IP68 protection 10m cable remote type inline magnetic flow meter

Q&T series Electromagnetic flowmeter follows the faraday law of electromagnetic induction.When the conductive liquid flows through the electromagnetic flowmeter,the induced electromotive force will be produced in the conductor,and the induced electromotive force is directly proportional to the velocity of conductive liquid,magnetic flux density and width of conductor(inside diameter of flowmeter,such induced electromotive force is detected by a pair of electrodes on the tube wall of the flowmeter,and the rate of flow can be acquired by mathematical operation.
Size: 1/8″-120″
Accuracy: ±0.5%
Electrode: SUS316L, Hastelloy B, Hastelloy C
Structure: compact, remote
Liner: PTFE, PFA, Polyurethane, Neoprene, Hard Rubber, Ceramic
Output Signal: 4~20 mA, Pulse
Communication: RS485, HART, PROFIBUS
Protection Grade: IP65 std, IP68 optional for remote
Velocity: 0.1~15 m/s
Conductivity: > 5 μS/cm, demineralized water > 20 µS/cm
Power supply: 85~250 VAC, 20V~36VDC, 3.6V lithium battery
Size: DN3-DN3000
Sensor material: carbon steel (std), SS304 / SS316 (optional)
Flange: ANSI, DIN, JIS, etc.
Measuring tube: SS304
Function: High and low alarm, exciting alarm, empty pipe alarm, self-diagnosis

No Moving Parts
RS485 Standard,HART standard is available.
Suitable for Pipes Up to DN300
Pulse, Gprs output
Standard 5 points calibration Included

QTLD/C isnertion magnetic flow meter can be installed without cutting off flow.

water flow meter can be calibrated 8 pcs at the same time, while 5 points flow will be calibrated, all test bench has been approved ISO 17025.

Easy Setup
Minimal Straight Pipe
Forward or Reverse flow and Total
IP65,IP67 ,IP68 Rated (optional)
Virtually No Pressure Loss

flange connection magnetic flow meter can display Instantaneous flow, total flow, flow velocity. mag flowmeters have function of high and low alarm, empty pipe alarm, exciting alarm and self-diagnosis.
Structure: compact, remote
Size: DN3-DN3000
Communication: RS485, HART, PROFIBUS
Protection Grade: IP65 std, IP68 optional for remote

Q&T’s battery magnetic flow meter comes standard with a rugged IP68 die-cast aluminum enclosure,which allows the device to be used in both indoor and outdoor applications. Size: DN10-DN2000; Accuracy: ¡À0.5% (Standard), ¡À0.3% or ¡À0.2% (Optional); Protection Class: IP65(Standard),IP68(Optional for remote type); Process Connection: Flange(Standard),Wafer,Thread,Tri-clamp etc(optional); Output Signal: 4-20mA / pulse (optional); Communication: RS485(Optional),HART(Optional),GPRS/GSM(Optional); Power Supply: Battery powered 3.6V, Battery powered 3.6V +DC24V(Optional); Power Consumption: 0.5W(Standard), 1.5W(with DC24V);

1. Instrument display and output functions are complete, it can display instantaneous flow, flow rate, cumulative flow and other data, and has RS485 interface (optional);
2. With GSM and GPRS wireless data remote transmission function (optional);
3. It has the functions of timing, counting and clocking out of power

With simple structure ,the flow meter is of high reliability without lining in the
measuring pipe .
The wide range of the nominal bore is suitable for all the pipe size between
DN2 and DN600.
Measurement is independent of fluid density ,viscosity ,humidity ,temperature
pressure and conductivity.

alll QTLD waste water flow meter can be calibrated according to CNAS ISO 17025.. pressure of QTLD water flow emter can be ANSI 150#, 300#, 600#, 900#, etc. all waste water flow meter will be tested by pressure equipment. magnetic flowmeter is calibrated by ISO/IEC 17025:2016 CNAS Approved Test Bench.

