Industrial Type Digital 4 20Ma Output Liquid Flow Meter Chemical mag flowmeter

Standard cable length or remote or remote magnetic heat meter is 10m, max length is 120m, Pt1000 temerature sensor is configured. electromagnetic BTU meter is composed by transmitter, sensor and PT1000 temperature sensor, insertion magnetic flowmeter can configure thread or flange ball valve to be hot-tapped, which allows sensor to be installed and retracted from process piping without shutting down the process.

Electrode: SUS316L, Hastelloy B, Hastelloy C
Structure: compact, remote
Liner: PTFE, PFA, Polyurethane, Neoprene, Hard Rubber, Ceramic
Output Signal: 4~20 mA, Pulse
Communication: RS485, HART, PROFIBUS

magnetic flow meters can be calibrated 5 pcs once time. liquid flow meter is calibrated on ¡À0.2% accuracy test bench, liquid flow meters are calibrated by mass method, comparison method, The operating voltage and frequency range of the calibrator must match those of the magnetic flowmeter. Select the maximum output signal using the calibrator range switch.

Size: 1/8″-120″
Accuracy: ¡À0.5%
Structure: compact, remote
Velocity: 0.1~15 m/s
Power supply: 85~250 VAC, 20V~36VDC, 3.6V lithium battery
Sensor material: carbon steel (std), SS304 / SS316 (optional)
Measuring tube: SS304

Electromagnetic flowmeter consists of sensors and converters in two parts. The product is based on Faraday’s law of electromagnetic induction, used to measure the conductance greater than 20 μS / cm volume of conductive liquid flow
Medium temperature:
Integral type : -20℃~60℃
Remote type(Rubber&Polyurethane liner): -10℃~80℃
Remote type (PTFE&PFA&F46 liner): -10℃~160℃
♦ Integrated verification,diagnostic function and empty pipe detection.
♦ Measure forward and reverse direction flows.
♦ Built-in reference electrodes,no need to connect ground ring

magnetic flow meters are calibrated on ¡À0.2% accuracy test bench, electromagnetic flowmeter is calibrationed 5 points. our calibration lab has been approved CNAS ISO/IEC 17025:2017. magmeter is calibrated by MT methoud water flow standard calibration device, mass method, comparison method and pulse method can be used, standard accuracy is ¡À0.5%, ¡À0.2% accuracy is optional.

Structure: compact, remote
Output Signal: 4~20 mA, Pulse
Communication: RS485, HART, PROFIBUS
Velocity: 0.1~15 m/s
Power supply: 85~250 VAC, 20V~36VDC, 3.6V lithium battery

Liner of electromagnetic flow meter is rubber, PTFE, PFA, FEP, etc. it can be used to measure drinking water. mag flowmeter has function of high and low alarm, empty alarm, excitation alarm, etc. Electromagnetic (mag) flow meters are volumetric flow meters that do not have any moving parts to wear down.

Size: 1/8″-120″
Accuracy: ¡À0.5%
Structure: compact, remote
Output Signal: 4~20 mA, Pulse
Communication: RS485, HART, PROFIBUS
Velocity: 0.1~15 m/s

electromagnetic flow meter can be solar-powered, solar panel iscustomized according to client requirement from 1~15 days. Transmitter of electromagnetic flow meter is installed in the cabinet to protect rain and sun. water flow meter is widely used because less obstruction, cost-effective and accurate measurement. Magnetic flowmeter don’t have any moving parts to wear down, reducing the need for maintenance or replacement.

Repeatability: 0.17%
Electrode: SUS316L, Hastelloy B, Hastelloy C
Structure: compact, remote
Liner: PTFE, PFA, Polyurethane, Neoprene, Hard Rubber, Ceramic
Output Signal: 4~20 mA, Pulse

Q&T Instrument has different equipment, like CNC, high and low temperature test for transmitters, pressure test for sensorns. QTLD electromagnetic flowmeter is 1/2″~120″, flange can be DIN, ANSI, JIS or othters. magnetic flowmeter is widely used in Sewage Treatment Plant Water Supply project and Steel & Aluminum Industries, Chemical & Fertilizer Industries. Q&T brand electromagnetic water meter has been approved ATEX explosion proof certificate. which can be used any conductivity is higher than 20 ¦ÌS/cm.

Output Signal: 4~20 mA, Pulse
Communication: RS485, HART, PROFIBUS
Power supply: 85~250 VAC, 20V~36VDC, 3.6V lithium battery
Size: DN3-DN3000
Sensor material: carbon steel (std), SS304 / SS316 (optional)
Measuring tube: SS304

magnetic flowmeter is composed by transmitter and sensor. standard configuration is carbon steel sensor, SS316L electrodes and PTFE liner. A magnetic flowmeter 41 calibrator simulates the signal provided by the electrodes in the flow tube. Liquid flow meter is widely used in Sewage Treatment Plant Water Supply project and Steel & Aluminum Industries, Chemical & Fertilizer Industries.

