Multi-channel flowmeter 0.5% accuracy ultrasonic flow meters

Digital wall Mounted Ultrasonic Water Liquid Flow Meter measure flow by propagating ultrasonic waves into a liquid-filled pipe. Digital wall Mounted Ultrasonic Water Liquid Flow Meter are located outside the pipeline and offer a wide range of pipeline sizes with no pressure loss, no contact with the liquid inside, and no moving parts. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm None cut down pipe Power supply: 24VDC/85VAC-2265AC Communication: RS485

With ultrasonic flow meters, the flow of liquids can be measured reliably – independent of conductivity, pressure, temperature, and in applications where traceability and guaranteed accuracy are required, the external ultrasonic sensor is the first choice. Clamp-on ultrasonic sensors, on the other hand, are mounted on the outer wall of the pipe and can therefore also be used for temporary measurements.
Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring clean liquids Built-in rechargeable battery 3.6V Communication: RS232

Fixed type ultrasonic clamp on flow meter adopts the self-development measurement technology.This measurement technique is a faster and more accurate process time measurement algorithm. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring single clean liquids Power supply: 24VDC/85VAC-2265AC Communication: RS485

Digital water ultrasonic flow meter is a portable liquid flow measurement device with a sensor. This 2-inch clamp-On Ultrasonic Flow Meterutilizes proven transit-time ultrasonic measurement technology for superior accuracy and ease of installation and installation. This easy-to-use flowmeter comes in a rugged, waterproof carrying case for easy transport of the display, sensor, and cables between measurement locations. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring single clean liquids Power supply: 24VDC/85VAC-2265AC Storage: SD card optional Heat meter optional

Protable Ultrasonic Water Flowmeter Price,Ultrasonic Flow Meter is a portable liquid flow measurement device with a sensor. Protable Ultrasonic Water Flowmeter Price,Ultrasonic Flow Meter adopt transit-time ultrasonic measurement technology for superior accuracy and ease of installation and installation. This easy-to-use flowmeter comes in a rugged, waterproof carrying case for easy transport of the display, sensor, and cables between measurement locations. High accuracy +/-1.0% of FS Transducer temperature: -30~90¡ãC/-30¡ãC~160¡ãC Measuring clean liquids Battery-powered,for 12 hours Communication: RS232

Highest Quality Handheld ultrasonic flow meter & Solutions, ultrsonic flow meter is a ideal for liquids such as chemical,visous liquids, and sea water. The non-intrusive, clamp-on ultrasonic flow meter fits pipes between 1/2″ to 48″ internal diameter. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Medium: clean liquids,pure water Built-in rechargeable battery 3.6V Measurment unit: Meter, Feet,Cubic Meter.

Low Price Wall Mounted Ultrasonic Water Flowmeter Clamp On Ultrasonic Flow Meter is a portable liquid flow measurement device with a sensor. Low Price Wall Mounted Ultrasonic Water Flowmeter Clamp On Ultrasonic Flow Meter proven transit-time ultrasonic measurement technology for superior accuracy and ease of installation and installation. This Low Price Wall Mounted Ultrasonic Water Flowmeter Clamp On Ultrasonic Flow Meter comes in a rugged, waterproof carrying case for easy transport of the display, sensor, and cables between measurement locations. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring single clean liquids Power supply: 24VDC/85VAC-2265AC Storage: SD card optional Heat meter optional

Q&T Wall mounted ultrasonic flowmeter clamp on type transducer is a high precision no-cut tube measurement method. This special design includes matching sensors for ease of use and is ideal for installation in existing systems Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring single clean liquids Power supply: 24VDC/85VAC-2265AC Storage: SD card optional Heat meter optional

Clamp on flow meter sensor portable ultrasonic flowmeter, no pipe cutting required. This is very different from traditional flow devices. The user simply clamp on the flow sensor to the pipe surface. ThePortable handheld ultrasonic flowmeter clamp on water flowmeter can then detect the flow through ultrasonic waves, and then automatically calculate the flow rate value, flow accumulator, etc. No pipe cutting means no damage to the pipe. So as long as the pipes are in good condition, the installation on the flowmeter will not provide the possibility of leakage. This advantage is more suitable for strong acid, strong alkali, poisoning, corrosive liquid, etc. Sensor: Clamp-on/External Principle: transmit time Size: DN15mm-DN6000mm Measuring medium: Liquid 3.6V Battery-powered

