Ultrasonic Open Channel Irrigation Flow Meter

QT621 handheld ultrasonic flow meter support accurate bidirectional and highly dynamic flow measurement
with the non-invasive clamp-on technology. Handheld type ultrasonic flow meter mainly applies for measuring the flow of homogeneous medium fluid in the water injection flow measurement, raw water flow measurement, tap water flow measurement etc.

Size: 1¡å~48¡å(25mm~1200mm)
Flow Range:¡À0.01 m/s~ ¡À12 m/s
Accuracy: ¡À1%
Repeatability: 0.2%
Output: 4-20mA, RS485
Power supply: Internal lithium 3000mAh
Transducer: IP68

Clamp on flow meter sensor portable ultrasonic flowmeter, no pipe cutting required. This is very different from traditional flow devices. The user simply clamp on the flow sensor to the pipe surface. ThePortable handheld ultrasonic flowmeter clamp on water flowmeter can then detect the flow through ultrasonic waves, and then automatically calculate the flow rate value, flow accumulator, etc. No pipe cutting means no damage to the pipe. So as long as the pipes are in good condition, the installation on the flowmeter will not provide the possibility of leakage. This advantage is more suitable for strong acid, strong alkali, poisoning, corrosive liquid, etc. Sensor: Clamp-on/External Principle: transmit time Size: DN15mm-DN6000mm Measuring medium: Liquid 3.6V Battery-powered

Using ultrasonic transit time techniques,Wall Mounted Ultrasonic Water Flowmeter is controlled by a micro-processor system which contains a wide range of data that enables it to be used with pipes with an outside diameter ranging from 15mm up to 1200mm (depending on model) and constructed of almost any material. instrument will also operate over a wide range of fluid temperatures.

Low Cost Handheld Flow Meter Inline Pipe Type Stationary Outdoor Ultrasonic Flow Meters is a portable liquid flow measurement device with a sensor. Low Cost Handheld Flow Meter Inline Pipe Type Stationary Outdoor Ultrasonic Flow Meters adopt transit-time ultrasonic measurement technology for superior accuracy and ease of installation and installation. This easy-to-use flowmeter comes in a rugged, waterproof carrying case for easy transport of the display, sensor, and cables between measurement locations. High accuracy +/-1.0% of FS Transducer temperature: -30~90¡ãC/-30¡ãC~160¡ãC Measuring clean liquids Battery-powered,for 12 hours Communication: RS232

Q&T wall-mounted ultrasonic flowmeter incorporates the latest ultrasonic technology to give you an accurate, easy to use hybrid flow meter with transit-time operating modes. With their quick and easy clamp-on transducer installation, factory pre-configuration and user programmable menu driven interface, the ultrasonic flow meters are a snap to commission in the field. The reliable Q&T wall-mounted ultrasonic flowmeter use custom algorithms and technology to ensure high accuracy flow metering.
Accuracy: +/-1.0% of FS
Wide range: DN15mm-DN6000mm
Measuring single clean liquids
Power supply: 24VDC/85VAC-2265AC
Storage: SD card optional
Heat meter optional

High quality clamp on water ultrasonic flow meter portable ultrasonic flowmeter Water flow meter proven transit-time ultrasonic measurement technology This technology can be used for permanent installations where intrusive flow meters are not economically viable for permanent installations on large pipelines and for all the different process fluids encountered in the network. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring clean liquids Power supply: 24VDC/85VAC-2265AC Communication: RS485

This Open Channel Water Meters consists of two elements, a host, which has display and an integral keypad for programming, and a transducer/probe, which must be mounted directly above the surface to be measured. It can be widely applied to the environmental protection, water treatment, irrigation, chemical, and other industries.

Specifications:
Display: Backlight?LCD
Flow?Rate?Range: 0.0000~99999L/S?or?m3/h
The?maximum?of Accumulative Flow: 9999999.9?m3/h
Accuracy?of?Change in Level: 1mm?or?0.2%?of?full?span?(whichever?is?greater)
Resolution: 1mm
Analogue?Output: 4-20mA,?corresponding?to?instantaneous?flow
Relays?Output: Standard?2?relay?outputs(Optional?up?to?6?relays)
Serial?Communication: RS485,?MODBUS?-RTU?standard?protocol

The PLCM industrial waste water treatment flow meter using transit-time principle, it is an economical ultrasonic flowmeter specifically designed for open channel. Compared with other ultrasonic flow meters on the market, it has the characteristics of high reaction rate, low power consumption and high certainty. At the same time, with non-contact level sensor, it also have the feature of installation simple, easy to use, no need water supply shutdown etc.

