Partial Filled Pipe Flow Meter Sewage cement electronic ip68 flow meter

Application: Outdoor,underground.
Especially without power supply places.
Battery Powered:3.6v lithium battery
Communication Interface:RS485
Wireless
Communication:GSM¡¢GPRS¡¢CDMA
Protection:lP67

1. Instrument display and output functions are complete, it can display instantaneous flow, flow rate, cumulative flow and other data, and has RS485 interface (optional);
2. With GSM and GPRS wireless data remote transmission function (optional);
3. It has the functions of timing, counting and clocking out of power

QTLD/T tri-clamp / sanitary magnetic flowmeter has been approved FDA, NSF certificate, it’s mainly used to measure beverage like milk, wine, beer, juice, etc. Q&T Instrument has ISO/IEC 17025 2016 CNAS Approved Test Bench for ¡À0.2% Accuracy.magnetic flow meter is calibration equipment 5 points flow meter, mass method, comparison method and pulse method can be used.
Output Signal: 4~20 mA, Pulse
Communication: RS485, HART, PROFIBUS
Power supply: 85~250 VAC, 20V~36VDC, 3.6V lithium battery
Size: DN3-DN3000
Sensor material: carbon steel (std), SS304 / SS316 (optional)
Measuring tube: SS304

Electromagnetic water meters, or magmeters, are comprised of a transmitter and sensor that together to measure flow. The magnetic flow meter¡¯s sensor is placed inline and measures an induced voltage generated by the fluid as it flows through a pipe.
No Moving Parts
RS485 Standard,HART standard is available.
Suitable for Pipes Up to DN300
Pulse, Gprs output
Standard 5 points calibration Included

Electromagnetic flowmeters (mag meters) are volumetric flow meters that take measurements by generating a magnetic field that channels through conductive liquids as they flow through a pipe. As the fluid flows, the voltage electrodes in the pipe wall sense the voltage. The higher the flow rate, the greater the amount of voltage generated. An electronic transmitter then converts these signals to provide flow rate measurements.
Use electromagnetic flowmeters with virtually any conductive liquid, including abrasive slurries, water, wastewater, chemicals, acids, and contaminated fluids. These meters are not compatible with steam, gas, oil, or nonconductive fluids.
Size: 1/8″-120″
Accuracy: ±0.5%
Electrode: SUS316L, Hastelloy B, Hastelloy C
Structure: compact, remote
Liner: PTFE, PFA, Polyurethane, Neoprene, Hard Rubber, Ceramic
Output Signal: 4~20 mA, Pulse
Communication: RS485, HART, PROFIBUS
Protection Grade: IP65 std, IP68 optional for remote
Velocity: 0.1~15 m/s
Conductivity: > 5 μS/cm, demineralized water > 20 µS/cm
Power supply: 85~250 VAC, 20V~36VDC, 3.6V lithium battery
Size: DN3-DN3000
Sensor material: carbon steel (std), SS304 / SS316 (optional)
Flange: ANSI, DIN, JIS, etc.
Measuring tube: SS304

Hart communication electromagnetic flowmeters
Medium temperature:
Integral type : -20℃~60℃
Remote type(Rubber&Polyurethane liner): -10℃~80℃
Remote type (PTFE&PFA&F46 liner): -10℃~160℃
♦ Integrated verification,diagnostic function and empty pipe detection.
♦ Measure forward and reverse direction flows.
♦ Built-in reference electrodes,no need to connect ground ring.

Electromagnetic water meter can be used to measure the volume flow of conductive fluid in a closed pipeline. It is widely applied in the flow measurement and control in the fields of chemical and petroleum industry, metallurgy industry, water and wastewater, agriculture and irrigation, paper making, food and beverage industry and pharmaceutical industry, etc.
Electromagnetic flow meter is used in a variety of industries, water treatment, chemical, food , agriculture, water supply and drainage etc.Providing technical support, choosing flow meters according to different working conditions;

mag flowmeter is calibrated by MT methoud water flow standard calibration device, mass method, comparison method and pulse method can be used, magnetic flow meter is calibrated by standard mass method by high accuracy calibration equipment. standard accuracy is ¡À0.5%, ¡À0.2% accuracy is optional. If conductive media such as cooling water are added to a process,

Size: 1/8″-120″
Accuracy: ¡À0.5%
Structure: compact, remote
Velocity: 0.1~15 m/s
Power supply: 85~250 VAC, 20V~36VDC, 3.6V lithium battery
Sensor material: carbon steel (std), SS304 / SS316 (optional)
Measuring tube: SS304

magnetic water meter has wide measuring range, Q3:Q1 is R400, the flow sensor can be desired to be full bore and reduced bore, while reduced bore don’t need any straight pipe in the upstream and downstream. mag flowmeter is widely used in Sewage Treatment Plant Water Supply project and Steel & Aluminum Industries, Chemical & Fertilizer Industries.

