modbus ultrasonic flow meter with data logger

Q&T brand ultrasonic flow meter is real flow calibrated,5 flow velocity point and calibrate 3 times for each flow velocity point.Q&T calibration device can calibrate from DN3~DN3000mm,and adopt Seimens,Rosemount,E+H brand flow meter as the standard meter.
Single channel ultrasonic flow meter accuracy <1.0% Multi-channel ultrasonic flow meter caccuracy can reach 0.5%

PLCM open channel flow meter is LCD display, it is a good choice for waster water, rive, channel flow measuring, We can do high quality OEM for you.
Display: Backlight LCD
The maximum of Accumulative Flow: 9999999.9 m3/h
Accuracy of Change in Level: 1mm or 0.2% of full span (whichever is greater)
Resolution: 1mm
Analogue Output: 4-20mA, corresponding to instantaneous flow
Relays Output: Standard 2 relay outputs(Optional up to 6 relays)
Serial Communication: RS485, MODBUS -RTU standard protocol
Ambient Temperature: -40 ~70 Degree C
Power Supply: DC24V (+5%) 0.2A; AC220V (+20%) 0.1A ;Optional DC12V

QT621 battery powered ultrasonic clamp on flow meters are widely used from simple water flow
measurements to energy flow monitoring and automated process control.
Portable ultrasonic flow meters are with various kinds of output signals, including, 4-20mA analog and RS485 modbus which is very common and convenient for onsite monitoring.

Size: 1¡å~48¡å(25mm~1200mm)
Flow Range:¡À0.01 m/s~ ¡À12 m/s
Accuracy: ¡À1%
Repeatability: 0.2%
Output: 4-20mA, RS485
Power supply: Internal lithium 3000mAh
Transducer: IP68

HVAC Ultrasonic Flow Meters is a non-contact instrument, which can measure the flow of medium with large diameter and can also be used for the measurement of medium that is not easy to contact and observe. Its measurement accuracy is very high, and the external clip-type installation can reach the highest accuracy of ¡À1.0%. It is almost not disturbed by various parameters of the measured medium, especially it can solve the strong corrosiveness, non-conductivity, Flow measurement of radioactive and flammable and explosive media
Measuring accuracy: +/-1.0% of FS
Transducer temperature: -30~90¡ãC/-30¡ãC~160¡ãC
Measuring clean liquids Battery-powered,for 12 hours
Communication: RS232

QTDS-100H handheld liquid ultrasonic flow meter China supplier is a portable liquid flow measurement device with a sensor. QTDS-100H handheld liquid ultrasonic flow meter China supplier proven transit-time ultrasonic measurement technology for superior accuracy and ease of installation and installation. This easy-to-use flowmeter comes in a rugged, waterproof carrying case for easy transport of the display, sensor, and cables between measurement locations. High accuracy +/-1.0% of FS Transducer temperature: -30~90¡ãC/-30¡ãC~160¡ãC Measuring clean liquids Battery-powered,for 12 hours Communication: RS232

Handheld ultrasonic flow meter with clamp on Middle transducer is easy and accurate flow measurement without interrupting the process, Clamp-on type transducer easily mountable on existing pipes, non-invasive type.Suitable for most of applications. Measuring accuracy: +/-1.0% of FS Transducer temperature: -30~90¡ãC/-30¡ãC~160¡ãC Measuring clean liquids Built-in rechargeable battery 3.6V Communication: RS232

Pipeline ultraosnic flow meter directly contact the liquid and make the measuring accuracy better than clamp on ultrasonic flowmeter.And installation easy,don’t need calculate the sensor installation distance and cover the coupling agent in the pipe,so this meter can collect the signal very well.