Conductivity: > 5 ¦ÌS/cm, demineralized water > 20 ¦ÌS/cm
Size: DN3-DN3000
Sensor material: carbon steel (std), SS304 / SS316 (optional)
Measuring tube: SS304
Function: High and low alarm, exciting alarm, empty pipe alarm, self-diagnosis

DC3.6V powered electromagnetic flow meter is an ideal solution for nearly any water manager, 3.6V battery meter eliminates the need for AC/DC power connection. Size: DN10-DN2000; Protection Class: IP65(Standard),IP68(Optional for remote type); Process Connection: Flange(Standard),Wafer,Thread,Tri-clamp etc(optional); Output Signal: 4-20mA / pulse (optional); Communication: RS485(Optional),HART(Optional),GPRS/GSM(Optional); Power Supply: Battery powered 3.6V, Battery powered 3.6V +DC24V(Optional); Power Consumption: 0.5W(Standard), 1.5W(with DC24V); Alarm: Upper limit alarm / lower limit alarm

Forward and reverse flow measurement.
Measure pulp and slurry, water and wastewater, food and beverage, acid and alkaline.
Multiple output communication (pulse, GPRS, RS485),

magnetic flow meter is mainly used to measure conductive liquids, mag flowmeter has compact and remote structurer. protection grade of remote type flow sensor is IP68, it can be submerged in the water. Liquid flow meter is widely used in Sewage Treatment Plant Water Supply project and Steel & Aluminum Industries, Chemical & Fertilizer Industries. Q&T brand electromagnetic water meter has been approved ATEX explosion proof certificate. which can be used any conductivity is higher than 20 ¦ÌS/cm.
Structure: compact, remote
Output Signal: 4~20 mA, Pulse
Communication: RS485, HART, PROFIBUS
Velocity: 0.1~15 m/s
Power supply: 85~250 VAC, 20V~36VDC, 3.6V lithium battery

inline magnetic flow meter has no mechanical inertia, has a sensitive response, can measure instantaneous pulsating flow, and has good linearity. Our mag flow meters have an accuracy over a wide flow range that can often exceed ¡À 0.5% of flow rate. Our MAG flow meters are ideal for liquids.

Size: 1/8″-120″
Accuracy: ¡À0.5%
Repeatability: 0.17%
Electrode: SUS316L, Hastelloy B, Hastelloy C
Structure: compact, remote

waste water electromagnetic flow meter waste water electromagnetic flow meter sensors and converters in two parts. The product is based on Faraday’s law of electromagnetic induction, used to measure the conductance greater than 20 μS / cm volume of conductive liquid flow,
Medium temperature:
Integral type : -20℃~60℃
Remote type(Rubber&Polyurethane liner): -10℃~80℃
Remote type (PTFE&PFA&F46 liner): -10℃~160℃
♦ Integrated verification,diagnostic function and empty pipe detection.
♦ Measure forward and reverse direction flows.
♦ Built-in reference electrodes,no need to connect ground ring.

Battery operated electromagnetic flow meter satisfy water fee calculation with high accuracy, battery meter is widely used in applications without power grid, can work with solar power supply. Accuracy: ¡À0.5% (Standard), ¡À0.3% or ¡À0.2% (Optional); Ambient Humidity: 5-100%RH (relative humidity); Protection Class: IP65(Standard), IP68(Optional for remote type); Process Connection: Flange(Standard),Wafer,Thread,Tri-clamp etc(optional); Output Signal: 4-20mA / pulse (optional); Communication: RS485(Optional),HART(Optional),GPRS/GSM(Optional); Power Supply: Battery powered 3.6V,Battery powered 3.6V +DC24V(Optional); Power Consumption: 0.5W(Standard),1.5W(with DC24V);

Irrigation System Batch Control Flow Meter Water Electromagnetic Flowmeter is widely used because less obstruction, cost-effective and accurate measurement. Electromagnetic flow meter don’t have any moving parts to wear down, reducing the need for maintenance or replacement. We offer this digital water flow meter with a range of liners,electrodes, and sizes, which can meet various conductive liquids.

Specifications:
Structure: compact, remote
Liner: PTFE, PFA, Polyurethane, Neoprene, Hard Rubber, Ceramic
Output Signal: 4~20 mA, Pulse
Communication: RS485, HART, PROFIBUS
Protection Grade: IP65 std, IP68 optional for remote
Velocity: 0.1~15 m/s
Power supply: 85~250 VAC, 20V~36VDC, 3.6V lithium battery
Size: DN3-DN3000
Sensor material: carbon steel (std), SS304 / SS316 (optional)
Flange: ANSI, DIN, JIS, etc.
Measuring tube: SS304
Function: High and low alarm, exciting alarm, empty pipe alarm, self-diagnosis

mag flow meterinluding inserted flow and compact electromagnetic flow meter, while electromagnetic flow meters are designed to measure conductive liquids. Q&T instrument is OEM and OEM manufacturer of inline magnetic flowmeter with 17 years experience, standard cable length is 10m, widely used in water and waste water industry.