Specifications:
Display: Backlight?LCD
Flow?Rate?Range: 0.0000~99999L/S?or?m3/h
The?maximum?of Accumulative Flow: 9999999.9?m3/h
Accuracy?of?Change in Level: 1mm?or?0.2%?of?full?span?(whichever?is?greater)
Resolution: 1mm
Analogue?Output: 4-20mA,?corresponding?to?instantaneous?flow
Relays?Output: Standard?2?relay?outputs(Optional?up?to?6?relays)
Serial?Communication: RS485,?MODBUS?-RTU?standard?protocol

Fixed type clamp on ultrasonic flowmeter with RS485 Modbus flow meter is an ultrasonic flowmeter used to measure the flow rate of liquids in closed pipes. The transducer is a non-contact, clamp-on type, which will provide the benefits of contamination-free operation and ease of installation. The transit time flowmeter employs two transducers, which act as ultrasonic transmitters and receivers. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring clean liquids Power supply: 24VDC/85VAC-2265AC Communication: RS485

Ultrasonic flow meter is designed to measure liquid velicity and flow rate in the pipe.
When install the wall mounted ultrasonic flow meter,user don’t need to cut pipe.Just install the flow trasducer in the surface of pipe.So ultrasonic flow meter is one non-contact instrument.
Pipe size:25~1200mm
Accuracy:±1.0%
Output:4-20mA,RS485
Transducer temperature:-40~80℃
Transducer protect:IP68
Power supply:24VDC
SD card

New Version Protable Ultrasonic Water Flowmeter Price For Sale,Ultrasonic Flow Meter is a portable liquid flow measurement device with a sensor. New Version Protable Ultrasonic Water Flowmeter Price For Sale,Ultrasonic Flow Meter adopt transit-time ultrasonic measurement technology for superior accuracy and ease of installation and installation. This easy-to-use flowmeter comes in a rugged, waterproof carrying case for easy transport of the display, sensor, and cables between measurement locations. High accuracy +/-1.0% of FS Transducer temperature: -30~90¡ãC/-30¡ãC~160¡ãC Measuring clean liquids Battery-powered,for 12 hours Communication: RS232

QT811 ultrasonic flow meter support accurate bidirectional and highly dynamic flow measurement with the non-invasive clamp-on technology. Clamp on small size flow meter is a type of small size instrument for non-invasive, quick flow and energy measurement with clamp-on technology for many types of piping.

Pipe Size:?DN15-DN40mm (1/2¡±~1 1/2¡±)
Flow Range:¡À0.1m/s ~¡À5m/s
Temperature: 0~75¡æ (standard)
Output: 4-20mA, OCT Pulse, RS485
Accuracy:?¡À1% of measured value
Power Supply: DC10-24V

Q&T ultrasonic water flow meter maily be used to measure water and measure repeatability can reach 0.2%.
Clamp on water flow meter which used the transfer time technology,when install the transducer,workers will choose different install method for different size pipe,such as V method,Z method,W method.
Output:4-20mA,RS485
Power supply:24VDC,90~245VAC power is optional
Accuracy:±1.0%
Repeatability:±0.2%

Its unique features, particularly low cost, small size, high performance, local display, make it the ideal choice for industrial automation, processing control, flow meter networking, composing multi-channel, high accuracy flow meter.
Pipe diameter range15mm-6000mm
OutputRS485, OCT, 4-20mA
Working powerThe isolation dc8-36V
DisplayLCD with backlight,2*20 letters
Suitable Temperaturer: -40-160 degrees Celsius
Protection ClassIP65 for main unit,IP68 for sensors
Transducers
Clamp-on type, insertion type,pipeline type optional

This non-contact ultrasonic flow meter that is designed for open channel flow metering working with a flume, weir or any other primary device. Non-contact ultrasonic flow meter require accurate measurement of the surface level of a liquid. A flume, channel or structure which has a known characteristic flow per measured head, together with the measured liquid level, accurately define the flow rate through the system.