Fixed type clamp on ultrasonic flowmeter with RS485 Modbus flow meter is an ultrasonic flowmeter used to measure the flow rate of liquids in closed pipes. The transducer is a non-contact, clamp-on type, which will provide the benefits of contamination-free operation and ease of installation. The transit time flowmeter employs two transducers, which act as ultrasonic transmitters and receivers. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring clean liquids Power supply: 24VDC/85VAC-2265AC Communication: RS485

Flange ultrasonic flow meter is one kind of contact flow metera and it is time difference meters that use ultrasonic technology to measure the velocity of an acoustically conductive liquid moving through it.
Q&T brand ultrasonic flow meter is one kind of economy type flow meter for liquid,multi channle inline ultrasonic flow meter can reach 0.5% accuracy.

Modular type ultrasonic flow meter is designed to measure the fluid ve-locity of liquid within a closed conduit. The transducers are a non-contacting, clamp-on type, which will provide benefits of non-fouling operation and easy installation.Transit-time flow meter utilizes two transducers that function as both ultrasonic transmitters and receivers.
Pipe SizeDN 15mm~6000mm
Flow ve-locity range0-¡À30m/s
AccuracyBetter than ¡À1%
Power Supply: AC220V
Power Consumption: Less than 1.5W

Wall mounted ultrasonic flow meter clamp on type flowmeter is a high precision no-cut tube measurement method. This special design includes matching sensors for ease of use and is ideal for installation in existing systems Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring single clean liquids Power supply: 24VDC/85VAC-2265AC Storage: SD card optional Heat meter optional

Q&T ultrasonic water flow meter maily be used to measure water and measure repeatability can reach 0.2%.
Clamp on water flow meter which used the transfer time technology,when install the transducer,workers will choose different install method for different size pipe,such as V method,Z method,W method.
Output:4-20mA,RS485
Power supply:24VDC,90~245VAC power is optional
Accuracy:±1.0%
Repeatability:±0.2%

An ultrasonic flow meter utilizes ultrasound to measure the velocity of a fluid and is used in a variety of fluid applications
Pipeline ultraosnic flow meter directly contact the liquid and make the measuring accuracy better than clamp on ultrasonic flowmeter.And installation easy,don’t need calculate the sensor installation distance and cover the coupling agent in the pipe,so this meter can collect the signal very well.

Digital wall Mounted Ultrasonic Water Liquid Flow Meter measure flow by propagating ultrasonic waves into a liquid-filled pipe. Digital wall Mounted Ultrasonic Water Liquid Flow Meter are located outside the pipeline and offer a wide range of pipeline sizes with no pressure loss, no contact with the liquid inside, and no moving parts. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm None cut down pipe Power supply: 24VDC/85VAC-2265AC Communication: RS485

QT811 ultrasonic flow meter is specially designed for small pipe sizes clamp on flow measurements. It is integrated design with the monitor LCD and the sensors in one body, user could read flow rate directly from the device. With various kinds of outputs including 4-20mA, OCT pulse and RS485 modbus, ultrasonic flow meter could achieve remote monitoring in central control room.

Pipe Size:?DN15-DN40mm (1/2¡±~1 1/2¡±)
Flow Range:¡À0.1m/s ~¡À5m/s
Temperature: 0~75¡æ (standard)
Output: 4-20mA, OCT Pulse, RS485
Accuracy:?¡À1% of measured value
Power Supply: DC10-24V

Clamp on flow meter sensor portable ultrasonic flowmeter, no pipe cutting required. This is very different from traditional flow devices. The user simply clamp on the flow sensor to the pipe surface. ThePortable handheld ultrasonic flowmeter clamp on water flowmeter can then detect the flow through ultrasonic waves, and then automatically calculate the flow rate value, flow accumulator, etc. No pipe cutting means no damage to the pipe. So as long as the pipes are in good condition, the installation on the flowmeter will not provide the possibility of leakage. This advantage is more suitable for strong acid, strong alkali, poisoning, corrosive liquid, etc. Sensor: Clamp-on/External Principle: transmit time Size: DN15mm-DN6000mm Measuring medium: Liquid 3.6V Battery-powered