Structure: compact, remote
Output Signal: 4~20 mA, Pulse
Communication: RS485, HART, PROFIBUS
Velocity: 0.1~15 m/s
Power supply: 85~250 VAC, 20V~36VDC, 3.6V lithium battery

Electromagnetic flowmeters. Measuring for process management, revenue collection, liquid transportation and energy conservation. water flow meter is widely used because less obstruction, cost-effective and accurate measurement. Magnetic flowmeter don’t have any moving parts to wear down, reducing the need for maintenance or replacement.

Liner: PTFE, PFA, Polyurethane, Neoprene, Hard Rubber, Ceramic
Output Signal: 4~20 mA, Pulse
Communication: RS485, HART, PROFIBUS
Protection Grade: IP65 std, IP68 optional for remote
Velocity: 0.1~15 m/s

Battery magnetic flowmeter also could measure & display temperature and pressure, humanized human-computer interaction interface, battery mag flow meter enjoy easy operation. Nominal Pressure: 0.6-1.6MPa(2.5Mpa / 4.0Mpa /6.4Mpa…Max 42Mpa);
Accuracy: ¡À0.5% (Standard), ¡À0.3% or ¡À0.2% (Optional);
Liner: PTFE, Neoprene,Hard Rubber,EPDM,FEP, Polyurethane,PFA;
Electrode: SUS316L,Hastelloy B,Hastelloy C, Titanium,Tantalum,Platinum-iridium;
Structure: Integral,remote,submersible,ex-proof;
Process Connection: Flange(Standard),Wafer,Thread,Tri-clamp etc(optional);
Output Signal: 4-20mA / pulse (optional);
Communication: RS485(Optional),HART(Optional),GPRS/GSM(Optional);

electromagnetic flowmeter is calibrated by standard mass method by high accuracy calibration equipment. standard accuracy is ¡À0.5%, ¡À0.2% accuracy is optional, inline magnetic flow meter is calibrationed 5 points by comparison method or mass method. our calibration lab has been approved CNAS ISO/IEC 17025:2017.

Size: DN3-DN3000
Structure: compact, remote
Liner: PTFE, PFA, Polyurethane, Neoprene, Hard Rubber, Ceramic
Protection Grade: IP65 std, IP68 optional for remote
Power supply: 85~250 VAC, 20V~36VDC, 3.6V lithium battery
Sensor material: carbon steel (std), SS304 / SS316 (optional)

Liquid flow meter is widely used in Sewage Treatment Plant Water Supply project and Steel & Aluminum Industries, Chemical & Fertilizer Industries. Q&T brand electromagnetic water meter has been approved ATEX explosion proof certificate. which can be used any conductivity is higher than 20 ¦ÌS/cm.
Output Signal: 4~20 mA, Pulse
Communication: RS485, HART, PROFIBUS
Protection Grade: IP65 std, IP68 optional for remote
Velocity: 0.1~15 m/s
Conductivity: > 5 ¦ÌS/cm, demineralized water > 20 ¦ÌS/cm

Electromagnetic water meter is used to measure the flow of conductive fluid in watersupply,steel£¬petroleum,chemical industry,electric power£¬industry£¬water conservancyand other departments.

liner of tri-clamp electromagnetic flow meter is PFA, which is approved NSF, tri-clamp standard is 3A, 11851 is optional. QTLD/Ttri-clamp magnetic flow meter is designed for sanitary applications, size is DN15-DN200, the sensor isSS304 or SS316 and lined with PFA. With tri-clamp, the magnetic flow meter can be installed and torn down easilyto clear, it meet the strict requirements of food-processing and pharmaceutical industries.
Size: 1/8″-120″
Accuracy: ¡À0.5%
Structure: compact, remote
Output Signal: 4~20 mA, Pulse
Communication: RS485, HART, PROFIBUS
Velocity: 0.1~15 m/s

