Low Cost Handheld Flow Meter Inline Pipe Type Stationary Outdoor Ultrasonic Flow Meters

Liquid portable ultrasonic flowmeter clamp on type 3.6V battery powered can be easily installed, removed and transported. This flowmeter makes them ideal for industrial applications that are already operational or only require occasional flow measurement. In the latter case, the user can use the same clamp on flowmeter to measure flow in multiple locations by unloading and transporting the device for each measurement Measuring accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring clean liquids Built-in rechargeable battery 3.6V Communication: RS232

Ultrasonic Flow meter for applications in clean water and in low conductivity media. Operating principle based on transit time measurement.
High Isolation voltage,Strong anti-interference,Suppress voltage noise,Good isolation performance
Inline ultrasonic flow meter collect temperature signal and accuracy reach 0.001¡æ
When using inline ultrasonic flow meter to measure,allowing pipe with liner
Szie:DN15~DN6000
Accuracy:¡À1.0 %
Viscosity:0.1~¡À10m/s
Output:4~20mA,Pulse,OCT,RS485
Power supply:DC24V and AC220V
Connection way:Flange type

Clamp on flow meter sensor portable ultrasonic flowmeter, no pipe cutting required. This is very different from traditional flow devices. The user simply clamp on the flow sensor to the pipe surface. ThePortable handheld ultrasonic flowmeter clamp on water flowmeter can then detect the flow through ultrasonic waves, and then automatically calculate the flow rate value, flow accumulator, etc. No pipe cutting means no damage to the pipe. So as long as the pipes are in good condition, the installation on the flowmeter will not provide the possibility of leakage. This advantage is more suitable for strong acid, strong alkali, poisoning, corrosive liquid, etc. Sensor: Clamp-on/External Principle: transmit time Size: DN15mm-DN6000mm Measuring medium: Liquid 3.6V Battery-powered

Digital Wall Mounted Clamp on Ultrasonic Flowmeter Flow Meter is simple to install and is suitable for large diameter pipes requiring monitoring and flow measurement, as well as a wide network of smaller supply linesDigital Wall Mounted Clamp on Ultrasonic Flowmeter Flow Meter provide the tools needed to meet the diverse requirements of such a demanding industry. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring clean liquids Power supply: 24VDC/85VAC-2265AC Communication: RS485

Highest Quality Handheld ultrasonic flow meter & Solutions, ultrsonic flow meter is a ideal for liquids such as chemical,visous liquids, and sea water. The non-intrusive, clamp-on ultrasonic flow meter fits pipes between 1/2″ to 48″ internal diameter. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Medium: clean liquids,pure water Built-in rechargeable battery 3.6V Measurment unit: Meter, Feet,Cubic Meter.

This Waste Water open Channel flow meter has wide application, good for applications such as groundwater system flow
monitoring, industrial sewage discharge monitoring, flow into water treatment plants, effluent from water resource recovery, and
agriculture irrigation channels.

Specifications:
Display: Backlight?LCD
Flow?Rate?Range: 0.0000~99999L/S?or?m3/h
The?maximum?of Accumulative Flow: 9999999.9?m3/h
Accuracy?of?Change in Level: 1mm?or?0.2%?of?full?span?(whichever?is?greater)
Resolution: 1mm
Analogue?Output: 4-20mA,?corresponding?to?instantaneous?flow
Relays?Output: Standard?2?relay?outputs(Optional?up?to?6?relays)
Serial?Communication: RS485,?MODBUS?-RTU?standard?protocol

Not affected by water quality, the solar power ultrasonic open channel flowmeter can be equipped with a communication interface, which is easy to connect with SCADA systems to achieve industrial remote monitoring and control. This Open Channel flow meter measures level, flow rate and total volume of water flowing through weirs, flumes, and channels etc.

Specifications:
Sensor?Level?Range: 0-4.0m; other?level?range?also?available
Blind?zone: 0.20m
Temperature?Compensation: Integral?in?probe
Pressure?Rating: 0.2MPa
Beam?Angle: 8*?(3db)
Cable?Length: 10m?standard?(can?be?extended?to?1000m)
Sensor?Material: ABS,?PVC?or?PTFE?(optional)
Sensor?Protection Class: IP68

Industrial ultrasonic flow meter output for water ultrasonic flow meter pvc pipe heat meter is a ideal for liquids such as chemical,visous liquids, and sea water. The non-intrusive, clamp-on ultrasonic flow meter fits pipes between 1/2″ to 48″ internal diameter. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Medium: clean liquids,pure water Built-in rechargeable battery 3.6V Measurment unit: Meter, Feet,Cubic Meter.