Size: 1/8″-120″
Structure: compact, remote
Liner: PTFE, PFA, Polyurethane, Neoprene, Hard Rubber, Ceramic
Power supply: 85~250 VAC, 20V~36VDC, 3.6V lithium battery
Size: DN3-DN3000
Measuring tube: SS304

Sensor protect grade of split magmeter is IP68, it can be submerged in the water or buried underground.

Q&T series insert type electromagnetic flowmeter is on the basis of pipeline electromagnetic flowmeter developed a kind of new flow meter.
After adopting the technology of pressure opening and pressure installation, the plug-in electromagnetic flowmeter can be installed without stopping water, and can also be installed on cast iron pipes and cement pipes. The successful development of plug – in electromagnetic flowmeter provides a new method for fluid flow measurement.

Size: 1/8″-120″
Accuracy: ¡À0.5%
Electrode: SUS316L, Hastelloy B, Hastelloy C
Structure: compact, remote
Liner: PTFE, PFA, Polyurethane, Neoprene, Hard Rubber, Ceramic
Output Signal: 4~20 mA, Pulse
Communication: RS485, HART, PROFIBUS
Protection Grade: IP65 std, IP68 optional for remote
Velocity: 0.1~15 m/s
Conductivity: > 5 ¦ÌS/cm, demineralized water > 20 ¦ÌS/cm
Power supply: 85~250 VAC, 20V~36VDC, 3.6V lithium battery
Size: DN3-DN3000
Sensor material: carbon steel (std), SS304 / SS316 (optional)
Flange: ANSI, DIN, JIS, etc.
Measuring tube: SS304
Function: High and low alarm, exciting alarm, empty pipe alarm, self-diagnosis

DC3.6V powered electromagnetic flowmeter satisfy water fee calculation with high accuracy, battery water meter is widely used in applications without power grid, can work with solar power supply. Accuracy: ¡À0.5% (Standard), ¡À0.3% or ¡À0.2% (Optional); Ambient Humidity: 5-100%RH (relative humidity); Protection Class: IP65(Standard), IP68(Optional for remote type); Process Connection: Flange(Standard),Wafer,Thread,Tri-clamp etc(optional); Output Signal: 4-20mA / pulse (optional); Communication: RS485(Optional),HART(Optional),GPRS/GSM(Optional); Power Supply: Battery powered 3.6V,Battery powered 3.6V +DC24V(Optional); Power Consumption: 0.5W(Standard),1.5W(with DC24V);

Inline magnetic flowmeter is packaged by wooden case with foam to proect it.

magnetic flow meters are calibrated on ¡À0.2% accuracy test bench, electromagnetic flowmeter is calibrationed 5 points. our calibration lab has been approved CNAS ISO/IEC 17025:2017

Liner with PTFE, Neoprene, PFA, FEP is optional, standard material of sensor material is carbon steel, SS304 or SS316 is optional, waste water flow meter can be customized color and logo, Q&T Instrument is OEM for many European and Amercian brands. warranty is 2 years. electromagnetic flowmeter is volumetric flow meter that measure the flow when conductive liquids move through a magnetic field. mag flowmeters have function of high and low alarm, empty pipe alarm, exciting alarm and self-diagnosis.

Output Signal: 4~20 mA, Pulse
Communication: RS485, HART, PROFIBUS
Protection Grade: IP65 std, IP68 optional for remote
Velocity: 0.1~15 m/s
Conductivity: > 5 ¦ÌS/cm, demineralized water > 20 ¦ÌS/cm

Display of mag flowmeter is LCD, OLED is optional, liner is PTFE or Neorpene, agnetic flow meters (also known as magmeter or electromagnetic flow meters) are cost effective volumetric flow meters that do not have any moving parts. Q&T Instrument was established in 2005, products including mag flowmeter, turbine flow meter, ultrasonic flow meter, thermal mass flow meter, etc. We offer flowmeters with a range of liners, electrodes, and sizes, which can meet various conductive liquids.