QTLD electromagnetic water meter is packed by wooden case or carbone box with foam to protect flow metes won’t be damaged in transit, we will rich stock, flowmeters will be delivered in 6 days.
water flow meter is widely used because less obstruction, cost-effective and accurate measurement. Magnetic flowmeter don’t have any moving parts to wear down, reducing the need for maintenance or replacement.
Repeatability: 0.17%
Electrode: SUS316L, Hastelloy B, Hastelloy C
Structure: compact, remote
Liner: PTFE, PFA, Polyurethane, Neoprene, Hard Rubber, Ceramic
Output Signal: 4~20 mA, Pulse

electromagnetic flow meter is calibrated by standard mass method by high accuracy calibration equipment. standard accuracy is ¡À0.5%, ¡À0.2% accuracy is optional.
Electromagnetic flow meter, or magmeter, are comprised of a transmitter and sensor that together measure flow.
Liner: PTFE, PFA, Polyurethane, Neoprene, Hard Rubber, Ceramic
Output Signal: 4~20 mA, Pulse
Communication: RS485, HART, PROFIBUS
Protection Grade: IP65 std, IP68 optional for remote
Velocity: 0.1~15 m/s

Q&T magnetic flowmeter are widely used for conductive liquids which conductivity is high than 20 ¦ÌS/cm, more economical option for large pipelines flow measurement, accuracy is ¡À0.5%. size is DN3-DN3000, which can be used various pipes.
Output Signal: 4~20 mA, Pulse
Communication: RS485, HART, PROFIBUS
Flange: ANSI, DIN, JIS, etc.
Measuring tube: SS304

Q&T’s DC3.6V powered mag flow meter everyone will have well calibrated before leave factory, battery meter adopt pulse calibration, with weighing method, guarantee the 0.5% accuracy. Accuracy: ¡À0.5% (Standard),¡À0.3% or ¡À0.2% (Optional); Liner: PTFE,Neoprene,Hard Rubber,EPDM,FEP,Polyurethane,PFA; Electrode: SUS316L,Hastelloy B,Hastelloy C,Titanium,Tantalum,Platinum-iridium; Ambient Temperature: -20¡æ~+ 60¡æ; Ambient Humidity: 5-100% RH (relative humidity); Process Connection: Flange(Standard),Wafer,Thread,Tri-clamp etc(optional); Output Signal: 4-20mA/pulse (optional);

3.6V battery powered electromagnetic flowmeter could reach IP68 protection, put under water for long time, 3.6V battery powered magnetic flowmeter also have external DC12-24V power. Size: DN10-DN2000; Nominal Pressure: 0.6-1.6MPa(2.5Mpa / 4.0Mpa /6.4Mpa…Max 42Mpa); Accuracy: ¡À0.5% (Standard), ¡À0.3% or ¡À0.2% (Optional); Structure: Integral,remote,submersible,ex-proof; Medium Temperature: -20¡æ~+60¡æ (integral type), Remote type(neoprene,Hard rubber,Polyurethane, EPDM) -10¡æ~+80¡æ; Remote type (PTFE / PFA / FEP)-10¡æ~+160¡æ; Protection Class: IP65(Standard),IP68(Optional for remote type); Output Signal: 4-20mA / pulse (optional); Communication: RS485(Optional),HART(Optional),GPRS/GSM (Optional);

Q&T series Intelligence Electromagnetic Flow Meter transmitter, together with magnetic-inductive sensor, forms a microprocessor-controlled accurate measurement unit. Q&T series Intelligence transmitter can be used for fluid flow speeds up to 15 m/s for a minimum conductivity of 5 S/cm.
Size: 1/8″-120″
Accuracy: ±0.5%
Electrode: SUS316L, Hastelloy B, Hastelloy C
Structure: compact, remote
Liner: PTFE, PFA, Polyurethane, Neoprene, Hard Rubber, Ceramic
Output Signal: 4~20 mA, Pulse
Communication: RS485, HART, PROFIBUS
Protection Grade: IP65 std, IP68 optional for remote
Velocity: 0.1~15 m/s
Conductivity: > 5 μS/cm, demineralized water > 20 µS/cm
Power supply: 85~250 VAC, 20V~36VDC, 3.6V lithium battery
Size: DN3-DN3000
Sensor material: carbon steel (std), SS304 / SS316 (optional)
Flange: ANSI, DIN, JIS, etc.
Measuring tube: SS304
Function: High and low alarm, exciting alarm, empty pipe alarm, self-diagnosis

Electromagnetic water meter GSM/GPRS remote monitoring management topology diagram 4. This system introduces more humanized management such as data backup, SIM card cost statistics and so on.