The Q&T ultrasonic water flow meter that is designed for open channel flow metering, whether you have a flume, weir or any other primary device. This meter has 4-20mA, RS485 and relay output, which is a good choice for different needs of channel flow monitoring.

Analogue?Output: 4-20mA,?corresponding?to?instantaneous?flow
Relays?Output: Standard?2?relay?outputs(Optional?up?to?6?relays)
Serial?Communication: RS485,?MODBUS?-RTU?standard?protocol
Ambient?Temperature: -40 ~70 Degree C
Measure?Cycle: 1?second?(selectable?2?seconds?)
Power?Supply: DC24V?(+5%)?0.2A;?AC220V?(+20%)?0.1A?;Optional?DC12V

QT621 ultrasonic flow meter is a portable type flow meter for non-invasive, quick flow and energy measurement with clamp-on technology for many types of piping.
Portable type ultrasonic flow metere can be easily moved and installed in different pipes and convenient to carry site to site.

Size: 1¡å~48¡å(25mm~1200mm)
Flow Range:¡À0.01 m/s~ ¡À12 m/s
Accuracy: ¡À1%
Repeatability: 0.2%
Output: 4-20mA, RS485
Power supply: Internal lithium 3000mAh
Transducer: IP68

Handheld Ultrasonic Flowmeter Clamp on Flow Meter Portable Liquid Flow Meter with small transducer to measure flow rate through the pipe wall, the transit time ultrasonic flow principle. It is a 3.6V battery powered ultrsonic flow meter, for using on a wide range of sizes and can provide 24 hours measurement continuely. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring clean liquids Built-in rechargeable battery 3.6V 2000 lines storage Communication: RS232

QT621 handheld ultrasonic flow meter support to carry from site to site conveniently. Support accurate bidirectional and highly dynamic flow measurement with the non-invasive clamp-on technology. Portable ultrasonic flow meter mainly applies for measuring the flow of homogeneous medium fluid in the water injection flow measurement, raw water flow measurement, tap water flow measurement etc.

Size: 1¡å~48¡å(25mm~1200mm)
Flow Range:¡À0.01 m/s~ ¡À12 m/s
Accuracy: ¡À1%
Repeatability: 0.2%
Output: 4-20mA, RS485
Power supply: Internal lithium 3000mAh
Transducer: IP68

Ultrasonic Flow meter for applications in clean water and in low conductivity media. Operating principle based on transit time measurement.
Pipe material:Steel,Stainless steel,Cast iron,PVC,Cement pipe and allow pipe with lining
High Isolation voltage,Strong anti-interference,Suppress voltage noise,Good isolation performance
Inline ultrasonic flow meter collect temperature signal and accuracy reach 0.001¡æ

Non Contact Digital LCD Display Modular Type Ultrasonic Flow Meter Modular type ultrasonic flow meter is one type of transmit-time ultrasonic flow meter. Customer don’t need cut off pipe. The ultrasonic flow sensor could be clamped on pipe and measure the flow rate directly. It have digital LCD display. And the menu could be operated by button. This type flow meter could be used on DN15-DN6000 pipe. And it could work on most of pipes except cement pipe.
Principle: Transit- time ultrasonic flow meter
Accuracy: ¡À1%
Operation: 4 keys operation
Signal output:
1 way 4~20mA output, electric resistance 0~1K, accuracy0. 1%
1 way OCT pulse output (Pulse width 6~1000ms, default 200ms)
1 way relay output
Signal input:
3 way 4~20mA input,signal could be temperature, pressure or liquid level

QT811 clamp on BTU energy flow meter are popular in water treatment, pure water, chemical and etc. Clamp on type flow meter specially designed for small sizes DN15-DN40mm. As a type of small instrument, QT811 clamp on flow meter support quick flow and energy measurement for many types of pipings.

