liquid turbine flowneter Intelligent Paddle Wheel Flowmeter

Turbine flowmeter is a precision flow measuring instrument, which can be used to measure the flow and total amount of liquid when matched with the corresponding flow totalizer. It is widely used in metering and control systems in petroleum, chemical, metallurgy, scientific research and other fields. Turbine flow sensors with sanitary fittings can be used in the pharmaceutical industry. The structure of the integrated turbine flowmeter is explosion-proof and can display the total flow, instantaneous flow and percentage of full flow.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%/¡À0.2%;
OUTPUT: PULSE/4-20mA;
Digital Communication:RS485, MODBUS; HART

turbine flowmeter is a kind of speed flowmeter. The sensor of turbine flow meter has the advantages of simple structure, lightweight, high precision, good reproducibility and quick response. It is widely used in petroleum, chemical industry, metallurgy, water supply, papermaking and other industries. It is the best choice for flow measurement and energy saving.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%;
OUTPUT: PULSE+4-20mA;
Digital Communication:RS485, MODBUS; HART
LCD display

Gas impeller flow meters are with the feature of low pressure loss, high accuracy, low initiating flow, and widely range ratio etc. Turbine gas meters provide consistently consistently accurate results in measuring clean gas within a variety of applications.

Size:DN25-400mm
Material:Aluminum alloy or stainless steel
Dual Power:3.6V battery powered+DC24V
Output:4-20mA,Pulse,RS485
Accuracy:1.5% or 1.0%

liquid turbine flow meter is a new generation turbine flow meter which was designed with advanced flow technologies both home and aboard. The product possesses advantages of simple structure, light in weight, high accuracy, good repeatability, short response time, easy installation, etc. It could be used widely in measurement of closed pipe system for pure liquid that will not react with 1Cr18Ni9Ti, 2Cr13, Al2O3 and hard alloys.

turbine flowmeter can be applied to alcohol, toluene, etc. which are not electrically conductive. And it can be used also in oil and gas, power plants, pharmaceutical and pulp & paper-making industry. However, it is recommended to not use for fluids containing sludge or highly viscous fluids. Also, it can be provided in flange type or screw (male or female) type while being able to cope with various piping conditions.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%/¡À0.2%;
OUTPUT: PULSE/4-20mA;
Digital Communication:RS485, MODBUS; HART

Turbine flow meter is the most popular equipment to measure flow electronically. Offer a wide flow and application rangeability. Turbine Flow Meters are easy to maintain, durable and versatile.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%;
OUTPUT: PULSE+4-20mA;
Digital Communication:RS485, MODBUS; HART

Turbine flow meters are used to measure clean, dry gases and liquids such as hydrocarbons, chemicals, gases and vapors, fuels and other types of liquids with lower viscosity, and for applications requiring highly accurate and precise measurements.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%/¡À0.2%;
OUTPUT: PULSE/4-20mA;
Digital Communication:RS485, MODBUS; HART

Liquid turbine flowmeter as precision instruments for industrial measurement. turbines turbine flowmeters with the advantages of simple structure, light weight, high precision, good reproducibility, sensitive response, and convenient installation, maintenance and use.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%;
OUTPUT: PULSE+4-20mA;
Digital Communication:RS485, MODBUS; HART

Turbine flowmeter is kind of cheap flowmeter. Used to measure liquid which has no chemical corrosive reaction, diesel etc.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%;
OUTPUT: PULSE+4-20mA;
Digital Communication:RS485, MODBUS; HART

Turbine flowmeter is a kind of speed meter, which has the advantages of high precision, good repeatability, simple structure, high pressure resistance, wide measurement range, small size, light weight, small pressure loss, long life, simple operation, convenient maintenance, etc. It is used to measure the volume flow and cumulative flow of low-viscosity, non-corrosive, clean liquids in closed pipelines. Can be widely used in petroleum, chemical, metallurgy, organic liquid, inorganic liquid, food, medicine and other industries
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%/¡À0.2%;
OUTPUT: PULSE/4-20mA;
Digital Communication:RS485, MODBUS; HART

turbine flowmeter Calibration of the device is carried out in laboratory conditions on the water.
If the device is supposed to be used in a viscous medium (2-300 cSt, centistokes), liquids with properties similar to those of the working medium are taken for calibration.
As a result, for each purpose and medium its own K-factor is assigned. Sometimes, manufacturers add ready-made universal viscosity charts for calibration to its equipment kit. Using them, a user can quickly determine already calculated K-factor for different substances.