Output Signal: 4~20 mA, Pulse
Communication: RS485, HART, PROFIBUS
Power supply: 85~250 VAC, 20V~36VDC, 3.6V lithium battery
Size: DN3-DN3000
Sensor material: carbon steel (std), SS304 / SS316 (optional)
Measuring tube: SS304

ectromagnetic water meter is packed by wooden case or carbone box with foam to protect flow metes won’t be damaged in transit, we will rich stock, flowmeters will be delivered in 6 days. magnetic flowmeter is compsed by transmitter and sensor. The magmeter flow meter is to measure sulphuric acid, it’s configured PTFE liner and Tantalum electrodes to be anti-corrosive.

Size: 1/8″-120″
Accuracy: ¡À0.5%
Repeatability: 0.17%
Electrode: SUS316L, Hastelloy B, Hastelloy C
Structure: compact, remote

electromagnetic flowmeter can be submerged in the water or buried underground, standard cable length is 10m, 5 points are calibrated. We offer flowmeters with a range of liners, electrodes, and sizes, which can meet various conductive liquids.

Liner: PTFE, PFA, Polyurethane, Neoprene, Hard Rubber, Ceramic
Output Signal: 4~20 mA, Pulse
Communication: RS485, HART, PROFIBUS
Protection Grade: IP65 std, IP68 optional for remote
Velocity: 0.1~15 m/s

Pulse width of electromagnetic flow meter can be customized, standard cable is 10m, max length is 120m, electromagnetic flow meter is mainly used to measure beverage. liner can be PTFE or rubber, our magnetic flow meter have been approved CE-LVD, CE-EMC, ATEX, NSF, tec. it can mag flowmeter is calibrationed 5 points.

Repeatability: 0.17%
Electrode: SUS316L, Hastelloy B, Hastelloy C
Structure: compact, remote
Liner: PTFE, PFA, Polyurethane, Neoprene, Hard Rubber, Ceramic
Output Signal: 4~20 mA, Pulse

Measurement of liquid flow meter is independent of fluid density, viscosity, temperature, pressure, and conductivity. all magmeter will be tested by pressure equipment. QTLD waste water flow meter is calibrated by ISO/IEC 17025:2016 CNAS Approved Test Bench.

Size: 1/8″-120″
Structure: compact, remote
Liner: PTFE, PFA, Polyurethane, Neoprene, Hard Rubber, Ceramic
Power supply: 85~250 VAC, 20V~36VDC, 3.6V lithium battery
Size: DN3-DN3000
Measuring tube: SS304

QTLD Series magnetic flowmeter Dual frequency excitation and stable zero point.
♦ Precision coil winding technology,makes magnetic field more uniform.
♦ High protection grade,IP65,IP68
♦ No moving parts,no pressure loss.
♦ High accuracy: ±0.5% of reading,±0.3% and ±0.2% optional,velocity >0.3 m/s.

mag flow meter is mainly used to measure conductive liquids, mag flowmeter has compact and remote structurer. protection grade of remote type flow sensor is IP68, liquid flow meter can be submerged in the water. inline magnetic flow meter is calibrated on ¡À0.2% calibration device, so accuracy of electromagnetic flowmeter can be up to ¡À0.2%. the magnetic flow meter is configured 4~20 mA, pulse and RS485 modbus

Accuracy: ¡À0.5%
Structure: compact, remote
Output Signal: 4~20 mA, Pulse
Communication: RS485, HART, PROFIBUS
Protection Grade: IP65 std, IP68 optional for remote
Velocity: 0.1~15 m/s

magnetic water meter is packed by wooden case or carbone box with foam to protect flow metes won’t be damaged in transit, magnetic flowmeter can be delivered within 6 days for DN12-DN300, electromagnetic water meter is widely used because less obstruction, cost-effective and accurate measurement. Magnetic flowmeter don’t have any moving parts to wear down, reducing the need for maintenance or replacement.

Structure: compact, remote
Liner: PTFE, PFA, Polyurethane, Neoprene, Hard Rubber, Ceramic
Output Signal: 4~20 mA, Pulse
Communication: RS485, HART, PROFIBUS
Protection Grade: IP65 std, IP68 optional for remote

Signal out inline mag flowmeter is 4~20 mA, Pulse, RS485 Modbus RTU standard. GPRS, HART, Profibus DP or PA are optional. That is, the external ultrasonic flowmeter is clamped on the pipe of the measured flowmeter. By comparing the cumulative flow error of the two flowmeters.