Pipe Size:?DN15-DN40mm (1/2¡±~1 1/2¡±)
Flow Range:¡À0.1m/s ~¡À5m/s
Temperature: 0~75¡æ (standard)
Output: 4-20mA, OCT Pulse, RS485
Accuracy:?¡À1% of measured value
Power Supply: DC10-24V

Ultrasonic Open Channel Flow Meter for Water is used with weir tank to measure the water flow rate in the open-channel. This meter is mainly used to measure sewage plants, sewage outfall of enterprises and institutions, city sewer flows and irrigation channels.
Ambient Temperature: -40 ~70 Degree C
Measure Cycle: 1 second (selectable 2 seconds )
Power Supply: DC24V (+5%) 0.2A; AC220V (+20%) 0.1A ;Optional DC12V
Multiple Output: 4-20 mA, relay and RS485 etc; easily connect up to most systems.

QT811 DN15-40mm clamp on flow meter is a new designed external clamp on measurement flow meter. Clamp on ultrasonic flow meter adopt non-invasive flow measurements, This involves sending and receiving ultrasonic pulses from a pair of sensors and examining the time difference in the signal. Clamp on flow meter support monitor the flow rate reading directly on the device.

Pipe Size:?DN15-DN40mm (1/2¡±~1 1/2¡±)
Flow Range:¡À0.1m/s ~¡À5m/s
Temperature: 0~75¡æ (standard)
Output: 4-20mA, OCT Pulse, RS485
Accuracy:?¡À1% of measured value
Power Supply: DC10-24V

Water Ultrasonic Flow Meter Digital Clamp on transducer water flowmeter no pipe cutting required. The user simply clamp on the flow sensor to the pipe surface. Water Ultrasonic Flow Meter Digital Clamp on transducer water flowmeter can then detect the flow through ultrasonic waves, and then automatically calculate the flow rate value, flow accumulator, etc. No pipe cutting means no damage to the pipe. So as long as the pipes are in good condition, the installation on the flowmeter will not provide the possibility of leakage. Sensor: Clamp-on/External Principle: transmit time Size: DN15mm-DN6000mm Measuring medium: Liquid 3.6V Battery-powered

This Open channel flow meter require accurate measurement of the surface level of a liquid. A flume, channel or structure which has a known characteristic flow per measured head, together with the measured liquid level, accurately define the flow rate through the system.

Analogue?Output: 4-20mA,?corresponding?to?instantaneous?flow
Relays?Output: Standard?2?relay?outputs(Optional?up?to?6?relays)
Serial?Communication: RS485,?MODBUS?-RTU?standard?protocol
Ambient?Temperature: -40 ~70 Degree C
Measure?Cycle: 1?second?(selectable?2?seconds?)
Power?Supply: DC24V?(+5%)?0.2A;?AC220V?(+20%)?0.1A?;Optional?DC12V

Portable Hand Held Ultrasonic Flow Meter are widely used in tap water, heating, water conservancy, metallurgy, chemical industry, machinery, energy and other industries. Portable Hand Held Ultrasonic Flow Meter can be used for production monitoring, flow verification, temporary detection, flow inspection, water meter balance debugging, heat network balance debugging, and energy-saving monitoring. Measuring accuracy: +/-1.0% of FS Transducer temperature: -30~90¡ãC/-30¡ãC~160¡ãC Measuring clean liquids Battery-powered,for 12 hours Communication: RS232

Ultrasonic flowmeter handheld ultrasonic flowsensor is a non-contact instrument, which can measure the flow of medium with large diameter and can also be used for the measurement of medium that is not easy to contact and observe. Ultrasonic flowmeter handheld ultrasonic flowsensor measurement accuracy is very high, and it is hardly disturbed by various parameters of the measured medium. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Medium: clean liquids,pure water Built-in rechargeable battery 3.6V Housing Material: ABS

Clamp on type sensor ultrasonic water flow meter no pipe cutting required. The user simply clamp on the flow sensor to the pipe surface. Clamp on type sensor ultrasonic water flow meter can then detect the flow through ultrasonic waves, and then automatically calculate the flow rate value, flow accumulator, etc. No pipe cutting means no damage to the pipe. So as long as the pipes are in good condition, the installation on the flowmeter will not provide the possibility of leakage. Sensor: Clamp-on/External Principle: transmit time Size: DN15mm-DN6000mm Measuring medium: Liquid 3.6V Battery-powered

QT811 clamp on flow meters are suitable for various liquids and compatible with various pipeline materials and sizes. Clamp on flow meter is a type of small size instrument for non-invasive, quick flow and energy measurement with clamp-on technology for many types of piping. With support for 4-20mA, Modbus RS485, clamp on flow meter suppot remote monitoring in PLC control room.