Turbine Flowmeters draw the leading technology integrating with advanced design to produce the new generation of turbine flowmeter with the features of simple structure, light weight, high accuracy, good repeatability, flexible reaction, convenient installation/maintenance/application etc.. It is widely applied to measuring the liquid of which kinematic viscosity is under 5*10-6©O/s and have no impurify of fibre,grain etc.,and no corrosive interaction with the stainless steel 1Cr18Ni9Ti,2Cr13,and A12O3, and hard alloy in seal pipes
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%;
OUTPUT: PULSE+4-20mA;
Digital Communication:RS485, MODBUS; HART
LCD display

QTWG turbine gas meter is a type of high-precision custody transfer metering. As a ideal flow measurement device for natural gas or other non-corrosive gases applications, gas turbine flow meter urbine could be automatically pressure and temperature compensation to obtain volumetric measurements in standard units.

Size:DN25-400mm
Material:Aluminum alloy or stainless steel
Dual Power:3.6V battery powered+DC24V
Output:4-20mA,Pulse,RS485
Accuracy:1.5% or 1.0%

Turbine Flow Meter is a volumetric measuring turbine type of Impeller Flow meters , made up of Sensor and Convertor. The flowing fluids engages the rotor causing it to rotate at an angular velocity proportional to the fluid flow rate.The Sensor reacts to the average velocity of fluid with multi-blades rotor so as to speculating the flow value and the accumulative flow value.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%;
OUTPUT: PULSE+4-20mA;
Digital Communication:RS485, MODBUS; HART
LCD display

The liquid turbine flowmeter has small pressure loss, the impeller has anti-corrosion function, has strong anti-magnetic interference and vibration ability, reliable performance, long life, strong function of the whole machine, low power consumption. If it is matched with the display instrument with special functions of our company, It can also carry out quantitative control, excess alarm, etc.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%/¡À0.2%;
OUTPUT: PULSE/4-20mA;
Digital Communication:RS485, MODBUS; HART

turbine flow meter is a volumetric metering the meter consists of a rotor and bearing assembly Suspended on a shaft, which is mounted to a support device.
magnetic or modulated pick-off sensor is used to detect the passage of each rotor blade and generate a frequency output. The frequency output can be read directly with the end users electronics or further processed to convert to a linear analog flow Rate output.
Turbine flow meters are used to measure clean, dry gases and liquids such as hydrocarbons, chemicals, gases and vapors, fuels
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%/¡À0.2%;
OUTPUT: PULSE/4-20mA;
Digital Communication:RS485, MODBUS; HART

liquid turbine flow meter is a new type of intelligent instrument with integrated turbine flow sensor and display product calculation developed by advanced ultra-low power single-chip microcomputer technology, which has obvious advantages such as compact mechanism, clear reading, high reliability, undisturbed by external power supply, lightning resistance and low cost.

Turbine flowmeters are flow measurement instruments which use axial fluid momentum to turn a multibladed rotor, the angular velocity of which is approximately proportional to the volume flowrate. With appropriate calibration and operation, turbine meters offer precise and highly repeatable measurement of throughput and flowrate.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%/¡À0.2%;
OUTPUT: PULSE/4-20mA;
Digital Communication:RS485, MODBUS; HART

The turbine flowmeter is manufactured with advanced technology and is one of the most ideal flowmeters for measuring liquids. It has the characteristics of simple structure, high measurement accuracy, long service life, simple operation and easy maintenance. The product is divided into two series for measuring liquid and gas flow. It is widely used in metallurgy, chemical industry, petroleum, environmental protection, food and other industrial fields, and can reliably measure the volume flow of water, diesel, gasoline, low-viscosity crude oil and other liquids and various gases.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%/¡À0.2%;
OUTPUT: PULSE/4-20mA;
Digital Communication:RS485, MODBUS; HART

Sanitary turbine flow meters have stainless steel bodies and come standard with Tri-Clover fittings. Sanitary flow meter is suitable for measuring liquid without impurities. It can output pulse frequency signal. It is used to detect instantaneous flow and total integrated flow. Sanitary flow meter can be used in food, sport drink, liquor and other beverage industries, in preprocess applications.