Ultrasonic energy BTU meter is one kind of BTU meter which mainly liquid heat and cold.
Ultrasonic flow meter connect one pair of PT1000 temperature will become BTU meter
Pipe size:25~1200mm
Accuracy:±1.0%
Output:4-20mA,RS485
Transducer temperature:-40~80℃
Transducer protect:IP68
Power supply:24VDC

Professional Cheap Ultrasonic Flowmeter Hydraulic Oil Flow Meter Clamp On Ultrasonic Flow Meter consists of two parts: a transmitter unit and a transducer. Magnetic external clamps on the sensor are easy to install and connect to metal tubing for continuous flow measurement. It is especially suitable for on-site flow measurement of various pressure requirements. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring clean liquids Power supply: 24VDC/85VAC-2265AC Communication: RS485

China factory RS485 module clamp on ultrasonic flow meter is an ultrasonic flowmeter used to measure the flow rate of liquids in closed pipes. The transducer is a non-contact, clamp-on type, which will provide the benefits of contamination-free operation and ease of installation. The transit time flowmeter employs two transducers, which act as ultrasonic transmitters and receivers. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring clean liquids Power supply: 24VDC/85VAC-2265AC Communication: RS485

Wall Mounted ultrasonic flowmeter proven transit-time ultrasonic measurement technology This technology can be used for permanent installations where intrusive flow meters are not economically viable for permanent installations on large pipelines and for all the different process fluids encountered in the network. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring clean liquids Power supply: 24VDC/85VAC-2265AC Communication: RS485

QT621 handheld ultrasonic flow meter support accurate bidirectional and highly dynamic flow measurement
with the non-invasive clamp-on technology. Handheld type ultrasonic flow meter mainly applies for measuring the flow of homogeneous medium fluid in the water injection flow measurement, raw water flow measurement, tap water flow measurement etc.

Size: 1¡å~48¡å(25mm~1200mm)
Flow Range:¡À0.01 m/s~ ¡À12 m/s
Accuracy: ¡À1%
Repeatability: 0.2%
Output: 4-20mA, RS485
Power supply: Internal lithium 3000mAh
Transducer: IP68

Wall Mounted Ultrasonic flow sensor Water Clamp on flow meter consists of two parts: a transmitter unit and a transducer. Magnetic external clamps on the sensor are easy to install and connect to metal tubing for continuous flow measurement. It is especially suitable for on-site flow measurement of various pressure requirements. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring clean liquids Power supply: 24VDC/85VAC-2265AC Communication: RS485

Water Ultrasonic Flow Meter Digital Clamp on transducer water flowmeter no pipe cutting required. The user simply clamp on the flow sensor to the pipe surface. Water Ultrasonic Flow Meter Digital Clamp on transducer water flowmeter can then detect the flow through ultrasonic waves, and then automatically calculate the flow rate value, flow accumulator, etc. No pipe cutting means no damage to the pipe. So as long as the pipes are in good condition, the installation on the flowmeter will not provide the possibility of leakage. Sensor: Clamp-on/External Principle: transmit time Size: DN15mm-DN6000mm Measuring medium: Liquid 3.6V Battery-powered

The ultrasonic open channel flowmeter can be equipped with a communication interface, which is easy to connect with SCADA systems to achieve industrial remote monitoring and control. This Open Channel flow meter measures level, flow rate and total volume of water flowing through weirs, flumes, and channels etc.