Clamp on ultrasonic flow meter are widely used in tap water, heating, water conservancy, metallurgy, chemical industry, machinery, energy and other industries. Portable Hand Held Ultrasonic Flow Meter can be used for production monitoring, flow verification, temporary detection, flow inspection, water meter balance debugging, heat network balance debugging, and energy-saving monitoring. Measuring accuracy: +/-1.0% of FS Transducer temperature: -30~90¡ãC/-30¡ãC~160¡ãC Measuring clean liquids Battery-powered,for 12 hours Communication: RS232

Pipeline ultraosnic flow meter directly contact the liquid and make the measuring accuracy better than clamp on ultrasonic flowmeter.And installation easy,don’t need calculate the sensor installation distance and cover the coupling agent in the pipe,so this meter can collect the signal very well.
Szie:DN15~DN6000
Accuracy:¡À1.0 %
Viscosity:0.1~10m/s
Measuring cycle:50mS

QT621 portable type ultrasonic flow meter is widely applied in oil industry, water treatment, pure water, chemical and etc.
Portable ultrasonic flow meter transmitter configurable for flow and thermal energy measurement. QT621 portable ultrasonic flow meter support quickly verify the flow reading of another meter and to data log flow system values over an extended time period.

Size: 1¡å~48¡å(25mm~1200mm)
Flow Range:¡À0.01 m/s~ ¡À12 m/s
Accuracy: ¡À1%
Repeatability: 0.2%
Output: 4-20mA, RS485
Power supply: Internal lithium 3000mAh
Transducer: IP68

Flange ultrasonic flow sensors are popular solution to simplify flow measurement across a variety of applications and sensors can be made from 50~2000mm,standard body material is carbon steel, SS304 and SS316 are optional.
Input:Two-wire PT1000
Output:4-20mA,Pulse,OCT
Communication:RS485
Szie:DN15~DN6000
Accuracy:¡À1.0 %

Digital portable ultrasonic flowmeters are widely used in tap water, heating, water conservancy, metallurgy, chemical industry, machinery, energy and other industries. It can be used for production monitoring, flow verification, temporary detection, flow inspection, water meter balance debugging, heat network balance debugging, and energy-saving monitoring. It is a tool instrument for timely flow detection. This ultrasonic flowmeter has a built-in data logger. The built-in data logger has a space of 24K bytes and can store 2000 lines of measurement data. The rechargeable power supply has a built-in high-capacity nickel-metal hydride rechargeable battery, which can support the flowmeter to work continuously for more than 12 hours. Measuring accuracy: +/-1.0% of FS Transducer temperature: -30~90¡ãC/-30¡ãC~160¡ãC Measuring clean liquids Battery-powered,for 12 hours Communication: RS232

This Open Channel Water Meters can be widely applied to the environmental protection, water treatment, irrigation, chemical, and other industries. Sewage and rainwater are often transported to the treatment plant in open collection channels or flumes. The flow rate is measured at various points in these channels, and our open channel flow meters are the good choice for these applications.

Specifications:
Display: Backlight?LCD
Flow?Rate?Range: 0.0000~99999L/S?or?m3/h
The?maximum?of Accumulative Flow: 9999999.9?m3/h
Accuracy?of?Change in Level: 1mm?or?0.2%?of?full?span?(whichever?is?greater)
Resolution: 1mm
Analogue?Output: 4-20mA,?corresponding?to?instantaneous?flow
Relays?Output: Standard?2?relay?outputs(Optional?up?to?6?relays)
Serial?Communication: RS485,?MODBUS?-RTU?standard?protocol

Sewage liquid ultrasonic flowmeter handheld ultrasonic water flow meter is a non-contact instrument, which can measure the flow of medium with large diameter and can also be used for the measurement of medium that is not easy to contact and observe. Its measurement accuracy is very high, and the external clip-type installation can reach the highest accuracy of ¡À1.0%. It is almost not disturbed by various parameters of the measured medium, especially it can solve the strong corrosiveness, non-conductivity, Flow measurement of radioactive and flammable and explosive media Measuring accuracy: +/-1.0% of FS Transducer temperature: -30~90¡ãC/-30¡ãC~160¡ãC Measuring clean liquids Battery-powered,for 12 hours Communication: RS232

