QT natural gas compensation commercial gas turbine flow meter

Turbine Flow Meter is a volumetric measuring turbine type of Impeller Flow meters , made up of Sensor and Convertor. The flowing fluids engages the rotor causing it to rotate at an angular velocity proportional to the fluid flow rate.The Sensor reacts to the average velocity of fluid with multi-blades rotor so as to speculating the flow value and the accumulative flow value.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%;
OUTPUT: PULSE+4-20mA;
Digital Communication:RS485, MODBUS; HART
LCD display

A turbine flowmeter is a flowmeter that uses a turbine for measurement. It first converts the flow rate to the speed of the turbine. And then converts the speed into an electrical signal that is proportional to the flow.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%;
OUTPUT: PULSE+4-20mA;
Digital Communication:RS485, MODBUS; HART

QTWG series wide turndown gas turbine flow meters are custody transfer approved flow meters, widely used in clean gas including natural gas, LPG gas etc. Q&T gas turbine flow meters are well manufactured and tested in factory which could ensure exact values for fiscal and non-fiscal measurements.?
Size:DN25-400mm
Material:Aluminum alloy or stainless steel
Dual Power:3.6V battery powered+DC24V
Output:4-20mA,Pulse,RS485
Accuracy:1.5% or 1.0%

turbine flow transducer adapts to measure the liquid rate and total flowrate of low viscosity. It can be widely used in the fields of Petrol, Chemical industry, Metallurgy, Scientific research for measuring or control. Several output and display methods can be selected.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%;
OUTPUT: PULSE+4-20mA;
Digital Communication:RS485, MODBUS; HART

turbine flow meter refers to the turbine flow sensor with 50mm size. DN50 turbine flow meter can be used to take volumetric flow measurement of petroleum, organic liquid, biogas, LPG gas, liquefied gas, natural gas, hydrocarbon gas, nitrogen, cryogenic fluid, water, diesel, High-pressure hydraulic oil, methanol and other non-impurity, non-corrosive. 2 inch turbine flow meter has many applications in turbine heating systems, boilers measurement of water supply, heat exchange system, air conditioning circulating water, etc.

Turbine Flow Meter is a volumetric measuring turbine type of Impeller Flowmeters, made up of sensors and Convertor. The flowing fluids engage the rotor causing it to rotate at an angular velocity proportional to the fluid flow rate. The Sensor reacts to the average velocity of fluid with the multi-blades rotor so as to speculating the flow value and the accumulative flow value
liquid turbine flow meter is a volumetric metering the meter consists of a rotor and bearing assembly Suspended on a shaft, which is mounted to a support device.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%/¡À0.2%;
OUTPUT: PULSE/4-20mA;
Digital Communication:RS485, MODBUS; HART

QTWG series natural gas flow meters offer high quality measurement solution for clean gas which could increase efficiency in gas transmission, distribution and industrial applications. Turbine gas meters are with lightweight and compact body and support a wide range of measurement including maximum working pressure and maximum measuring flow rate.
Size:DN25-400mm
Material:Aluminum alloy or stainless steel
Dual Power:3.6V battery powered+DC24V
Output:4-20mA,Pulse,RS485
Accuracy:1.5% or 1.0%

turbine flow meters are used for the precise measurement of instantaneous flow rates of low-viscosity fluids such as tap and demineralized water, fuels, liquefied gases, light fuel oils, solvents, and pharmaceutical fluids. Turbine flowmeters measure volumetric flow, where fluid passing through the meter body is measured by the mean velocity of the flowing fluid media. Flow rectifiers ensure a laminar flow in the axial direction of the wheel. A low-mass turbine wheel carried concentrically within the meter body is rotated by the fluid. The RPM of the turbine wheel is directly proportional to the mean flow rate within the meter body and directly corresponds to the volumetric flow over a wide range.

QTWG turbine gas flow meters are ideal flow measurement device for clean gas, including natural gas, LPG gas etc. Turbine gas meters are with lightweight in compact body and support a wide range of measurement including maximum working pressure and maximum measuring flow rate.
Size:DN25-400mm
Material:Aluminum alloy or stainless steel
Dual Power:3.6V battery powered+DC24V
Output:4-20mA,Pulse,RS485
Accuracy:1.5% or 1.0%

