1mm?or?0.2%?of?full?span?(whichever?is?greater)
Resolution: 1mm
Analogue?Output: 4-20mA,?corresponding?to?instantaneous?flow
Relays?Output: Standard?2?relay?outputs(Optional?up?to?6?relays)
Serial?Communication: RS485,?MODBUS?-RTU?standard?protocol

Ultrasonic water clamp on sensor module flow meter consists of two parts: a transmitter unit and a transducer. Magnetic external clamps on the sensor are easy to install and connect to metal tubing for continuous flow measurement. It is especially suitable for on-site flow measurement of various pressure requirements. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring clean liquids Power supply: 24VDC/85VAC-2265AC Communication: RS485

Inline ultrasonic flow meter could connect temperature sensor to become one calorimeter and widely
be used in Process control, Production measurement, Trade settlement and is suitable for continuously measuring flow and heat of clean and uniform liquids without large concentration suspended particles or gases industrial environment¡£
Support single channel and multi-channel at the same time,when one of channel is abnormal or not connected,it can automatically switch to single channel to working .

This irrigation flow meter is a professional economic and practical instrument during agriculture, industry research and development. It is a non-contact measurement and can be applied in even harsh environments. This Open channel Irrigation flow meter can directly display the instantaneous and cumulative flow.
Power Supply: DC24V (+5%) 0.2A; AC220V (+20%) 0.1A ;Optional DC12V
Flow Rate Range: 0.0000~99999L/S or m3/h
The maximum of Accumulative Flow:  9999999.9 m3/h
Analogue Output: 4-20mA, corresponding to instantaneous flow
Relays Output: Standard 2 relay outputs(Optional up to 6 relays)
Serial Communication: RS485, MODBUS -RTU standard protocol
Ambient Temperature: -40 ~70 Degree C

Q&T Wall mounted ultrasonic flowmeter clamp on type transducer is a high precision no-cut tube measurement method. This special design includes matching sensors for ease of use and is ideal for installation in existing systems Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring single clean liquids Power supply: 24VDC/85VAC-2265AC Storage: SD card optional Heat meter optional

Ultrasonic flow meter is one kind of water flow meter which accuracy less than 1.0%
Flange type ultrasonic flow meter no moving parts, no wear, no pressure loss,Maintenance-free and can measure conductivity liquid and Non-conductivity liquid.
2 way analogy input could transmit flow,pressure,temperature,pressure etc

Clamp on flow meter sensor portable ultrasonic flowmeter, no pipe cutting required. This is very different from traditional flow devices. The user simply clamp on the flow sensor to the pipe surface. ThePortable handheld ultrasonic flowmeter clamp on water flowmeter can then detect the flow through ultrasonic waves, and then automatically calculate the flow rate value, flow accumulator, etc. No pipe cutting means no damage to the pipe. So as long as the pipes are in good condition, the installation on the flowmeter will not provide the possibility of leakage. This advantage is more suitable for strong acid, strong alkali, poisoning, corrosive liquid, etc. Sensor: Clamp-on/External Principle: transmit time Size: DN15mm-DN6000mm Measuring medium: Liquid 3.6V Battery-powered

Multi-channel ultrasonic flow meter is suitable for continuously measuring flow and heat of clean and uniform liquids without large concentration particles or gases under industrial environment.
Ultrasonic flow meter can measure water,Seawater,Acid solution,Cooking oil,Gasoline,Coal oil,Diesel,Alcohol,
Beer and other uniform liquid could transmitting ultrasonic waves.

Flange ultrasonic flow meter could be manufactured from 50mm~700mm and mainly be used to measure the flow and heat of clean liquid which don’t contain large concentration of suspended particles or gas.

Digital Wall Mounted Clamp on Ultrasonic Flowmeter Flow Meter is simple to install and is suitable for large diameter pipes requiring monitoring and flow measurement, as well as a wide network of smaller supply linesDigital Wall Mounted Clamp on Ultrasonic Flowmeter Flow Meter provide the tools needed to meet the diverse requirements of such a demanding industry. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring clean liquids Power supply: 24VDC/85VAC-2265AC Communication: RS485

RS232 3.6V Lithium Battery Digital Water Handheld Ultrasonic Flow Meter is a non-contact instrument, which can measure the flow of medium with large diameter and can also be used for the measurement of medium that is not easy to contact and observe. Digital Water Handheld Ultrasonic Flow Meter measurement accuracy is very high, and it is hardly disturbed by various parameters of the measured medium. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Medium: clean liquids,pure water Built-in rechargeable battery 3.6V Housing Material: ABS

Insertion type ultrasonic flow meters allow measurement of pipes that are not compatible with the clamp-on type,like the cement pipe etc,fixed type ultrasonic flow meter also use for large pipe. Repeatability:0.2% of measured value;
Linearity:±1%;
Pipe size:1″ to 48″ (25mm to 1200mm).Pipe size under 1″ is an option;
Fluid:Water or others;
Flow range:± 0.09ft/s ~ ±16ft/s (±0.03m/s ~ ±5m/s);

QT621 portable type ultrasonic clamp on flow meters use clamp-on transducers that are mounted externally on the surface of the pipe and which generate pulses that pass through the pipe wall.
Portable ultrasonic flow meters are widely applicated from simple water flow measurements to energy flow monitoring and automated process control.