PLCM series ultrasonic open channel flow meter is a low cost choice. It is a hot sell product for river channel measuring. The product supports weirs or notches of different standards in various countries and can be widely used for measurement or monitoring of total water drainage.
Display: Backlight LCD
The maximum of Accumulative Flow: 9999999.9 m3/h
Accuracy of Change in Level: 1mm or 0.2% of full span (whichever is greater)
Resolution: 1mm
Analogue Output: 4-20mA, corresponding to instantaneous flow
Relays Output: Standard 2 relay outputs(Optional up to 6 relays)
Serial Communication: RS485, MODBUS -RTU standard protocol
Ambient Temperature: -40 ~70 Degree C
Power Supply: DC24V (+5%) 0.2A; AC220V (+20%) 0.1A ;Optional DC12V

Digital Ultrasonic Flow Meter Rotameter Stainless Steel DN15 portable ultrasonic flow meter is an ultrasonic flowmeter used to measure the flow rate of liquids in closed pipes. The transducer is clamp-on type, which will provide the benefits of contamination-free operation and ease of installation. The transit time flowmeter includes two transducers, which act as ultrasonic transmitters and receivers. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring clean liquids Power supply: 24VDC/85VAC-2265AC Communication: RS485

PLCM open channel flow meter is LCD display, it is a good choice for waster water, rive, channel flow measuring, We can do high quality OEM for you.
Display: Backlight LCD
The maximum of Accumulative Flow: 9999999.9 m3/h
Accuracy of Change in Level: 1mm or 0.2% of full span (whichever is greater)
Resolution: 1mm
Analogue Output: 4-20mA, corresponding to instantaneous flow
Relays Output: Standard 2 relay outputs(Optional up to 6 relays)
Serial Communication: RS485, MODBUS -RTU standard protocol
Ambient Temperature: -40 ~70 Degree C
Power Supply: DC24V (+5%) 0.2A; AC220V (+20%) 0.1A ;Optional DC12V

Q&T Modbus Digital Ultrasonic Fluid Flow Meter Clamp On Ultrasonic Flowmeter provide you with an accurate, easy-to-install flow meter. wall mount flow sensor feature quick, easy clamp-on sensor installation, configuration, and a user-programmable menu-driven interface for easy commissioning in the field. Q&T Modbus Digital Ultrasonic Fluid Flow Meter Clamp On Ultrasonic Flowmeter use a special technology to ensure highly accurate flow measurement. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring single clean liquids Power supply: 24VDC/85VAC-2265AC Storage: SD card optional Heat meter optional

OEM ultrasonic Flow meter for applications in clean water and in low conductivity media. Operating principle based on transit time measurement.
Inline type ultrasonic flow meter can be OEM,such as Body color,Transmitter color,Channle number,Logo display etc.
Power supply:DC24VDC or AC220V
Output:4-20mA,OCT,Pulse
Comm port:RS485 MODBUS-RTU

Wall mounted ultrasonic flow meter water flowmeter with 4-20mA RS485 communication is simple to install and is suitable for large diameter pipes requiring monitoring and flow measurement, as well as a wide network of smaller supply lines.Wall mounted ultrasonic flow meter water flowmeter with 4-20mA RS485 communication provide the tools needed to meet the diverse requirements of such a demanding industry. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring clean liquids Power supply: 24VDC/85VAC-2265AC Communication: RS485

This ultrasonic water flow meter can directly display the instant and accumulative flow. This open channel ultrasonic flow meter is based on the flow rate-water level calculation method, and adopts an advanced flow rate measuring instrument and water level measuring instrument to ensure a new intelligent flow system.

