Profibus PA protocol ¡À0.5% accuracy liquid flow meter

waste water flow meter is calibrated by MT methoud water flow standard calibration device, mass method, comparison method and pulse method can be used, standard accuracy is ±0.5%, ±0.2% accuracy is optional. magnetic flow meter is calibration equipment 5 points flow meter, mass method, comparison method and pulse method can be used

Repeatability: 0.17%
Electrode: SUS316L, Hastelloy B, Hastelloy C
Structure: compact, remote
Liner: PTFE, PFA, Polyurethane, Neoprene, Hard Rubber, Ceramic
Output Signal: 4~20 mA, Pulse

magnetic heat meter can be configured yellow or green OLED display, SD card or GPRS to monitor history record, bluetooth is convenient to check flow. our calibration lab has been approved CNAS ISO/IEC 17025:2017. magnetic flow meter is configured with PTFE and SS316L electrodes, with compact or remote type structurer,

Electrode: SUS316L, Hastelloy B, Hastelloy C
Structure: compact, remote
Liner: PTFE, PFA, Polyurethane, Neoprene, Hard Rubber, Ceramic
Output Signal: 4~20 mA, Pulse
Communication: RS485, HART, PROFIBUS

Battery power electromagnetic flowmeter service life with 5 years, battery flowmeter fulfills the special customer demands to water application with distribution network as well as irrigation. Nominal Pressure: 0.6-1.6MPa(2.5Mpa / 4.0Mpa /6.4Mpa…Max 42Mpa); Accuracy: ¡À0.5% (Standard), ¡À0.3% or ¡À0.2% (Optional); Measuring Range: Max 15m/s; Conductivity: >5us/cm; Protection Class: IP65(Standard),IP68(Optional for remote type); Output Signal: 4-20mA / pulse (optional); Communication: RS485(Optional),HART(Optional),GPRS/GSM(Optional); Power Supply: Battery powered 3.6V,Battery powered 3.6V +DC24V(Optional);

slurry version electromagnetic flow meters Electromagnetic flowmeter consists of sensors and converters in two parts. The product is based on Faraday’s law of electromagnetic induction, used to measure the conductance greater than 20 μS / cm
● Power Supply : AC85~250V, DC20V~36V
● Power Consumption :<20W ● Communication : RS485/Modbus,Hart,Profitbus ● Display : LC Display,128X128mm Three lines 4 internal push buttons ● Ambient Temperature:-20℃~60℃ ● Relative Humidity : 5%~95% ● Liner Material :Neoprene(Rubber) PTFE PFA F46 Polyurethane ) ● Velocity : 0.1 m/s ~ 15 m/s ● Explosion-proof : Exd IIB T6 Gb ● Nominal Pressure : 4.0 MPa (DN3-DN150)

Q&T series electromagnetic flow meters are flow totalizing meters that can be used to provide rate flow and totalized flow of various liquids such as water, polymers, surfactants and other chemicals. These meters are non-invasive electromagnetic meters designed for harsh applications and long life with excellent accuracy. there are no moving parts through the entire measuring chamber and accuracy is increased while maintenance requirements are decreased. The entire flow chamber consists of a PTFE liner to ensure absolute chemical compatibility with most all known chemicals.

Size: 1/8″-120″
Accuracy: ±0.5%
Electrode: SUS316L, Hastelloy B, Hastelloy C
Structure: compact, remote
Liner: PTFE, PFA, Polyurethane, Neoprene, Hard Rubber, Ceramic
Output Signal: 4~20 mA, Pulse
Communication: RS485, HART, PROFIBUS
Protection Grade: IP65 std, IP68 optional for remote
Velocity: 0.1~15 m/s
Conductivity: > 5 μS/cm, demineralized water > 20 µS/cm
Power supply: 85~250 VAC, 20V~36VDC, 3.6V lithium battery
Size: DN3-DN3000
Sensor material: carbon steel (std), SS304 / SS316 (optional)
Flange: ANSI, DIN, JIS, etc.
Measuring tube: SS304
Function: High and low alarm, exciting alarm, empty pipe alarm, self-diagnosis

Battery power electromagnetic flow meter with IP68 protection, Battery power magnetic flow meter workable under water for few days, flow meter can add external 12-24 VDC power supply with 4-20mA. Size: DN10-DN2000; Nominal Pressure: 0.6-1.6MPa(2.5Mpa / 4.0Mpa /6.4Mpa…Max 42Mpa); Accuracy: ¡À0.5% (Standard), ¡À0.3% or ¡À0.2% (Optional); Structure: Integral,remote,submersible,ex-proof; Medium Temperature: -20¡æ~+60¡æ (integral type), Remote type(neoprene,Hard rubber,Polyurethane, EPDM) :-10¡æ~+80¡æ; Remote type (PTFE / PFA / FEP): -10¡æ~+160¡æ; Protection Class: IP65(Standard),IP68(Optional for remote type); Output Signal: 4-20mA / pulse (optional); Communication: RS485(Optional), HART(Optional), GPRS/GSM (Optional);

When the water consumption of the measuring point is abnormal or the battery of the field flow meter is insufficient, the system can send an alarm message, and the alarm information can be directly sent to the mobile phone of the user designated by the user.