Pipe Size:?DN15-DN40mm (1/2¡±~1 1/2¡±)
Flow Range:¡À0.1m/s ~¡À5m/s
Temperature: 0~75¡æ (standard)
Output: 4-20mA, OCT Pulse, RS485
Accuracy:?¡À1% of measured value
Power Supply: DC10-24V

QT621 portable type ultrasonic clamp on flow meters support quite quick verify the flow reading of another meter and to data log flow system values over an extended time period.
Portable ultrasonic flow meter uses clamp-on transducers that are mounted externally on the surface of the pipe and which generate pulses that pass through the pipe wall.

Size: 1¡å~48¡å(25mm~1200mm)
Flow Range:¡À0.01 m/s~ ¡À12 m/s
Accuracy: ¡À1%
Repeatability: 0.2%
Output: 4-20mA, RS485
Power supply: Internal lithium 3000mAh
Transducer: IP68

Connecting module and secondary meter through RS-485 interface, transmission distance up to 1000m
Powerful Functions
Current output: 4-20mA, one channel, can be used for flow/heat transmitter;
OCT output: two channels, can be used for flow /heat switch;
Current input: 4-20mA, three channels, can be used for data collector;
Tri-wire resistance signal input (PT100): two channels, can be used for calorimeter.
Pipe Size: 15mm – 6,000mm
Rate Units: English(U.S) or metric
Liquid Types: Virtually all liquids
Display: 2*10backlit LCD,displaying instant
Transducers: Clamp-on type,insertion type ,in line type.
Operating Power: Isolation 8-36VDC
Communication: InterfaceRS-485

QTDS-100F wall mounted ultrasonic water flowmeter sensor heat meter adopts the self-development measurement technology.This measurement technique is a faster and more accurate process time measurement algorithm. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring single clean liquids Power supply: 24VDC/85VAC-2265AC Communication: RS485

China wall-mounted ultrasonic water flow meter price is an ultrasonic flowmeter used to measure the flow rate of liquids in closed pipes. The transducer is clamp-on type, which will provide the benefits of contamination-free operation and ease of installation. The transit time flowmeter includes two transducers, which act as ultrasonic transmitters and receivers. The transducer can be installed in a v-type method, where the sound travels through the pipe twice, a w-type method, where the sound travels through the pipe four times. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring clean liquids Power supply: 24VDC/85VAC-2265AC Communication: RS485

According to market request,the power supply can 24VDC or 220VAC or solar powered;Current the solar powered ultrasonic flow meter is more popular,beacuse solar powered meets international requirements, energy saving and environmental protection.
Accuracy:±1.0%
Heat measurement
Carbon steel body

Handheld Ultrasonic Flow Meter Clamp on Water ultrasonic Flow meter price is a portable liquid flow measurement device with a sensor.Handheld Ultrasonic Flow Meter Clamp on Water ultrasonic Flow meter price proven transit-time ultrasonic measurement technology for superior accuracy and ease of installation and installation. This easy-to-use flowmeter comes in a rugged, waterproof carrying case for easy transport of the display, sensor, and cables between measurement locations. High accuracy +/-1.0% of FS Transducer temperature: -30~90¡ãC/-30¡ãC~160¡ãC Measuring clean liquids Battery-powered,for 12 hours Communication: RS232

PLCM series ultrasonic open channel ultrasonic flow meter can directly display the instantaneous and cumulative flow, it is good for waster water measuring also a good river flow meter. The product supports weirs or notches of different standards in various countries and can be widely used for measurement or monitoring of total water drainage. The measurement result is not affected by the water quality.
Sensor Level Range: 0-4.0m; other level range also available
Blind zone: 0.20m
Temperature Compensation: Integral in probe
Pressure Rating: 0.2MPa
Beam Angle: 8* (3db)
Cable Length: 10m standard (can be extended to 1000m)
Sensor Material: ABS, PVC or PTFE (optional)
Sensor Protection Class: IP68