Turbine flowmeters utilize flow measurement technology to render exceptionally reliable and accurate digital outputs. Our high-quality industrial flowmeters are maintainable, durable, and versatile. These versatile turbine flowmeters measure an extensive range of liquids, vapors in pipes, such as chemicals, hydrocarbons, cryogenic liquids, water, and industrial gases.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%/¡À0.2%;
OUTPUT: PULSE/4-20mA;
Digital Communication:RS485, MODBUS; HART

Turbine flowmeter measures the flowrate from the number of revolutions of a blade placed in the flow. The speed of revolutions of the blade with an axis parallel to the flow direction is proportional to the speed of the flow. Utilizing the capability of highly accurate measurement for wide range of viscosity, the turbine flowmeter is useful for process control, transactions as well as process control of petroleum products, general chemical fluids, liquefied gas, water, etc.

QTWG series turbine gas meter is an ideal flow instrument to measure natural gas in industrial and commercial billing applications. Natural gas flow meters provide various kinds of outputs including 4-20mA, pulse and RS485 easily connect into user control systems.

Size:DN25-400mm
Material:Aluminum alloy or stainless steel
Dual Power:3.6V battery powered+DC24V
Output:4-20mA,Pulse,RS485
Accuracy:1.5% or 1.0%

QTWG series gas turbine flow meters adopt import impeller material which could ensure high accuracy in working life. Designed to perform on the high level of accuracy, turbine gas flow meters are ideal product for commercial and industrial uses.

Size:DN25-400mm
Material:Aluminum alloy or stainless steel
Dual Power:3.6V battery powered+DC24V
Output:4-20mA,Pulse,RS485
Accuracy:1.5% or 1.0%

liquid turbine flow meter adapts to measure the liquid rate and total flowrate of low viscosity. It can be widely used in the fields of Petrol, Chemical industry, Metallurgy, for measuring or control.
Turbine flowmeter sensors are typically located external to the flowing stream to avoid material of construction constraints that would result if wetted sensors were used. When the fluid moves faster, more pulses are generated. The transmitter processes the pulse signal to determine the flow of the fluid. Transmitters and sensing systems are available to sense flow in both the forward and reverse flow directions.

Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%/¡À0.2%;
OUTPUT: PULSE/4-20mA;
Digital Communication:RS485, MODBUS; HART

liquid turbine flowmeter, as fluid flows through turbine rotor and drives it to rotate, the rotating rotor periodically cuts magnetic field line to generate electric pulse signal, which can be transmitted to output and transferred to the meter to display flow rater or totalizer. It features in high accuracy, good repeatability, simple structure, low pressure loss, convenient maintenance, etc. It is ideal to measure the volume of low-viscosity liquids in closed pipes, such as tap and demineralized water, fuels, liquefied gases, light fuel oil, solvents, pharmaceutical fluids, food etc.

Turbine flowmeter measures the flowrate from the number of revolutions of a blade placed in the flow. The speed of revolutions of the blade with an axis parallel to the flow direction is proportional to the speed of the flow.the turbine flowmeter is useful for process control, transactions as well as process control of petroleum products, general chemical fluids, liquefied gas, water, etc.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%/¡À0.2%;
OUTPUT: PULSE/4-20mA;
Digital Communication:RS485, MODBUS; HART

The turbine flow meter is an ideal solution when high accuracy, compact size, fast response, and high tolerance to shock and vibration are critical requirements and suitable for wide range of viscosity medium including oil, gas, water and wastewater, chemical, gas utility, power, food and beverage, aerospace, pharmaceutical, etc.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%/¡À0.2%;
OUTPUT: PULSE/4-20mA;
Digital Communication:RS485, MODBUS; HART

turbine flow transducer adapts to measure the liquid rate and total flowrate of low viscosity. It can be widely used in the fields of Petrol, Chemical industry, Metallurgy, Scientific research for measuring or control. Several output and display methods can be selected.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%;
OUTPUT: PULSE+4-20mA;
Digital Communication:RS485, MODBUS; HART

Turbine Flowmeter’s advantages : simple structure , less processing components, light weight, convenient maintenance, is the general type of flowmeter, superior performance, high precision, anti magnetic interference, 540 rotating convenient reading
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%;
OUTPUT: PULSE+4-20mA;
Digital Communication:RS485, MODBUS; HART
LCD display