Size: 1¡å~48¡å(25mm~1200mm)
Flow Range:¡À0.01 m/s~ ¡À12 m/s
Accuracy: ¡À1%
Repeatability: 0.2%
Output: 4-20mA, RS485
Power supply: Internal lithium 3000mAh
Transducer: IP68

Drinking water flowmeter ultrasonic clamp on type flowmeter is a portable liquid flow measurement device with a sensor. This Drinking water flowmeter ultrasonic clamp on type flowmeter proven transit-time ultrasonic measurement technology for superior accuracy and ease of installation and installation. This easy-to-use flowmeter comes in a rugged, waterproof carrying case for easy transport of the display, sensor, and cables between measurement locations. High accuracy +/-1.0% of FS Transducer temperature: -30~90¡ãC/-30¡ãC~160¡ãC Measuring clean liquids Battery-powered,for 12 hours Communication: RS232

Highest Quality Handheld ultrasonic flow meter & Solutions, ultrsonic flow meter is a ideal for liquids such as chemical,visous liquids, and sea water. The non-intrusive, clamp-on ultrasonic flow meter fits pipes between 1/2″ to 48″ internal diameter. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Medium: clean liquids,pure water Built-in rechargeable battery 3.6V Measurment unit: Meter, Feet,Cubic Meter.

QT621 ultrasonic water flow meter support is widely used in oil industry, water treatment, pure water, chemical and etc. Adopt the technology of transit time, ultrasonic waves transmitted and received through moving liquid. The difference between upstream and downstream transit time can be used to calculate flow and velocity.

Size: 1¡å~48¡å(25mm~1200mm)
Flow Range:¡À0.01 m/s~ ¡À12 m/s
Accuracy: ¡À1%
Repeatability: 0.2%
Output: 4-20mA, RS485
Power supply: Internal lithium 3000mAh
Transducer: IP68

This Waste Water open Channel flow meter has wide application, good for applications such as groundwater system flow
monitoring, industrial sewage discharge monitoring, flow into water treatment plants, effluent from water resource recovery, and
agriculture irrigation channels.

Specifications:
Display: Backlight?LCD
Flow?Rate?Range: 0.0000~99999L/S?or?m3/h
The?maximum?of Accumulative Flow: 9999999.9?m3/h
Accuracy?of?Change in Level: 1mm?or?0.2%?of?full?span?(whichever?is?greater)
Resolution: 1mm
Analogue?Output: 4-20mA,?corresponding?to?instantaneous?flow
Relays?Output: Standard?2?relay?outputs(Optional?up?to?6?relays)
Serial?Communication: RS485,?MODBUS?-RTU?standard?protocol

Multi-channel ultrasonic flow meter is suitable for continuously measuring flow and heat of clean and uniform liquids without large concentration suspended particles or gases industrial environmen.
Support single channel and multi-channel at the same time,when one of channel is abnormal or not connected,it can automatically switch to single channel to working .
Dual channel
Heat measurement
Bi-directional flow measurement

The open channel flow meter level sensor is mounted on the top of the flume, and ultrasonic wave is transmitted by the probe to the surface of the monitored material. Instead of using mass or volumetric data to determine the rate of flow of a substance, open channel flow meters monitor the relationship between the depth of the liquid and the flow rate.

Specifications:
Sensor?Level?Range: 0-4.0m; other?level?range?also?available
Blind?zone: 0.20m
Temperature?Compensation: Integral?in?probe
Pressure?Rating: 0.2MPa
Beam?Angle: 8*?(3db)
Cable?Length: 10m?standard?(can?be?extended?to?1000m)
Sensor?Material: ABS,?PVC?or?PTFE?(optional)
Sensor?Protection Class: IP68

China wall mounted Clamp on pipe ultrasonic water flow meter price provide you with an accurate, easy-to-install flow meter. wall mount flow sensor feature quick, easy clamp-on sensor installation, configuration, and a user-programmable menu-driven interface for easy commissioning in the field. China wall mounted Clamp on pipe ultrasonic water flow meter price use a special algorithm and technology to ensure highly accurate flow measurement. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring single clean liquids Power supply: 24VDC/85VAC-2265AC Storage: SD card optional Heat meter optional

QTDS-100H Sea Water Ultrasonic Flowmeter incorporates the latest ultrasonic technology to give you an accurate, easy to use hybrid flow meter with transit-time operating modes. With their quick and easy clamp-on transducer installation, factory pre-configuration and user programmable menu driven interface, the ultrasonic flow meters are a snap to commission in the field. The reliable QTDS-100H Sea Water Ultrasonic Flowmeter use custom algorithms and technology to ensure high accuracy flow metering.
Accuracy: +/-1.0% of FS
Wide range: DN15mm-DN6000mm
Medium: clean liquids,pure water
Built-in rechargeable battery 3.6V
Communication: RS232

Ultrasonic clamp-on flow meter is simple to install and is suitable for large diameter pipes requiring monitoring and flow measurement, as well as a wide network of smaller supply lines. Ultrasonic clamp-on flow meter provide the tools needed to meet the diverse requirements of such a demanding industry. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring clean liquids Power supply: 24VDC/85VAC-2265AC Communication: RS485

This Factory Ultrasonic water flow meters are perfect for wastewater applications, leak-proof structure and IP68 protect grade; Q&T ultrasonic open channel flow meter Measure level, flow rate and total volume flow.
Display: Backlight LCD
The maximum of Accumulative Flow: 9999999.9 m3/h
Accuracy of Change in Level: 1mm or 0.2% of full span (whichever is greater)
Resolution: 1mm
Analogue Output: 4-20mA, corresponding to instantaneous flow
Relays Output: Standard 2 relay outputs(Optional up to 6 relays)
Serial Communication: RS485, MODBUS -RTU standard protocol
Ambient Temperature: -40 ~70 Degree C
Power Supply: DC24V (+5%) 0.2A; AC220V (+20%) 0.1A ;Optional DC12V