Repeatability: 0.17%
Electrode: SUS316L, Hastelloy B, Hastelloy C
Structure: compact, remote
Liner: PTFE, PFA, Polyurethane, Neoprene, Hard Rubber, Ceramic
Output Signal: 4~20 mA, Pulse

QTLD magmeter is available as a Line or Battery powered electromagnetic flow meter which operates on the principle of Faraday¡¯s Law of Electromagnetic Induction. It is NSF approved allowing the 1400C to be used on potable (drinking) water applications. This Inline battery-powered magmeter is specially designed for applications where electricity and power supply availability is unavailable. It provides up to 5 years of battery life, minimizing maintenance and enhancing smart measurements¡¯ productivity in field instruments.

Size: 1/8″-120″
Structure: compact, remote
Liner: PTFE, PFA, Polyurethane, Neoprene, Hard Rubber, Ceramic
Power supply: 85~250 VAC, 20V~36VDC, 3.6V lithium battery
Size: DN3-DN3000
Measuring tube: SS304

Standard cable length or remote or split electromagnetic BTU meter is 10m, max length is 120m, Pt1000 temerature sensor is configured. Magnetic heat meter is composed by transmitter, sensor and PT1000 temperature sensor, which can monitor flow and energy of hot water and cold water, standard configuration of flange and sensor shell is carbon steel, SS304 and SS316L are optional.
Size: 1/8″-120″
Accuracy: ¡À0.5%
Repeatability: 0.17%
Electrode: SUS316L, Hastelloy B, Hastelloy C
Structure: compact, remote

Magmeter magnetic flow meter converts voltage to volumetric flow for a high accuracy solution. Conductive fluid flows through an electromagnetic field and generates a voltage proportional to its velocity
Electromagnetic meters are a leading choice to deliver the performance and precision your applications require. These meters are applicable for all conductive liquids, such as water, acids, alkalis, slurries and many others. Typical applications are monitoring of liquids, filling, dosing and precise measurement in custody transfer
Size: 1/8″-120″
Accuracy: ±0.5%
Electrode: SUS316L, Hastelloy B, Hastelloy C
Structure: compact, remote
Liner: PTFE, PFA, Polyurethane, Neoprene, Hard Rubber, Ceramic
Output Signal: 4~20 mA, Pulse
Communication: RS485, HART, PROFIBUS
Protection Grade: IP65 std, IP68 optional for remote
Power supply: 85~250 VAC, 20V~36VDC, 3.6V lithium battery
Size: DN3-DN3000
Sensor material: carbon steel (std), SS304 / SS316 (optional)
Flange: ANSI, DIN, JIS, etc.

magnetic heat meter can be configured yellow or green OLED display, SD card or GPRS to monitor history record, bluetooth is convenient to check flow. our calibration lab has been approved CNAS ISO/IEC 17025:2017. magnetic flow meter is configured with PTFE and SS316L electrodes, with compact or remote type structurer,

Electrode: SUS316L, Hastelloy B, Hastelloy C
Structure: compact, remote
Liner: PTFE, PFA, Polyurethane, Neoprene, Hard Rubber, Ceramic
Output Signal: 4~20 mA, Pulse
Communication: RS485, HART, PROFIBUS

Electromagnetic water meter is researched and developed for the water treatment industry, which is suitable for various basic applications in water, wastewater and other industries. This type of electromagnetic flowmeter is widely used in the flow measurement of raw water, drinking water, process water and wastewater, etc.
1.Support 12 kinds of flow units(m3/h, L/h, LPM, GPM etc.); LCD liquid crystalbacklight display; Power off display function;
2.The converter can display instantaneous flow, cumulative flow, velocity, volume flow,positive and negative cumulative value, positive and negative cumulative difference.
3.Signal output:Pulse, RS485

1. Can be used for flow measurement of open non-full pipe (round pipe, rectangular pipe or other special-shaped pipe);
2. Can be used for continuous measurement of municipal rainwater, wastewater, sewage discharge and irrigation water pipelines;