Analogue?Output: 4-20mA,?corresponding?to?instantaneous?flow
Relays?Output: Standard?2?relay?outputs(Optional?up?to?6?relays)
Serial?Communication: RS485,?MODBUS?-RTU?standard?protocol
Ambient?Temperature: -40 ~70 Degree C
Measure?Cycle: 1?second?(selectable?2?seconds?)
Power?Supply: DC24V?(+5%)?0.2A;?AC220V?(+20%)?0.1A?;Optional?DC12V

Not affected by water quality, the ultrasonic open channel flowmeter can be equipped with a communication interface, which is easy to connect with SCADA systems to achieve industrial remote monitoring and control.

Specifications:
Sensor?Level?Range: 0-4.0m; other?level?range?also?available
Blind?zone: 0.20m
Temperature?Compensation: Integral?in?probe
Pressure?Rating: 0.2MPa
Beam?Angle: 8*?(3db)
Cable?Length: 10m?standard?(can?be?extended?to?1000m)
Sensor?Material: ABS,?PVC?or?PTFE?(optional)
Sensor?Protection Class: IP68

QT621 ultraonic flow meter portable type is an easy operation instrument for non-invasive, quick flow and energy measurement with clamp-on technology for many types of pipings.
Portable ultrasonic flow meter can be easily moved and installed in different pipes and convenient to carry site to site, which is very convenient for users to monitor the data.

Size: 1¡å~48¡å(25mm~1200mm)
Flow Range:¡À0.01 m/s~ ¡À12 m/s
Accuracy: ¡À1%
Repeatability: 0.2%
Output: 4-20mA, RS485
Power supply: Internal lithium 3000mAh
Transducer: IP68

QT811 clamp on flow meters are suitable for various liquids and compatible with various pipeline materials and sizes. Clamp on flow meter is a type of small size instrument for non-invasive, quick flow and energy measurement with clamp-on technology for many types of piping. With support for 4-20mA, Modbus RS485, clamp on flow meter suppot remote monitoring in PLC control room.

Pipe Size:?DN15-DN40mm (1/2¡±~1 1/2¡±)
Flow Range:¡À0.1m/s ~¡À5m/s
Temperature: 0~75¡æ (standard)
Output: 4-20mA, OCT Pulse, RS485
Accuracy:?¡À1% of measured value
Power Supply: DC10-24V

This liquid flow meter for industrial is easy and accurate flow measurement without interrupting the process, Clamp-on type transducer easily mountable on existing pipes, non-invasive type.Suitable for most of applications. Measuring accuracy: +/-1.0% of FS Transducer temperature: -30~90¡ãC/-30¡ãC~160¡ãC Measuring clean liquids Built-in rechargeable battery 3.6V Communication: RS232

Ultrasonic Flow meter handheld clamp on flowmeter no pipe cutting required. The user simply clamp on the flow sensor to the pipe surface. Ultrasonic Flow meter handheld clamp on flowmeter can then detect the flow through ultrasonic waves, and then automatically calculate the flow rate value, flow accumulator, etc. No pipe cutting means no damage to the pipe. So as long as the pipes are in good condition, the installation on the flowmeter will not provide the possibility of leakage. Sensor: Clamp-on/External Principle: transmit time Size: DN15mm-DN6000mm Measuring medium: Liquid 3.6V Battery-powered

Modular type ultrasonic flow meter has high accuracy
Linearity: better than 0.5%, Repeatability: better than 0.2%, Accuracy is better than ¡À1%
It also have wide measuring range Several types transducer for selection, pipe size from DN15mm to DN6000mm
Liquid Types: Any single uniform liquid which can transmit ultrasonic
Security : Setup values Modification Lockout. Access code needs unlocking
Display: 4×16 character
Communication: RS-232 interface.75-57600bps, compatible with Fuji ultrasonic flowmeter and
Interface other UFM on enquiry.
Transducers: Model M1 for standard, other 4 models for optional
Transducer Cable: Standard 5m x2 or can be extended to 10m x2

Clamp on ultrasonic flow meter are widely used in tap water, heating, water conservancy, metallurgy, chemical industry, machinery, energy and other industries. Portable Hand Held Ultrasonic Flow Meter can be used for production monitoring, flow verification, temporary detection, flow inspection, water meter balance debugging, heat network balance debugging, and energy-saving monitoring. Measuring accuracy: +/-1.0% of FS Transducer temperature: -30~90¡ãC/-30¡ãC~160¡ãC Measuring clean liquids Battery-powered,for 12 hours Communication: RS232