Turbine flow sensor is a precision flow measuring instrument, which can be used to measure the flow and total amount of liquid together with the corresponding flow totalizer. It is widely used in metering and control systems in petroleum, chemical, metallurgy, scientific research and other fields. Turbine flow sensors with sanitary fittings can be used in the pharmaceutical industry.
The structure of the integrated turbine flowmeter is explosion-proof and can display the total flow, instantaneous flow and percentage of full flow. The battery adopts long-term lithium battery. The battery life of the single-function accumulator can reach more than 5 years, and the battery life of the multi-function display watch can also reach more than 12 months.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%/¡À0.2%;
OUTPUT: PULSE/4-20mA;
Digital Communication:RS485, MODBUS; HART

Liquid Turbine Flow Meter with a 4-20 mA output available in 12 sizes covering flow ranges between 0.176 to 880 GPM. Turbine Flow Meters are designed to meet the demands of the most rigorous flow measurement applications. The meter features a 304 stainless steel housing and rotor support, CD4MCU stainless steel rotor, and abrasion-resistant tungsten carbide rotor shaft and 316SS bearings. These materials help the meter to maintain accuracy and mechanical integrity when measuring the corrosive and abrasive fluids found in many industries

The turbine flow meter is an ideal solution when high accuracy, compact size, fast response, and high tolerance to shock and vibration are critical requirements and suitable for wide range of viscosity medium including oil, gas, water and wastewater, chemical, gas utility, power, food and beverage, aerospace, pharmaceutical, etc.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%/¡À0.2%;
OUTPUT: PULSE/4-20mA;
Digital Communication:RS485, MODBUS; HART

QTWG series turbine gas meters are designed to measure natural gas, air, nitrogen, carbon dioxide, propane vapor, and other non-corrosive gases accurately. Q&T LPG gas turbine flow meter with the features of cost-effective, widely used for gas transmisstion and some other industry.
Size:DN25-400mm
Material:Aluminum alloy or stainless steel
Dual Power:3.6V battery powered+DC24V
Output:4-20mA,Pulse,RS485
Accuracy:1.5% or 1.0%

A turbine flow meter is a volume sensing device. As liquid or gas passes through the turbine housing, it causes the freely suspended turbine blades to rotate. The velocity of the turbine rotor is directly proportional to the velocity of the fluid passing through the flow meter.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%;
OUTPUT: PULSE+4-20mA;
Digital Communication:RS485, MODBUS; HART

Turbine flowmeter installation
Normally turbine flow meter has flange, thread, clamp-on connections, and the fluids direction should be the same as the arrow on the meter body. The liquid turbine flow sensor can be installed horizontally and vertically, and the fluid direction must be upward when installed vertically.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%/¡À0.2%;
OUTPUT: PULSE/4-20mA;
Digital Communication:RS485, MODBUS; HART

turbine flow meter having a mechanical section combined with electronic board displaying the flow rate, the end connection of which is finished with a flange. Because its driving part is mechanical, it can be applied for all fluids of low temperature to high temperature with relatively high accuracy and excellent reproducibility.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%/¡À0.2%;
OUTPUT: PULSE/4-20mA;
Digital Communication:RS485, MODBUS; HART

liquid turbine flow meter is a new generation turbine flow meter which was designed with advanced flow technologies both home and aboard. The product possesses advantages of simple structure, light in weight, high accuracy, good repeatability, short response time, easy installation, etc. It could be used widely in measurement of closed pipe system for pure liquid that will not react with 1Cr18Ni9Ti, 2Cr13, Al2O3 and hard alloys.

QTWG series natural gas flow meter is used to measure gas flow, with the features of high accuracy, low-pressure drop. Wide turndown gas turbine flow meter is custody transfer approval flow meter, widely used in clean gas including natural gas, LPG gas etc.
Size:DN25-200mm
Material:Aluminum alloy or stainless steel
Dual Power:3.6V battery powered+DC24V
Output:4-20mA,Pulse,RS485
Installation: Vertical or Horizontal
Accuracy:1.5% or 1.0%

Turbine Flow Meter is a main type of Impeller Flowmeter also including the Anemoscope and Water meter. it is made up of Sensor and Conversion-Show. The Sensor reacts to the average velocity of fluid with multi-blades rotor so as to speculating the flow value and the accumulative flow value. The velocity (or circles) of rotor can be picked up by the way of mechanism, electromagnetic induction, photo electricity, before displaying and transmitting the records by reading device.