Electromagnetic flow meter is a volumetric flow meter that does not have any moving parts. It is ideal for wastewater applications or any dirty liquid which is conductive or water based. Magnetic flow meters are also ideal for applications where low-pressure drop and low maintenance are required.
Communication: RS485, HART, PROFIBUS
Velocity: 0.1~15 m/s
Conductivity: > 5 ¦ÌS/cm, demineralized water > 20 ¦ÌS/cm
Power supply: 85~250 VAC, 20V~36VDC, 3.6V lithium battery

Self-diagnosis fault alarm
GSM data infinitely transmitted
LCD display cumulative flow£¬instanta-
neous flow£¬ flow rate,flow percentage,etc.

Electromagnetic water meter is widely used in Sewage Treatment Plant Water Supply project and Steel & Aluminum Industries, Chemical & Fertilizer Industries. No moving parts, no pressure loss and require very less maintenance.
Size: DN3-DN3000
Output Signal: 4~20 mA, Pulse
Communication: RS485, HART, PROFIBUS
Velocity: 0.1~15 m/s

magnetic flowmeter will be tested by pressure equipment. QTLD waste water flow meter is calibrated by ISO/IEC 17025:2016 CNAS Approved liquid flow meter is installed in the chemical plant to measure waste water, the pipe is PVC, so we configure grounding rings to have better grounding to protect the electromagnetic flow meter.

Output Signal: 4~20 mA, Pulse
Communication: RS485, HART, PROFIBUS
Power supply: 85~250 VAC, 20V~36VDC, 3.6V lithium battery
Size: DN3-DN3000
Sensor material: carbon steel (std), SS304 / SS316 (optional)
Measuring tube: SS304

Battery power electromagnetic flowmeter is an ideal solution for nearly any water manager, Battery power magnetic flowmeter eliminates the need for AC/DC power connection. Size: DN10-DN2000; Protection Class: IP65(Standard),IP68(Optional for remote type); Process Connection: Flange(Standard),Wafer,Thread,Tri-clamp etc(optional); Output Signal: 4-20mA / pulse (optional); Communication: RS485(Optional),HART(Optional),GPRS/GSM(Optional); Power Supply: Battery powered 3.6V, Battery powered 3.6V +DC24V(Optional); Power Consumption: 0.5W(Standard), 1.5W(with DC24V); Alarm: Upper limit alarm / lower limit alarm

Standard cable length of remote magnetic flowmeter is 10m, 120m max. protection grade of sensor is IP68. it can be submered or buried underground.

Battery power mag flowmeter is ideal in process measurement and control, survey, leakage detection, etc.Insertion battery mag meters can be installed in any large size pipeline. Size: DN10-DN2000; Nominal Pressure: 0.6-1.6MPa(2.5Mpa / 4.0Mpa /6.4Mpa…Max 42Mpa); Accuracy: ¡À0.5% (Standard),¡À0.3% or ¡À0.2% (Optional); Liner:PTFE,Neoprene,Hard Rubber,EPDM,FEP, Polyurethane,PFA; Electrode: SUS316L,Hastelloy B, Hastelloy C, Titanium,Tantalum,Platinum-iridium; Protection Class: IP65(Standard),IP68(Optional for remote type); Output Signal: 4-20mA / pulse (optional); Communication: RS485(Optional),HART(Optional),GPRS/GSM(Optional);

Q&T’s magnetic flowmeter battery each set will have well calibrated before leave factory, mag flow meter battery adopt pulse calibration, with weighing method, guarantee the 0.5% accuracy. Accuracy: ¡À0.5% (Standard),¡À0.3% or ¡À0.2% (Optional); Liner: PTFE,Neoprene,Hard Rubber,EPDM,FEP,Polyurethane,PFA; Electrode: SUS316L,Hastelloy B,Hastelloy C,Titanium,Tantalum,Platinum-iridium; Ambient Temperature: -20¡æ~+ 60¡æ; Ambient Humidity: 5-100% RH (relative humidity); Process Connection: Flange(Standard),Wafer,Thread,Tri-clamp etc(optional); Output Signal: 4-20mA/pulse (optional);

With simple structure ,the flow meter is of high reliability without lining in the measuring pipe .
The wide range of the nominal bore is suitable for all the pipe size between DN50 and DN300.