Q&T Instrument has ISO/IEC 17025:2016 CNAS Approved Test Bench for ¡À0.2% Accuracy.

inline magnetic flow meter is calibrated on ¡À0.2% calibration device, so accuracy of electromagnetic flowmeter can be up to ¡À0.2%. the magnetic flow meter is configured 4~20 mA, pulse and RS485 modbus

Process connection of insertion magnetic flowmeter is thread ball valve or flange ball valve, it can be install with pressure. insertion electromagnetic flow meter is used to measure the flow of conductive liquids. insertion magmeter, which allows sensor to be installed and retracted from process piping without shutting down the process. size is from DN100-DN3000

Power supply: 85~250 VAC, 20V~36VDC, 3.6V lithium battery
Size: DN3-DN3000
Sensor material: carbon steel (std), SS304 / SS316 (optional)
Flange: ANSI, DIN, JIS, etc.
Measuring tube: SS304
Function: High and low alarm, exciting alarm, empty pipe alarm, self-diagnosis

mag flow meter will be tested by pressure equipment. magmeter is calibrated by ISO/IEC 17025:2016 CNAS Approved. liquid flow meter is installed in the chemical plant to measure waste water.

Output Signal: 4~20 mA, Pulse
Communication: RS485, HART, PROFIBUS
Power supply: 85~250 VAC, 20V~36VDC, 3.6V lithium battery
Size: DN3-DN3000
Sensor material: carbon steel (std), SS304 / SS316 (optional)
Measuring tube: SS304

Electromagnetic water meter is manufactured with the present up-to-data technology for electromagnetic flowmeter. It has the following characteristics:
The measurement is independent of density, viscosity, temperature, pressure and the change of conductivity of the fluid;

Q&T liquid flow meter including magnetic flow meter, electromagnetic flow meter, magmeter,which is designed to measure various conductive liquids. manufacturer of flow meters and level meters. Founded in 2005, certified ISO 9001:2015
Output Signal: 4~20 mA, Pulse
Communication: RS485, HART, PROFIBUS
Protection Grade: IP65 std, IP68 optional for remote
Velocity: 0.1~15 m/s
Conductivity: > 5 ¦ÌS/cm, demineralized water > 20 ¦ÌS/cm

Signal of electromagnetic flowmeter is 4~20 mA, pulse and RS485, but we also configure GPRS for remote monitoring on platform. 5 points are calibrated. electromagnetic flowmeter is calibrated by Mass Method liquid calibration equipment, Q&T Instrument has large stock fro varous flanges for different flow meters, like magnetic fflow meter, turbine flow meter, thermal mass flow meter, etc.

Output Signal: 4~20 mA, Pulse
Communication: RS485, HART, PROFIBUS
Protection Grade: IP65 std, IP68 optional for remote
Velocity: 0.1~15 m/s
Conductivity: > 5 ¦ÌS/cm, demineralized water > 20 ¦ÌS/cm

The Magnetic Flow Meter has bidirectional measuring system and is installed with three totalizers: forward total volume, reverse total volume and total difference; This digital water flow meter can display forward flow and reverse flow volume, and has multiple outputs: current, pulse, digital communication Modbus, HART etc

Specifications:
Accuracy: 0.20%，0.10%
Medium Temperature: -50…200℃
Nominal pressure: 0…4.0MPa
Material : Measuring tube SS316L; Housing: SS304
Process Connection: Flange, Tri-clamp Connection, Thread
Power supply: 24V DC±5% or 220V AC ± 10% 50Hz
Working condition: Ambient temperature: – 20~60℃
Relative humidity: ≤95%
Protection Grade: IP67
Instrument display: mass flow, volume flow, density, temperature

QTLD/T magnetic flowmeter is mainly used to measure beverage, like milk, beer, wine, etc. its liner is PFA which approved NSF and FDA, we are OEM for some Europmean and Amercial brands. electromagnetic water meter is widely used because less obstruction, cost-effective and accurate measurement. Magnetic water meter don’t have any moving parts to wear down, reducing the need for maintenance or replacement.

Structure: compact, remote
Liner: PTFE, PFA, Polyurethane, Neoprene, Hard Rubber, Ceramic
Output Signal: 4~20 mA, Pulse
Communication: RS485, HART, PROFIBUS
Protection Grade: IP65 std, IP68 optional for remote

Measuring Range :0~12m/s ;
Conductive Ratio of the Medium :5¦Ìs/cm
Medium Temperature : -10¡æ~55¡æ ;
Power Supplied : 3.6V DC in-built Lithium ion battery power supplied , continually working for more than three years.

Electromagnetic flowmeters. Measuring for process management, revenue collection, liquid transportation and energy conservation. water flow meter is widely used because less obstruction, cost-effective and accurate measurement. Magnetic flowmeter don’t have any moving parts to wear down, reducing the need for maintenance or replacement.

