High quality 1.0% grade thermal gas flow meter

Theemal flowmeters directly indicate the mass flow or normalized volume flow of gases without any additional pressure and temperature compensation. They have an impressively high accuracy, short response time and a very wide flow range with virtually no loss of accuracy even at the lowest flow rates.
Widely turndown ratio:100:1
Power supply:24VDC&220VAC
Response time:1S

Thermal gas mass flowmeter’s medium temperature range of meter is -40¡æ¡«220¡æ.
When the gas is very humid or saturated with water (e. g. Bio Gas), the piping and flowmeter body should be insulated to prevent water droplets condensing on the measuring sensor.
Insertion type:DN32~DN4000
Flange type:DN10~DN300
Tri-clamp type :DN10~DN100
Thread type:DN10~DN100

For the insertion type instrument, on the premise that both the measuring media and field environment are applicable for online dismantlement with non-stop operation, it is viable to have maintenance operation with non-stop operation relying on its special structure
Media:All gas except acetylene and humid gas
Measure range:1:100
Sesnsor working temperature:-20~220℃
Transmitter working temperature:-20~45℃
Output:4-20mA

Natural gas thermal mass flow meters measure the mass flowrate of fluids by measuring the heat conducted from a heated surface to the flowing fluid. Since a flowing fluid removes a known quantity of heat as it passes, the temperature difference between the heated sensor and the flow stream is directly proportional to the mass flow rate.
With RS485 or HART communication
Power supply:24VDC ,220VAC
Accuracy:¡À1.0%~¡À1.5%

Q&T thermal gas mass flow meter with DC4-20mA four-wire output,which is more convenient for remote reception.Support MODBUS RTU RS485 protocol,coordinating the receiving system to collect more data ans modify system
Velocity:0.1~100Nm/s
Media temperature:-40~+220¡æ
Size£º
Insertion type:DN32~DN4000
Flange type:DN10~DN300
Tri-clamp type :DN10~DN100
Thread type:DN10~DN100

Insertion type thermal gas mass flow meter need to reserve 20mm mounting hole,which could be used to weld and fix the base,Inline type thermal gas mass flow meter could be min.size 10mm.
Easy installation and maintenance. If the conditions on site are permissible, the meter can achieve a hot-tapped installation and maintenance. (Special order of custom-made)
Output:4-20mA,Pulse,OCT
Communication:RS485
Transmitter working temperature:-10~70¡æ
Sensor wotking temperature:-30~150¡æ
Power supply:DC24V,AC220V

Thermal gas mas flow meters are measuring the mass flow or volume flow of gas,flow range can do 0.5Nm/s¡«100Nm/s. So this meter also can be used for gas leak detection.
Thermal flow sensor temp is always 30¡æ higher than the medium temperature (environment temperature), and the meter adopts method of constant differential temperature, therefore the meter don¡¯t need temperature and pressure compensation in principle.
Accuracy:
In-line type accuracy:¡À1.0%
Insertion type accuracy::¡À1.5%
Power supply:DC24V and AC220V
Output:4-20mA,Pulse,RS485
Body material:Standard SS304,and SS316 is optional
Velocity:0.1~100Nm/s
Media temperature:-40~+220¡æ

Thermal gas mass flow meter is one kind of precision instrument,ensuring the accuracy is important.
Q&T adopt the critical flow nozzle calibration device to calibrate each gas mass flow meter,the calibration device flow range can reach Min. 0.5m3/h and Max.10000 m3/h .
Media:All gas except acetylene and humid gas
Measure range:1:100
Sesnsor working temperature:-20~220℃
Transmitter working temperature:-20~45℃
Output:4-20mA
Accuracy:±1.0%~±2.5%
Probe material:SS316L
Power supply:24VDC ,220VAC
Response time:1S
Display:4 line digital

Pulse output thermal gas mass flowmeters is one kind of instrument that measures the gas mass flowrate.
Thermal gas flow meter can be divided into inline type and isert type according to the instructure.
With RS485 or HART communication

Thermal flow meter measure gas mass flow in various processes and offer distinct advantages, such as repeatability, low maintenance, and operating over a wide flow range. Here we discuss the meter¡¯s fundamentals, the working principle of thermal mass flow measurement, and the two approaches to measuring heat dissipation.
In-line type accuracy:¡À1.0%
Insertion type accuracy::¡À1.5%
Power supply:DC24V and AC220V
Output:4-20mA,Pulse,RS485