Specifications:
Sensor?Level?Range: 0-4.0m; other?level?range?also?available
Blind?zone: 0.20m
Temperature?Compensation: Integral?in?probe
Pressure?Rating: 0.2MPa
Beam?Angle: 8*?(3db)
Cable?Length: 10m?standard?(can?be?extended?to?1000m)
Sensor?Material: ABS,?PVC?or?PTFE?(optional)
Sensor?Protection Class: IP68
Output: 4-20mA, Relays, RS485

Strap on ultrasonic flow meter enjoy ±1.0% accuracy in real application,300times/second high responsive speed,Q&T water liquid ultrasonic flow meter could measure 0.03m/s low flow velocity. Accuracy:±1% of measured value;
Temperature:Transmitter: -14℉~140℉(-20℃~60℃),Transducer: -40℉~176℉(-40℃~80℃,standard); Humidity:Up to 99% RH, non-condensing;
Transmitter material:PC/ABS,IP65;
Transducer:ABS,IP68

This open channel flow meter uses ultrasonic principle to measure the water level height in the open channel weir, and then the microprocessor calculates the corresponding flow value automatically. The level value is converted to a particular flow in a particular weirs/flumes, so accurate level values are important. It is a sensor designed for open channel flow to provide accurate level readings.
Power Supply: DC24V (+5%) 0.2A; AC220V (+20%) 0.1A ;Optional DC12V
Flow Rate Range: 0.0000~99999L/S or m3/h
Analogue Output: 4-20mA, corresponding to instantaneous flow
Relays Output: Standard 2 relay outputs(Optional up to 6 relays)
Serial Communication: RS485, MODBUS -RTU standard protocol
Ambient Temperature: -40 ~70 Degree C

QT621 portable type ultrasonic clamp on flow meters use clamp-on transducers that are mounted externally on the surface of the pipe and which generate pulses that pass through the pipe wall.
Portable ultrasonic flow meters can be easily moved and installed in different pipes and convenient to carry site to site, which is very convenient for users to monitor the data.

Size: 1¡å~48¡å(25mm~1200mm)
Flow Range:¡À0.01 m/s~ ¡À12 m/s
Accuracy: ¡À1%
Repeatability: 0.2%
Output: 4-20mA, RS485
Power supply: Internal lithium 3000mAh
Transducer: IP68

Q&T wall-mounted type ultrasonic flowmeter measure flow rate by propagating ultrasound waves into liquid-filled pipes and measuring the flow. With transit time, these clamp-on ultrasonic meters are outside the pipe, providing a wide range of pipe sizes, no pressure loss, none contact with internal liquid and no moving parts.
Accuracy: +/-1.0% of FS
Wide range: DN15mm-DN6000mm
None cut down pipe
Power supply: 24VDC/85VAC-2265AC
Communication: RS485

QT621 Portable ultrasonic flow meter a type of portable instrument for non-invasive, quick flow and energy measurement.Portable ultrasonic flow meter matched precision transducers and signal processing circuitry to accurately measure the flow of most liquids. QT621 ultrasonic flow meter support quickly verify the flow reading of another meter and to data log flow system values over an extended time period.

Size: 1¡å~48¡å(25mm~1200mm)
Flow Range:¡À0.01 m/s~ ¡À12 m/s
Accuracy: ¡À1%
Repeatability: 0.2%
Output: 4-20mA, RS485
Power supply: Internal lithium 3000mAh
Transducer: IP68

Q&T PLCM Open Channel flow meter is Wall mounted converter ultrasonic flow meter for sewage water Open Channel Flow Meter, The cable length between probe and host up to 1000m; This PLCM ultrasonic flow meters are perfect for wastewater applications.
The probe with leak-proof structure and IP68 protect grade.
Display: Backlight LCD
The maximum of Accumulative Flow: 9999999.9 m3/h
Accuracy of Change in Level: 1mm or 0.2% of full span (whichever is greater)
Resolution: 1mm
Analogue Output: 4-20mA, corresponding to instantaneous flow
Relays Output: Standard 2 relay outputs(Optional up to 6 relays)
Serial Communication: RS485, MODBUS -RTU standard protocol
Ambient Temperature: -40 ~70 Degree C
Power Supply: DC24V (+5%) 0.2A; AC220V (+20%) 0.1A ;Optional DC12V

Wall Mounted ultrasonic water flow meter Clamp on transducer adopts the self-development measurement technology.This measurement technique is a faster and more accurate process time measurement. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring single clean liquids Power supply: 24VDC/85VAC-2265AC Communication: RS485