Irrigation water meter 4-20mA output ultrasonic open channel flow meter

With ultrasonic flow meters, the flow of liquids can be measured reliably – independent of conductivity, pressure, temperature, and in applications where traceability and guaranteed accuracy are required, the external ultrasonic sensor is the first choice. Clamp-on ultrasonic sensors, on the other hand, are mounted on the outer wall of the pipe and can therefore also be used for temporary measurements.
Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring clean liquids Built-in rechargeable battery 3.6V Communication: RS232

Ultrasonic flow measurement according to the ¡°differential transit time¡± method: This method uses two sensors, set opposite each other in the measuring tube. Each sensor can alternately transmit and receive ultrasonic signals, while simultaneously measuring the signal transit time.
Measuring cycle:50mS
Output:4~20mA,Pulse,OCT,RS485
Body material:Standard carbon steel,SS304 and SS316 are optional
Power supply:DC24V and AC220V

QT811 clamp on ultrasonic flow meter is a type of non-invasive flowmeters work on the transit time ultrasonic principle. This involves sending and receiving ultrasonic pulses from a pair of sensors and examining the time difference in the signal. Suitable for various liquids and compatible with various pipeline materials and sizes.

Pipe Size:?DN15-DN40mm (1/2¡±~1 1/2¡±)
Flow Range:¡À0.1m/s ~¡À5m/s
Temperature: 0~75¡æ (standard)
Output: 4-20mA, OCT Pulse, RS485
Accuracy:?¡À1% of measured value
Power Supply: DC10-24V

Ultrasonic Flowmeter Portable Clamp on Ultrasonic Flow Meter is a non-contact instrument, which can measure the flow of medium with large diameter and can also be used for the measurement of medium that is not easy to contact and observe. Its measurement accuracy is very high, and the external clip-type installation can reach the highest accuracy of ¡À1.0%. It is almost not disturbed by various parameters of the measured medium, especially it can solve the strong corrosiveness, non-conductivity, Flow measurement of radioactive and flammable and explosive media. Measuring accuracy: +/-1.0% of FS Transducer temperature: -30~90¡ãC/-30¡ãC~160¡ãC Measuring clean liquids Battery-powered,for 12 hours Communication: RS232

Clamp on ultrasonic flow meter are widely used in tap water, heating, water conservancy, metallurgy, chemical industry, machinery, energy and other industries. Portable Hand Held Ultrasonic Flow Meter can be used for production monitoring, flow verification, temporary detection, flow inspection, water meter balance debugging, heat network balance debugging, and energy-saving monitoring. Measuring accuracy: +/-1.0% of FS Transducer temperature: -30~90¡ãC/-30¡ãC~160¡ãC Measuring clean liquids Battery-powered,for 12 hours Communication: RS232

Measuring Pipe Size DN15-DN6000 Wall Water Mounted Ultrasonic Flow Meter is a high precision no-cut tube measurement method. This special design includes matching sensors for ease of use and is ideal for installation in existing systems Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring single clean liquids Power supply: 24VDC/85VAC-2265AC Storage: SD card optional Heat meter optional

QT621 handheld type ultrasonic water flow meter adopt transit-time principle.Portable ultrasonic flow meter support precise bidirectional and highly dynamic flow measurement with the non-invasive clamp-on technology. Portable ultrasonic flow meter mainly applies for measuring the flow of homogeneous medium fluid .

Size: 1¡å~48¡å(25mm~1200mm)
Flow Range:¡À0.01 m/s~ ¡À12 m/s
Accuracy: ¡À1%
Repeatability: 0.2%
Output: 4-20mA, RS485
Power supply: Internal lithium 3000mAh
Transducer: IP68

QT621 ultrasonic flow meter is a portable type flow meter for non-invasive, quick flow and energy measurement with clamp-on technology for many types of piping.
Portable type ultrasonic flow metere can be easily moved and installed in different pipes and convenient to carry site to site.

Size: 1¡å~48¡å(25mm~1200mm)
Flow Range:¡À0.01 m/s~ ¡À12 m/s
Accuracy: ¡À1%
Repeatability: 0.2%
Output: 4-20mA, RS485
Power supply: Internal lithium 3000mAh
Transducer: IP68

Widely used in Running water,Heating, Water conservation,Metallurgy,Chemical industry,Machinery,Energy etc.

Modular Flow Meter is in market in various sizes, designs and shapes. It is highly appreciated for their long functional life.The main unit has the advantages of small size, complete functions and low price. Using guide rail installation, it is suitable to be installed in instrument box or distribution box.
Linearity: 0.5%
Repeatability: 0.20%
Accuracy: Better than ¡À1% for velocity above 0.2m/s
Response Time: 0-999 second, user-configurable
Flow Range: ¡À32m/s
Measuring Pipe Size: 25mm-6000mm
Units: English(U.s.) or metric
Totalizer: 7-digit totalizer for net, positive and negative flow respectively

Digital Wall Mounted Clamp on Ultrasonic Flowmeter Flow Meter is simple to install and is suitable for large diameter pipes requiring monitoring and flow measurement, as well as a wide network of smaller supply linesDigital Wall Mounted Clamp on Ultrasonic Flowmeter Flow Meter provide the tools needed to meet the diverse requirements of such a demanding industry. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring clean liquids Power supply: 24VDC/85VAC-2265AC Communication: RS485

Digital Ultrasonic Water Flowmeter Wall Mounted Relay alarm and RS485 Modbus flow meters can realize to measure flow.Connect with temperature sensor,it can measure heat flow.