According the installation,thermal gas mass flow meter is divide into insertion type and inline type.
Whatever insertion or inline gas mass flow meter,they all have no moving parts and measure the mass of the fluid directly.This make thermal gas mass flow meter measure the standardized volumetric flow rates and totals without the need for temperature or pressure compensation
Velocity:0.1~100Nm/s
Output:4-20mA,Pulse,RS485
Body material:SS304
Alarm output:1-2 relay
Pressure up to 4.0Mpa

The thermal gas flowmeter is mainly used for measuring gas with low flow and the range could reach 1:100,which is btter than gas flowmeter on market and low flow could be measured,the min.flow velocity can reach 0.1Nm/s and Max. velocity reach 100Nm/s
Media:All gas except acetylene and humid gas
Measure range:1:100
Sesnsor working temperature:-20~220℃
Transmitter working temperature:-20~45℃
Output:4-20mA

Thermal flowmeters directly indicate the mass flow or normalized volume flow of gases without any additional pressure and temperature compensation. They have an impressively high accuracy, short response time and a very wide flow range with virtually no loss of accuracy even at the lowest flow rates
Mass flow
SS304 rod
Dual power:24VDC,220VAC
Min.Flow velocity:0.1Nm/s
Online installation

Air thermal gas mass flow meter is very intelligent gas flow meter and can display Nm3 and Kg unit at same time.
And thermal gas mass flow meter be adopted dual power supply,user can easy to choose the poer spurce.
Thermal flow meter measure gas mass flow in various processes and offer distinct advantages, such as repeatability, low maintenance, and operating over a wide flow range. Here we discuss the meter¡¯s fundamentals, the working principle of thermal mass flow measurement, and the two approaches to measuring heat dissipation.

Compressed air thermal gas mass flow meter is very intelligent gas flow meter and can display Nm3 and Kg unit at same time.
And thermal gas mass flow meter be adopted dual power supply,user can easy to choose the poer spurce.
Thermal flow meter measure gas mass flow in various processes and offer distinct advantages, such as repeatability, low maintenance, and operating over a wide flow range. Here we discuss the meter¡¯s fundamentals, the working principle of thermal mass flow measurement, and the two approaches to measuring heat dissipation.

Thermal gas mass flow emter be widely used in the process control and gas flow measurement of petroleum, chemical industry, metallurgy, electric power, water treatment, papermaking, food, medicine, cement, textile and various production and scientific research institutions.
Natural gas thermal gas mass flow meter can reach 1.0% accuracy and has been calibrated by a third-party laboratory.
Dual power:24VDC,220VAC
Min.Flow velocity:0.1Nm/s
Online installation

Thermal gas flowmeter is mainly used for measuring gas with low flow and the range could reach 1:100,which is btter than gas flowmeter on market and low flow could be measured,the min.flow velocity can reach 0.1Nm/s and Max. velocity reach 100Nm/s
Volume flow /Mass flow
Pressure:
Insertion type¡Ü1.6Mpa
Flange type ¡Ü4.0Mpa
Accuracy:
In-line type accuracy:¡À1.0%
Insertion type accuracy::¡À1.5%
Power supply:DC24V and AC220V

Thermal gas mas flow meters are measuring the mass flow or volume flow of gas,flow range can do 0.5Nm/s¡«100Nm/s. So this meter also can be used for gas leak detection.
Thermal flow sensor temp is always 30¡æ higher than the medium temperature (environment temperature), and the meter adopts method of constant differential temperature, therefore the meter don¡¯t need temperature and pressure compensation in principle.

Q&T gas mass thermal flow meters are be calibrated by gas venturi sonic nozzle calibration device,and ensure the thermal gas mass flowmeter accuracy can reach 1.0% and 1.5%.
When calibrate thermal flow meter,Q&T will choose four flow velocity points ,then calibrate 3 times each velocity point
Media:All gas except acetylene and humid gas
Measure range:1:100
Sesnsor working temperature:-20~220℃
Transmitter working temperature:-20~45℃
Output:4-20mA

Thermal gas mass flowmeters directly indicate the mass flow or normalized volume flow of gases without any additional pressure and temperature compensation. They have an impressively high accuracy, short response time and a very wide flow range with virtually no loss of accuracy even at the lowest flow rates and the range could reach 1:100.
Volume flow /Mass flow
SUS304 body
MODBUS RTU RS485
0.1~100Nm/s
4 lines LCD
EX-PROOF

Thermal gas mass flow meter sensor is adopted reinforcing design and the root is partially reinforced to make the probe stronger and more suitable for a variety of media
Thermal mass flow meter is precision instruments that can directly measure mass flow,such as industrial gases, compressed gas, and other gases.
DC4-20mA four-wire output
Mass flow unit
Dual power:24VDC,220VAC
Min.Flow veloctiy:0.1Nm/s
Output:4-20mA