Size: DN3-DN3000
Structure: compact, remote
Liner: PTFE, PFA, Polyurethane, Neoprene, Hard Rubber, Ceramic
Protection Grade: IP65 std, IP68 optional for remote
Power supply: 85~250 VAC, 20V~36VDC, 3.6V lithium battery
Sensor material: carbon steel (std), SS304 / SS316 (optional)

Protection grade of magnetic flow meter is IP68 for remote and IP65 for compact magnetic flow meter, sensor can be submerged in the water for 3m depth or buried underground, standard cable length is 10m, max cable length is 100m, Remote type magnetic flow meter is recommended for large size. Q&T Instrument have large stock for varous flow meters and level meters, goods can be delivered with in 4 days for regular types.

Output Signal: 4~20 mA, Pulse
Communication: RS485, HART, PROFIBUS
Protection Grade: IP65 std, IP68 optional for remote
Velocity: 0.1~15 m/s
Conductivity: > 5 ¦ÌS/cm, demineralized water > 20 ¦ÌS/cm

Liner of compact magnetic flow meter is SS316L standard, HC, Ti, Tan and PT-IR are optional, mag flow meter is mainly used to measure conductive liquid, liquid flow meter has compact and remote structurer. magmeter can add pt1000 temeprature sensor to be magnetic btu meter to monitor flow and btu of hot water and cold water, can calibrated on liquid test bench, standard accuracy is ¡À0.5%

Conductivity: > 5 ¦ÌS/cm, demineralized water > 20 ¦ÌS/cm
Size: DN3-DN3000
Sensor material: carbon steel (std), SS304 / SS316 (optional)
Measuring tube: SS304
Function: High and low alarm, exciting alarm, empty pipe alarm, self-diagnosis

Q&T Instrument is OEM with 17 year manufacturing experience. color and logo can be customized. electromagnetic flowmeter can be configuared SD card and bluetooth. standard display is LCD display, OLED display is optional. products cover magnetic flow meter, vortex, turbine flow meter, ultrasonic flow meter, etc.

Size: 1/8″-120″
Structure: compact, remote
Liner: PTFE, PFA, Polyurethane, Neoprene, Hard Rubber, Ceramic
Power supply: 85~250 VAC, 20V~36VDC, 3.6V lithium battery
Sensor material: carbon steel (std), SS304 / SS316 (optional)
Measuring tube: SS304

Measure forward and reverse direction flows.
♦ Built-in reference electrodes,no need to connect ground ring.
♦ Dual frequency excitation and stable zero point.
♦ Precision coil winding technology,makes magnetic field more uniform.
♦ High protection grade,IP65,IP68
♦ No moving parts,no pressure loss.
♦ High accuracy: ±0.5% of reading,±0.3% and ±0.2% optional,velocity >0.3 m/s

Magnetic energy meter is composed by convertor, sensor and PT1000 temperature sensor, electromagnetic btu meter monitor flow and energy of hot water and cold water, standard configuration of flange and sensor shell is carbon steel, SS304 and SS316L are optional. the electromagnetic BTU meter has wide range of nominal diameters (DN3-3000), Independent of pressure, temperature, density and viscosity, magnetic energy meter is built-in grounding electrodes

Accuracy: ¡À0.5%
Repeatability: 0.17%
Electrode: SUS316L, Hastelloy B, Hastelloy C
Structure: compact, remote
Liner: PTFE, PFA, Polyurethane, Neoprene, Hard Rubber, Ceramic

Standard liner confirguration of liquid flow meter is PTFE, it has been approved NSF and FDA with food grade, Q&T Instrument has ISO/IEC 17025 2016 CNAS Approved Test Bench for ¡À0.2% Accuracy. QTLD mag flowmeter will be tested in high and low cabinet, temperature is : -20¡æ ~ 60¡æ for 24 hours. We have 17 years manufacturing expericen, can meet variouls requirement on flow measurement.

Size: 1/8″-120″
Structure: compact, remote
Liner: PTFE, PFA, Polyurethane, Neoprene, Hard Rubber, Ceramic
Power supply: 85~250 VAC, 20V~36VDC, 3.6V lithium battery
Size: DN3-DN3000
Measuring tube: SS304

Q&T calibration equipment for electromagnetic flow meters is DN3-DN3000, standard accuracy is 0.5%, 0.2% is optional. Calibration method of electromagnetic flow meter: non-contact measurement method. Various types of instruments are usually used for data monitoring in industrial production, and mag flowmeter is one of the common instruments.