QT621 handheld ultrasonic flow meter support to carry from site to site conveniently. Support accurate bidirectional and highly dynamic flow measurement with the non-invasive clamp-on technology. Portable ultrasonic flow meter mainly applies for measuring the flow of homogeneous medium fluid in the water injection flow measurement, raw water flow measurement, tap water flow measurement etc.

Size: 1¡å~48¡å(25mm~1200mm)
Flow Range:¡À0.01 m/s~ ¡À12 m/s
Accuracy: ¡À1%
Repeatability: 0.2%
Output: 4-20mA, RS485
Power supply: Internal lithium 3000mAh
Transducer: IP68

Clamp on type sensor ultrasonic water flow meter no pipe cutting required. The user simply clamp on the flow sensor to the pipe surface. Clamp on type sensor ultrasonic water flow meter can then detect the flow through ultrasonic waves, and then automatically calculate the flow rate value, flow accumulator, etc. No pipe cutting means no damage to the pipe. So as long as the pipes are in good condition, the installation on the flowmeter will not provide the possibility of leakage. Sensor: Clamp-on/External Principle: transmit time Size: DN15mm-DN6000mm Measuring medium: Liquid 3.6V Battery-powered

Q&T portable ultrasonic flow meters involves sending and receiving ultrasonic pulses from a pair of sensors and examining the time difference in the signal. Portable ultrasonic flow meter can be easily moved and installed in different pipes and convenient to carry site to site, which is very convenient for users to monitor the data.

Size: 1¡å~48¡å(25mm~1200mm)
Flow Range:¡À0.01 m/s~ ¡À12 m/s
Accuracy: ¡À1%
Repeatability: 0.2%
Output: 4-20mA, RS485
Power supply: Internal lithium 3000mAh
Transducer: IP68

A non-contact ultrasonic water flow meter that is designed for open channel flow metering, whether you have a flume, weir or any other primary device. This meter has 4-20mA, RS485 and relay output,which is a good choice for different needs of open channel flow measuring.

Analogue?Output: 4-20mA,?corresponding?to?instantaneous?flow
Relays?Output: Standard?2?relay?outputs(Optional?up?to?6?relays)
Serial?Communication: RS485,?MODBUS?-RTU?standard?protocol
Ambient?Temperature: -40 ~70 Degree C
Measure?Cycle: 1?second?(selectable?2?seconds?)
Power?Supply: DC24V?(+5%)?0.2A;?AC220V?(+20%)?0.1A?;Optional?DC12V

Wall Mounted ultrasonic water flow meter is an ultrasonic flowmeter used to measure the flow rate of liquids in closed pipes. The transducer is a non-contact, clamp-on type, which will provide the benefits of contamination-free operation and ease of installation. The transit time flowmeter employs two transducers, which act as ultrasonic transmitters and receivers. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring clean liquids Power supply: 24VDC/85VAC-2265AC Communication: RS485

Q&T brand ultrasonic flow meter is real flow calibrated,5 flow velocity point and calibrate 3 times for each flow velocity point.Q&T calibration device can calibrate from DN3~DN3000mm,and adopt Seimens,Rosemount,E+H brand flow meter as the standard meter.
Single channel ultrasonic flow meter accuracy <1.0% Multi-channel ultrasonic flow meter caccuracy can reach 0.5%

Digital Ultrasonic flowmeter DN15 to DN6000mm Ultrasonic Flow meter is a high precision no-cut tube measurement method. This special design includes matching sensors for ease of use and is ideal for installation in existing systems Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring single clean liquids Power supply: 24VDC/85VAC-2265AC Storage: SD card optional Heat meter optional

New Version Protable Ultrasonic Water Flowmeter Price For Sale,Ultrasonic Flow Meter is a portable liquid flow measurement device with a sensor. New Version Protable Ultrasonic Water Flowmeter Price For Sale,Ultrasonic Flow Meter adopt transit-time ultrasonic measurement technology for superior accuracy and ease of installation and installation. This easy-to-use flowmeter comes in a rugged, waterproof carrying case for easy transport of the display, sensor, and cables between measurement locations. High accuracy +/-1.0% of FS Transducer temperature: -30~90¡ãC/-30¡ãC~160¡ãC Measuring clean liquids Battery-powered,for 12 hours Communication: RS232

ultrasonic water flow meters RS485 digital water flow meter clamp on ultrasonic portable liquid flow meter is controlled by a micro-processor system which contains a wide range of data that enables it to be used with pipes with an outside diameter ranging from 15mm up to 1200mm (depending on model) and constructed of almost any material. instrument will also operate over a wide range of fluid temperatures