Except insert type,Q&T also can manufacture Flange thermal flow meter,Thread thermal flow meter ,Wafer type thermal flow meter,Tri-clamp type thermal flow meter .
Q&T also can do OEM for clients,such as Display,Color,Output etc.
Insertion type:DN32~DN4000
Flange type:DN10~DN300
Tri-clamp type :DN10~DN100
Thread type:DN10~DN100

4-20mA ouput thermal gas mass flow meter is on kind flow meter for direct mass measurementt of Air,N2, CO2,Natrual gas ect.
Whenever low pressure loss is important in gas industry thermal mass flowmeters offer a real alternative to traditional measuring techniques.
Whatever for process control, consumption and supply monitoring, detecting leaks or monitoring distribution networks. Using insertion versions, it is also possible to measure gas flows in very large pipelines or in rectangular ducts.
Media:All gas except acetylene and humid gas
Measure range:1:100
Sesnsor working temperature:-20~220℃
Transmitter working temperature:-20~45℃
Output:4-20mA
Accuracy:±1.0%~±2.5%
Probe material:SS316L
Power supply:24VDC ,220VAC
Response time:1S
Display:4 line digital

Thermal gas mass flowmeters are suitable for all industrial and test rig applications that demand quick and precise gas measurement. The flowmeters directly indicate the mass flow or normalized volume flow of gases without any additional pressure and temperature compensation. They have an impressively high accuracy, short response time and a very wide flow range with virtually no loss of accuracy even at the lowest flow rates.
Mass flow
SS304 rod
Dual power:24VDC,220VAC
Min.Flow velocity:0.1Nm/s
Online installation

As the important gas flow meter,thermal gas flow meter is very popluar to measure various of dry gas.
This gas mass flow meters are be calibrated by sonic nozzle,current the snoic nozzle is more better clibration device for gas flow meter,and ensure the accuracy during calibrating
Pressure up to 4.0Mpa
Dural power:24VDC,220VAC
4-20mA is Optical isolation
Power supply:DC24V and AC220V
Output:4-20mA,Pulse,RS485
Body material:Standard SS304,and SS316 is optional

Q&T adopt the critical flow nozzle calibration device to calibrate each gas mass flow meter,the calibration device flow range can reach Min. 0.5m3/h and Max.10000 m3/h .
Nozzle calibration device more ensure the flow meters’ accuracy
Accuracy:
In-line type accuracy:¡À1.0%
Insertion type accuracy::¡À1.5%
Power supply:DC24V and AC220V

Q&T thermal gas mass flow meter with DC4-20mA four-wire output,which is more convenient for remote reception.Support MODBUS RTU RS485 protocol,coordinating the receiving system to collect more data ans modify system
Insertion rod diameter :
DN32~DN50 standard rod dia. 12mm ,14mm is optional
DN65~DN4000 standard rod dia.19mm,12mm and 14mm is optional

Thermal dry gas flow meter is mainly used in air and gas flow measurement. The meters have flange type,wafer type,thread type,tri-clamp type;
Thermal gas mass flow meter consist of a transmitter and probe with temperature sensors (RTDS) located in the pins at the bottom of the probe. One sensor measures the process temperature and the other sensor is heated to a specific temperature above this. As the flow rate increases, heat gets taken away from the heated sensor in the form of convective heat transfer.
Media temperature:-40~+220¡æ

Size£º
Insertion type:DN32~DN4000
Flange type:DN10~DN300
Tri-clamp type :DN10~DN100
Thread type:DN10~DN100

Accuracy:
In-line type accuracy:¡À1.0%
Insertion type accuracy::¡À1.5%

Thermal gas mass flow meter is one kind of precision instrument,ensuring the accuracy is important.
Q&T adopt the critical flow nozzle calibration device to calibrate each gas mass flow meter,the calibration device flow range can reach Min. 0.5m3/h and Max.10000 m3/h .
Nozzle calibration device more ensure the flow meters’ accuracy
Accuracy:
In-line type accuracy:¡À1.0%
Insertion type accuracy::¡À1.5%
Power supply:DC24V and AC220V
Output:4-20mA,Pulse,RS485
Body material:Standard SS304,and SS316 is optional

Thermal gas mass flow meter for pipe dia. DN10~DN2000 and is precision instrument that directly measure gas.
Themal mass flow meter have widely turndown ratio 1:100,so this flow meter is advantage for low flowrate and can be used to detect leak.
Media:All gas except acetylene and humid gas
Measure range:1:100
Sesnsor working temperature:-20~220℃
Transmitter working temperature:-20~45℃
Output:4-20mA