Structure: compact, remote
Liner: PTFE, PFA, Polyurethane, Neoprene, Hard Rubber, Ceramic
Protection Grade: IP65 std, IP68 optional for remote
Size: DN3-DN3000
Sensor material: carbon steel (std), SS304 / SS316 (optional)
Measuring tube: SS304

Protection grade of waste water flow meter is IP65, IP67 is optional, power can be 8~36VDC, 85~265VAC. 4~20 mA, pulse or RS485 are standard configuration. Pressure of QTLD water flow emter can be ANSI 150#, 300#, 600#, 900#, etc. Two measuring points inside the meter with no moving, parts to eliminate pressure drop
Capable of measuring electric conductive liquid and
fluids with low solid contents

Structure: compact, remote
Output Signal: 4~20 mA, Pulse
Communication: RS485, HART, PROFIBUS
Velocity: 0.1~15 m/s
Power supply: 85~250 VAC, 20V~36VDC, 3.6V lithium battery

electromagnetic flow meter can be configured yellow or green OLED display, SD card or GPRS to monitor history record, bluetooth is convenient to check flow. Magnetic flow meter can be solar-powered, solar panel can be customized according to client requirement from 1 to 15 days. Transmitter of liquid flow meter is installed in the cabinet to protect rain and sun.

Accuracy: ¡À0.5%
Repeatability: 0.17%
Electrode: SUS316L, Hastelloy B, Hastelloy C
Structure: compact, remote
Liner: PTFE, PFA, Polyurethane, Neoprene, Hard Rubber, Ceramic

waste water flow meter can be compact type and remote type, standard cable length is 10m and max cable length is 120m. electromagnetic flowmeter can be submerged in the water. magnetic flow meter is calibration equipment 5 points flow meter, mass method, comparison method and pulse method can be used.

Size: 1/8″-120″
Structure: compact, remote
Liner: PTFE, PFA, Polyurethane, Neoprene, Hard Rubber, Ceramic
Power supply: 85~250 VAC, 20V~36VDC, 3.6V lithium battery
Sensor material: carbon steel (std), SS304 / SS316 (optional)
Measuring tube: SS304

Stainless still electromagnetic flow meter is mainly used to measure beverage. liner can be PTFE or rubber, Q&T Instrument has large stock fro varous flanges for different flow meters, like magnetic fflow meter, turbine flow meter, thermal mass flow meter, etc.

Power supply: 85~250 VAC, 20V~36VDC, 3.6V lithium battery
Size: DN3-DN3000
Sensor material: carbon steel (std), SS304 / SS316 (optional)
Flange: ANSI, DIN, JIS, etc.
Measuring tube: SS304
Function: High and low alarm, exciting alarm, empty pipe alarm, self-diagnosis

Q&T have 8 sets calibration device for liquids magnetic flowmeter and 5 sets calibration equipments for gas. our calibration lab has been approved CNAS ISO/IEC 17025:2017. we use mass method, pulse or comparison method to calibrate, each electromagnetic flowmeter have calibration certificate together with goods. 5 points are calibrated for magnetic flowmeter.

Accuracy: ¡À0.5%
Structure: compact, remote
Output Signal: 4~20 mA, Pulse
Communication: RS485, HART, PROFIBUS
Protection Grade: IP65 std, IP68 optional for remote
Velocity: 0.1~15 m/s

liner of sanitary magnetic flow meter is PFA, which is approved NSF, tri-clamp standard is 3A, DIN 11851 is optional. tri-clamp electromagnetic flow meter is designed for sanitary applications, size is DN15-DN200, the sensor is SS304 or SS316 and lined with PFA. With tri-clamp, the magmeter can be installed and torn down easilyto clear, it meet the strict requirements of food-processing and pharmaceutical industries.

Size: DN3-DN3000
Accuracy: ¡À0.5%
Electrode: SUS316L, Hastelloy B, Hastelloy C
Structure: compact, remote
Output Signal: 4~20 mA, Pulse
Communication: RS485, HART, PROFIBUS

JIS 10K flange standard magneti flow meter measuring the general volume of conductive liquid flow, but also can be used to measure strong acid, alkali and other strong corrosive liquids and mud, pulp, pulp and other liquid-solid two-phase suspension of uniform volume flow.
Frequency Output : 1~5000 Hz
● Language : English,Chinese
Other languages are available
● Flange Standard : EN1092-1
PN10,PN16,PN25,PN40
ANSI BS16.5 Class 150,300,600
JIS2220 10K,20K,40
AS2129 Table D,Table E
AS4087 PN16,PN21,PN35
● Exciting Current : 125mA, 187mA, 250mA
● Exciting Frequency : 3.12Hz, 4.16Hz, 6.25Hz
12.5Hz, 25Hz, 30Hz
● Material
Measuring Tube : Stainless Steel 304
Flange : Carbon Steel (standard)
: Stainless Steel 304 (optional)
: Stainless Steel 316 (optional)