Turbine flow meters measure the velocity of liquids, gases and cryogenic fluids. Typical fluids and gases measured with turbine flowmeters include hydrocarbons, chemicals, water, cryogenic liquids, air, natural gas and industrial gases.Apure turbine flowmeters are easy to operate and maintain. For this reason, Apure turbine flowmeters can be used worldwide and are considered a reliable, cost-effective way to achieve high-precision flow measurements
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%/¡À0.2%;
OUTPUT: PULSE/4-20mA;
Digital Communication:RS485, MODBUS; HART

A turbine flowmeter is a flowmeter that uses a turbine for measurement. It first converts the flow rate to the speed of the turbine. And then converts the speed into an electrical signal that is proportional to the flow. Turbine flow meter is used to detect the instantaneous flow and the total accumulated flow. And its output signal is frequency, which is easy to digitize.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%;
OUTPUT: PULSE+4-20mA;
Digital Communication:RS485, MODBUS; HART

QTWG Turbine gas meter is a popular device for gas-fired, gas pipeline network and city gas field etc. QTWG turbine gas meters are very reasonably priced with good reliability and quality. With the features of low pressure loss, high accuracy, low initiating flow, anti vibration and pulsation flow resistance etc.
Size:DN25-400mm
Material:Aluminum alloy or stainless steel
Dual Power:3.6V battery powered+DC24V
Output:4-20mA,Pulse,RS485
Accuracy:1.5% or 1.0%

turbine flow meter adapts to measure the liquid rate and total flowrate of low viscosity. It can be widely used in the fields of Petrol, Chemical industry, Metallurgy, Scientific research for measuring or control. Several output and display methods can be selected.

QTWG series explosion proof turbine gas meters are widely used for gas-fired, gas pipeline network, and city gas field etc.Turbine gas meters offer high capacity ability for various custody transfer applications, with the features of low pressure loss, high accuracy and good anti-vibration.
Size:DN25-400mm
Material:Aluminum alloy or stainless steel
Dual Power:3.6V battery powered+DC24V
Output:4-20mA,Pulse,RS485
Accuracy:1.5% or 1.0%

QTWG turbine gas meter is a type of high-precision custody transfer metering. As a ideal flow measurement device for natural gas or other non-corrosive gases applications, gas turbine flow meter urbine could be automatically pressure and temperature compensation to obtain volumetric measurements in standard units.

Size:DN25-400mm
Material:Aluminum alloy or stainless steel
Dual Power:3.6V battery powered+DC24V
Output:4-20mA,Pulse,RS485
Accuracy:1.5% or 1.0%

QTWG series turbine gas meters are with the features of low pressure loss, high accuracy and good anti-vibration. Widely used for gas-fired, gas pipeline network, and city gas field etc, turbine gas meters offer high capacity ability for various custody transfer applications,

Size:DN25-400mm
Material:Aluminum alloy or stainless steel
Dual Power:3.6V battery powered+DC24V
Output:4-20mA,Pulse,RS485
Accuracy:1.5% or 1.0%

Liquid turbine flow meter having a mechanical section combined with electronic board displaying the flow rate, the end connection of which is finished with a flange. Because its driving part is mechanical, it can be applied for all fluids of low temperature to high temperature with relatively high accuracy and excellent reproducibility.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%/¡À0.2%;
OUTPUT: PULSE/4-20mA;
Digital Communication:RS485, MODBUS; HART

QTWG series gas turbine flow meters adopt import impeller material which could ensure high accuracy in working life. Designed to perform on the high level of accuracy, turbine gas flow meters are ideal product for commercial and industrial uses.

Size:DN25-400mm
Material:Aluminum alloy or stainless steel
Dual Power:3.6V battery powered+DC24V
Output:4-20mA,Pulse,RS485
Accuracy:1.5% or 1.0%

turbine flowmeter advantage
1.High accuracy, generally up to ¡À1%R, ¡À0.5%R, high accuracy up to 0.2%R
2.Good repeat-ability, short-term repeat-ability up to 0.05% ~ 0.2%, in the trade settlement is the preferred choice of flow meter.
3.Output of pulse frequency signal, suitable for totalizer and connection with PC; no zero shift and strong interference resist
4.High frequency signal(3~4KHz) can be obtained, the signal resolution is strong.
5.Wide range, medium and large diameter up to 1:20, small caliber 1:10.

turbine flow meter is available in a wide range of body sizes and styles to suit liquid flow applications for low to medium viscosity fluids.
The principle of operation is based on a permanent magnet contained within a pick-off coil on the body and a ferritic stainless steel rotor which revolves when flow is present. A small AC voltage is generated in the coil as the rotor tip passes the magnet. The frequency of this AC voltage is directly proportional to the flow rate. The total number of pulses produced represents the total flow passed through the meter.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%/¡À0.2%;
OUTPUT: PULSE/4-20mA;
Digital Communication:RS485, MODBUS; HART