Specifications:
Sensor?Level?Range: 0-4.0m; other?level?range?also?available
Blind?zone: 0.20m
Temperature?Compensation: Integral?in?probe
Pressure?Rating: 0.2MPa
Beam?Angle: 8*?(3db)
Cable?Length: 10m?standard?(can?be?extended?to?1000m)
Sensor?Material: ABS,?PVC?or?PTFE?(optional)
Sensor?Protection Class: IP68

Portable handheld ultrasonic flowmeter clamp on water flowmeter installation, no pipe cutting required. This is very different from traditional flow devices. The user simply clamp on the flow sensor to the pipe surface. ThePortable handheld ultrasonic flowmeter clamp on water flowmeter can then detect the flow through ultrasonic waves, and then automatically calculate the flow rate value, flow accumulator, etc. No pipe cutting means no damage to the pipe. So as long as the pipes are in good condition, the installation on the flowmeter will not provide the possibility of leakage. This advantage is more suitable for strong acid, strong alkali, poisoning, corrosive liquid, etc. Sensor: Clamp-on/External Principle: transmit time Size: DN15mm-DN6000mm Measuring medium: Liquid 3.6V Battery-powered

This ultrasonic water flow meter can directly display the instant and accumulative flow. This open channel ultrasonic flow meter is based on the flow rate-water level calculation method, and adopts an advanced flow rate measuring instrument and water level measuring instrument to ensure a new intelligent flow system.

Specifications:
Sensor?Level?Range: 0-4.0m; other?level?range?also?available
Blind?zone: 0.20m
Temperature?Compensation: Integral?in?probe
Pressure?Rating: 0.2MPa
Beam?Angle: 8*?(3db)
Cable?Length: 10m?standard?(can?be?extended?to?1000m)
Sensor?Material: ABS,?PVC?or?PTFE?(optional)
Sensor?Protection Class: IP68
Output: 4-20mA, Relays, RS485

Modular type ultrasonic flow meter is one type of ultrasonic flow meter.It has very small size and easy to be installed into instrument box. This type flow is working with clamp type transducer normally. The max measure tube is DN3000 pipe. It have 4-02mA, pulse, and RS485 output also.It even could link with temperature sensor and work as ultrasonic BTU meter.
Accuracy: ±1%
Velocity: 0.5s
Display: LCD with backlight 2*20leters
Signal Outputs: 4-20mA or o-20mA,RS485,Pulse
Liquid Types: Virtually all commonly used liquids
Pipe Size: DN15-DN3000

Wall mounted clamp on ultrasonic flow meter water flowmeter is simple to install and is suitable for large diameter pipes requiring monitoring and flow measurement, as well as a wide network of smaller supply lines. Wall mounted clamp on ultrasonic flow meter water flowmeter provide the tools needed to meet the diverse requirements of such a demanding industry. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring clean liquids Power supply: 24VDC/85VAC-2265AC Communication: RS485

Clamp on ultrasonic flow meter equipment installation, no pipe cutting required. This is very different from traditional flow devices. The user simply clamp on the flow sensor to the pipe surface. The ultrasonic flowmeter can then detect the flow through ultrasonic waves, and then automatically calculate the flow rate value, flow accumulator, etc. No pipe cutting means no damage to the pipe. So as long as the pipes are in good condition, the installation on the flowmeter will not provide the possibility of leakage. This advantage is more suitable for strong acid, strong alkali, poisoning, corrosive liquid, etc. Sensor: Clamp-on/External Principle: transmit time Size: DN15mm-DN6000mm Measuring medium: Liquid 3.6V Battery-powered

This open channel flow meter consists of two elements, a host, which has display and an integral keypad for programming, and a transducer, which must be mounted directly above the surface to be measured. It can be widely applied to the environmental protection, water treatment, irrigation, chemical, and other industries.

Specifications:
Display: Backlight?LCD
Flow?Rate?Range: 0.0000~99999L/S?or?m3/h
The?maximum?of Accumulative Flow: 9999999.9?m3/h
Accuracy?of?Change in Level: 1mm?or?0.2%?of?full?span?(whichever?is?greater)
Resolution: 1mm
Analogue?Output: 4-20mA,?corresponding?to?instantaneous?flow
Relays?Output: Standard?2?relay?outputs(Optional?up?to?6?relays)
Serial?Communication: RS485,?MODBUS?-RTU?standard?protocol