QTDS-100H Sea Water Ultrasonic Flowmeter incorporates the latest ultrasonic technology to give you an accurate, easy to use hybrid flow meter with transit-time operating modes. With their quick and easy clamp-on transducer installation, factory pre-configuration and user programmable menu driven interface, the ultrasonic flow meters are a snap to commission in the field. The reliable QTDS-100H Sea Water Ultrasonic Flowmeter use custom algorithms and technology to ensure high accuracy flow metering.
Accuracy: +/-1.0% of FS
Wide range: DN15mm-DN6000mm
Medium: clean liquids,pure water
Built-in rechargeable battery 3.6V
Communication: RS232

High Frequency portable clamp on ultrasonic flow meter no pipe cutting required. The user simply clamp on the flow sensor to the pipe surface. The High Frequency portable clamp on ultrasonic flow meter can then detect the flow through ultrasonic waves, and then automatically calculate the flow rate value, flow accumulator, etc. No pipe cutting means no damage to the pipe. So as long as the pipes are in good condition, the installation on the flowmeter will not provide the possibility of leakage. Sensor: Clamp-on/External Principle: transmit time Size: DN15mm-DN6000mm Measuring medium: Liquid 3.6V Battery-powered

QT621 portable type ultrasonic clamp on flow meters use clamp-on transducers that are mounted externally on the surface of the pipe and which generate pulses that pass through the pipe wall.
Portable ultrasonic flow meters can be easily moved and installed in different pipes and convenient to carry site to site, which is very convenient for users to monitor the data.

Size: 1¡å~48¡å(25mm~1200mm)
Flow Range:¡À0.01 m/s~ ¡À12 m/s
Accuracy: ¡À1%
Repeatability: 0.2%
Output: 4-20mA, RS485
Power supply: Internal lithium 3000mAh
Transducer: IP68

Clamp-on ultrasonic flow meters showcase the benefits of digital signal processing: market-leading accuracy, noise immunity and reliability,liquid ultrasonic flow meter popular in many industry. Flow range:± 0.09ft/s ~ ±16ft/s (±0.03m/s ~ ±5m/s);
Outputs:Analog output:4~20mA,max load 750Ω,Pulse output: 0~10KHz;
Communication: RS232/RS485 Mod bus:
Power supply:10~36VDC/1A;
Display:240*128 back lit LCD;

Handheld Ultrasonic Flowmeter Clamp on Flow Meter Portable Liquid Flow Meter with small transducer use ultrasonic technology to measure the velocity of the liquid. Ultrasonic meters are avaiable as clamp-on solutions. Non pipe cutting, this ultrasonic flow meters can display velocity and accumulated flow. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Medium: clean liquids,pure water Built-in rechargeable battery 3.6V Housing Material: ABS

Ultra low price Instant delivery magnetic flow meter manufacturer provide you with an accurate, easy-to-install flow meter. wall mount flow sensor feature quick, easy clamp-on sensor installation, configuration, and a user-programmable menu-driven interface for easy commissioning in the field. Ultra low price Instant delivery magnetic flow meter manufacturer use a special technology to ensure highly accurate flow measurement. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring single clean liquids Power supply: 24VDC/85VAC-2265AC Storage: SD card optional Heat meter optional

China wall mounted Clamp on pipe ultrasonic water flow meter price is a high precision no-cut tube measurement method. This special design includes matching sensors for ease of use and is ideal for installation in existing systems Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring single clean liquids Power supply: 24VDC/85VAC-2265AC Storage: SD card optional Heat meter optional

QT811 ultrasonic flow meter support accurate bidirectional and highly dynamic flow measurement with the non-invasive clamp-on technology. Clamp on small size flow meter is a type of small size instrument for non-invasive, quick flow and energy measurement with clamp-on technology for many types of piping.

Pipe Size:?DN15-DN40mm (1/2¡±~1 1/2¡±)
Flow Range:¡À0.1m/s ~¡À5m/s
Temperature: 0~75¡æ (standard)
Output: 4-20mA, OCT Pulse, RS485
Accuracy:?¡À1% of measured value
Power Supply: DC10-24V

This transit-time open Channel flow meter can be used for continuous measuring of municipal rain-water, wastewater, sewage discharge and irrigation water pipelines. This Open Channel flow meter measures level, flow rate and total volume of water flowing through weirs, flumes, and channels etc.

Specifications:
Display: Backlight?LCD
Flow?Rate?Range: 0.0000~99999L/S?or?m3/h
The?maximum?of Accumulative Flow: 9999999.9?m3/h
Accuracy?of?Change in Level: 1mm?or?0.2%?of?full?span?(whichever?is?greater)
Resolution: 1mm
Analogue?Output: 4-20mA,?corresponding?to?instantaneous?flow
Relays?Output: Standard?2?relay?outputs(Optional?up?to?6?relays)
Serial?Communication: RS485,?MODBUS?-RTU?standard?protocol