Wastewater ultrasonic flow meter sensor for liquid are widely used in tap water, heating, water conservancy, metallurgy, chemical industry, machinery, energy and other industries. Wastewater ultrasonic flow meter sensor for liquid can be used for production monitoring, flow verification, temporary detection, flow inspection, water meter balance debugging, heat network balance debugging, and energy-saving monitoring. Measuring accuracy: +/-1.0% of FS Transducer temperature: -30~90¡ãC/-30¡ãC~160¡ãC Measuring clean liquids Battery-powered,for 12 hours Communication: RS232

QT621 is a portable transit-time ultrasonic flow meter with advanced functions. Portable ultrasonic flow meter includes matched precision transducers and signal processing circuitry to accurately measure the flow of most liquids. With 4-20mA and RS485 communication available, QT621 support quickly verify the flow reading of another meter and to data log flow system values over an extended time period.

Size: 1¡å~48¡å(25mm~1200mm)
Flow Range:¡À0.01 m/s~ ¡À12 m/s
Accuracy: ¡À1%
Repeatability: 0.2%
Output: 4-20mA, RS485
Power supply: Internal lithium 3000mAh
Transducer: IP68

Wall Mounted Ultrasonic Flowmeter 25mm water flow meter are used in conjunction with clamp on transducer to accurately measure liquid flow in closed pipes without the need to insert any mechanical parts into the pipe wall or into the fluid inside.
Using ultrasonic transit time technology, controlled by a microprocessor system, it holds a large amount of data, making it available for pipes of almost any material, from 15mm to 6000mm diameter (depending on the sensor model). This series can measure fluids at various temperatures (up to 160¡ãC).
Accuracy: +/-1.0% of FS
Wide range: DN15mm-DN6000mm
Measuring clean liquids
Power supply: 24VDC/85VAC-2265AC
Communication: RS485

QT621 battery powered ultrasonic clamp on flow meters are widely used from simple water flow
measurements to energy flow monitoring and automated process control.
Portable ultrasonic flow meters are with various kinds of output signals, including, 4-20mA analog and RS485 modbus which is very common and convenient for onsite monitoring.

Size: 1¡å~48¡å(25mm~1200mm)
Flow Range:¡À0.01 m/s~ ¡À12 m/s
Accuracy: ¡À1%
Repeatability: 0.2%
Output: 4-20mA, RS485
Power supply: Internal lithium 3000mAh
Transducer: IP68

Drinking water flowmeter ultrasonic clamp on type flowmeter is a portable liquid flow measurement device with a sensor. This Drinking water flowmeter ultrasonic clamp on type flowmeter proven transit-time ultrasonic measurement technology for superior accuracy and ease of installation and installation. This easy-to-use flowmeter comes in a rugged, waterproof carrying case for easy transport of the display, sensor, and cables between measurement locations. High accuracy +/-1.0% of FS Transducer temperature: -30~90¡ãC/-30¡ãC~160¡ãC Measuring clean liquids Battery-powered,for 12 hours Communication: RS232

According to market request,the power supply can 24VDC or 220VAC or solar powered;Current the solar powered ultrasonic flow meter is more popular,beacuse solar powered meets international requirements, energy saving and environmental protection.
2 way input
4-20mA,Pulse,OCT,RS485
Bi-directional flow measurement
Backlit LCD

Pipeline ultraosnic flow meter directly contact the liquid and make the measuring accuracy better than clamp on ultrasonic flowmeter.And installation easy,don’t need calculate the sensor installation distance and cover the coupling agent in the pipe,so this meter can collect the signal very well.
Accuracy:¡À1.0 %
Viscosity:0.1~¡À10m/s
Output:4~20mA,Pulse,OCT,RS485
Body material:Standard carbon steel,SS304 and SS316 are optional

The Q&T solar power ultrasonic water flow meter that is designed for open channel flow metering, whether you have a flume, weir or any other primary device. This meter has 4-20mA, RS485 and relay output, which is a good choice for different needs of channel flow monitoring.

Analogue?Output: 4-20mA,?corresponding?to?instantaneous?flow
Relays?Output: Standard?2?relay?outputs(Optional?up?to?6?relays)
Serial?Communication: RS485,?MODBUS?-RTU?standard?protocol
Ambient?Temperature: -40 ~70 Degree C
Measure?Cycle: 1?second?(selectable?2?seconds?)
Power?Supply: DC24V?(+5%)?0.2A;?AC220V?(+20%)?0.1A?;Optional?DC12V