Liner: PTFE, PFA, Polyurethane, Neoprene, Hard Rubber, Ceramic
Output Signal: 4~20 mA, Pulse
Communication: RS485, HART, PROFIBUS
Protection Grade: IP65 std, IP68 optional for remote
Velocity: 0.1~15 m/s

Electromagnetic water meter is high reliability flowmeter for measuring the volumetric flow of conductive liquids and slurries in closed conduits.
Electromagnetic water meter use a magnetic field to generate and channel liquid flow through a pipe. It have high accuracy and stability. The battery’s working life is mor than 8 years.

Inline magnetic flowmeter is packaged by wooden case with foam to proect it.

magnetic flow meters are calibrated on ¡À0.2% accuracy test bench, electromagnetic flowmeter is calibrationed 5 points. our calibration lab has been approved CNAS ISO/IEC 17025:2017

Measuring Range :0~12m/s ;
Conductive Ratio of the Medium :5¦Ìs/cm
Medium Temperature : -10¡æ~55¡æ ;
Power Supplied : 3.6V DC in-built Lithium ion battery power supplied , continually working for more than three years.

Application: Outdoor,underground.Especially
Without power supply places.
Battery Powered: 3.6V lithium battery
Communication Interface:RS485
Wireless Communication:GSM¡¢GPRS¡¢CDMAProtection:IP68

Measuring Range :0~12m/s ;
Conductive Ratio of the Medium :5¦Ìs/cm
Medium Temperature : -10¡æ~55¡æ ;
Power Supplied : 3.6V DC in-built Lithium ion battery power supplied , continually working for more than three years.

Q&T Instrument has large stock for varous flanges for different electromagnetic flowmeter, like DIN, ANSI, JIS, etc. PTFE, neoprene liner and other liners are optional, Liner of mag flowmeter has been approved NSF or FDA certificate. it can be used to measure driing water. it has function of high and low alarm, empty alarm, excitation alarm, etc.

Size: DN3-DN3000
Accuracy: ¡À0.5%
Electrode: SUS316L, Hastelloy B, Hastelloy C
Structure: compact, remote
Output Signal: 4~20 mA, Pulse
Communication: RS485, HART, PROFIBUS

Battery operated electromagnetic flowmeter enjoys IP68 protection, battery operated magnetic flowmeter workable under water for few days, flow meter can add external 12-24 V DC power supply. Size: DN10-DN2000; Nominal Pressure: 0.6-1.6MPa(2.5Mpa / 4.0Mpa /6.4Mpa…Max 42Mpa); Accuracy: ¡À0.5% (Standard), ¡À0.3% or ¡À0.2% (Optional); Structure: Integral,remote,submersible,ex-proof; Medium Temperature: -20¡æ~+60¡æ (integral type), Remote type(neoprene,Hard rubber,Polyurethane, EPDM) :-10¡æ~+80¡æ; Remote type (PTFE / PFA / FEP): -10¡æ~+160¡æ; Protection Class: IP65(Standard),IP68(Optional for remote type); Output Signal: 4-20mA / pulse (optional); Communication: RS485(Optional), HART(Optional), GPRS/GSM (Optional);

a non full tube electromagnetic flow meter which can automatically display the instantaneous flow velocityand cumulative flow is composed of converter, flow sensor and level sensor. The user only needs to
enter the diameter of pipe, the non-full pipe flowmeter will automatically calculate the flow rate, and automatically
display the instantaneous flow, total flow, velocity, height, etc. It can measure liquid volume min 10% of full pipe. It is
especially suitable for the needs of municipal rainwater, waste water, sewage discharge and irrigation

Electromagnetic water meter GSM/GPRS remote monitoring management topology diagram 4. This system introduces more humanized management such as data backup, SIM card cost statistics and so on.

High-efficiency magnetic flow meter developed based on technologies that were fostered by our long-time amassed experience and performance records, HC, Ti, Tan and PT-IR are optional, mag flow meter is mainly used to measure conductive liquid, liquid flow meter has compact and remote structurer. our magnetic flow meter have been approved CE-LVD, CE-EMC, ATEX, NSF, tec.mag flowmeter is calibrationed 5 points.

Accuracy: ¡À0.5%
Structure: compact, remote
Output Signal: 4~20 mA, Pulse
Communication: RS485, HART, PROFIBUS
Protection Grade: IP65 std, IP68 optional for remote
Velocity: 0.1~15 m/s

Q&T Instrument have large stock for varous flow meters and level meters, goods can be delivered with in 4 days for regular types.

water flow meter is calibrated by stainless steel liquid test bench, mag flowmeter is calibrationed 5 points. we have 8 sets of liquid flow meter to calibrate mag flowmeter.

China supplied magnetic water meter electromagnetic water meter
Electromagnetic water meter is widely used in iron and steel, electric power, petroleum, chemical industry, coal, metallurgy,Papermaking, water supply and drainage, food, medicine and other industries.

All QTLD transmitters should be test in high and low cabinet, temperature is : -20¡æ ~ 60¡æ for 24 hours.