High accuracy inline ultrasonic flow meter for water

Ultrasonic Flow meter handheld clamp on flowmeter no pipe cutting required. The user simply clamp on the flow sensor to the pipe surface. Ultrasonic Flow meter handheld clamp on flowmeter can then detect the flow through ultrasonic waves, and then automatically calculate the flow rate value, flow accumulator, etc. No pipe cutting means no damage to the pipe. So as long as the pipes are in good condition, the installation on the flowmeter will not provide the possibility of leakage. Sensor: Clamp-on/External Principle: transmit time Size: DN15mm-DN6000mm Measuring medium: Liquid 3.6V Battery-powered

Our open channel flow meter display the level, flow rate, accumulate flow at the same time; This ultrasonic water flow meter has Analogue Output: 4-20mA, corresponding to instantaneous flow.
Display: Backlight LCD
The maximum of Accumulative Flow: 9999999.9 m3/h
Accuracy of Change in Level: 1mm or 0.2% of full span (whichever is greater)
Resolution: 1mm
Analogue Output: 4-20mA, corresponding to instantaneous flow
Relays Output: Standard 2 relay outputs(Optional up to 6 relays)
Serial Communication: RS485, MODBUS -RTU standard protocol
Ambient Temperature: -40 ~70 Degree C
Power Supply: DC24V (+5%) 0.2A; AC220V (+20%) 0.1A ;Optional DC12V

4-20mA pulse RS485 wall mounted ultrasonic flow meter is a high precision no-cut tube measurement method. This special design includes matching sensors for ease of use and is ideal for installation in existing systems Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring single clean liquids Power supply: 24VDC/85VAC-2265AC Storage: SD card optional Heat meter optional

RS232 Signal Handheld ultrasonic flow meter Clamp on tranducer is a portable liquid flow measurement device with a sensor. RS232 Signal Handheld ultrasonic flow meter Clamp on tranducer adopt transit-time ultrasonic measurement technology for superior accuracy and ease of installation and installation. This easy-to-use flowmeter comes in a rugged, waterproof carrying case for easy transport of the display, sensor, and cables between measurement locations. High accuracy +/-1.0% of FS Transducer temperature: -30~90¡ãC/-30¡ãC~160¡ãC Measuring clean liquids Battery-powered,for 12 hours Communication: RS232

ultrasonic water flow meters RS485 digital water flow meter clamp on ultrasonic portable liquid flow meter is controlled by a micro-processor system which contains a wide range of data that enables it to be used with pipes with an outside diameter ranging from 15mm up to 1200mm (depending on model) and constructed of almost any material. instrument will also operate over a wide range of fluid temperatures

Ultrasonic flow measurement according to the ¡°differential transit time¡± method: This method uses two sensors, set opposite each other in the measuring tube. Each sensor can alternately transmit and receive ultrasonic signals, while simultaneously measuring the signal transit time.
Bi-directional flow measurement
Backlit LCD
Measuring up to 100 times/s
Accuracy:¡À0.5%

The ultrasonic open channel flowmeter has 4-20mA and RS485 signal output, it can be equipped with a communication interface, which is easy to connect with SCADA systems to achieve industrial remote monitoring and control. This Open Channel flow meter measures level, flow rate and total volume of water flowing through weirs, flumes, and channels etc.

Specifications:
Sensor?Level?Range: 0-4.0m; other?level?range?also?available
Blind?zone: 0.20m
Temperature?Compensation: Integral?in?probe
Pressure?Rating: 0.2MPa
Beam?Angle: 8*?(3db)
Cable?Length: 10m?standard?(can?be?extended?to?1000m)
Sensor?Material: ABS,?PVC?or?PTFE?(optional)
Sensor?Protection Class: IP68

China Supplier LCD Displayer Digital Water Flow Meter and Ultrasonic Flow Meter Price is a portable liquid flow measurement device with a sensor. Hot sales portable ultrasonic flowmeter handheld water flow meter adopt transit-time ultrasonic measurement technology for superior accuracy and ease of installation and installation. This easy-to-use flowmeter comes in a rugged, waterproof carrying case for easy transport of the display, sensor, and cables between measurement locations. High accuracy +/-1.0% of FS Transducer temperature: -30~90¡ãC/-30¡ãC~160¡ãC Measuring clean liquids Battery-powered,for 12 hours Communication: RS232

Multi-channel ultrasonic flow meter is suitable for continuously measuring flow and heat of clean and uniform liquids without large concentration particles or gases under industrial environment.
Ultrasonic flow meter can measure water,Seawater,Acid solution,Cooking oil,Gasoline,Coal oil,Diesel,Alcohol,
Beer and other uniform liquid could transmitting ultrasonic waves.

QT811 clamp on type ultrasonic BTU flow meter with clamp-on transducers create no wear, zero pressure loss,
and do not require process interruptions to install them since they are attached to the outside of the pipe. Clamp on BTU energy flow meter adopts a new external clamp design, which could get the flow rate without touch the measurement medium.

Pipe Size:?DN15-DN40mm (1/2¡±~1 1/2¡±)
Flow Range:¡À0.1m/s ~¡À5m/s
Temperature: 0~75¡æ (standard)
Output: 4-20mA, OCT Pulse, RS485
Accuracy:?¡À1% of measured value
Power Supply: DC10-24V

QTDS-100F wall mounted ultrasonic water flowmeter seawater flow meter adopts the self-development measurement technology.This measurement technique is a faster and more accurate process time measurement algorithm. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring single clean liquids Power supply: 24VDC/85VAC-2265AC Communication: RS485

Handheld Ultrasonic Flowmeter Clamp on Flow Meter Portable Liquid Flow Meter with small transducer to measure flow rate through the pipe wall, the transit time ultrasonic flow principle. It is a 3.6V battery powered ultrsonic flow meter, for using on a wide range of sizes and can provide 24 hours measurement continuely. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring clean liquids Built-in rechargeable battery 3.6V 2000 lines storage Communication: RS232

The fluid can smothly through the inline ultrasonic flow sensors which no moving pasts,No wear,No pressure loss and Maintenance free.
Pipeline ultraosnic flow meter directly contact the liquid and make the measuring accuracy better than clamp on ultrasonic flowmeter.And installation easy,don’t need calculate the sensor installation distance and cover the coupling agent in the pipe,so this meter can collect the signal very well.
Power supply:DC24V and AC220V
Connection way:Flange type
Media temperature :-30~+150¡æ

QT621 portable type ultrasonic flow meter is a type of portable instrument for non-invasive, quick flow and energy measurement with clamp-on technology for many types of piping.
Portable ultrasonic flow meter mainly consists of two parts, main display part and transducer part. With 4-20mA and RS485 communication available, QT621 portable ultrasonic flow meter support quickly verify the flow reading of another meter and to data log flow system values over an extended time period.

Size: 1¡å~48¡å(25mm~1200mm)
Flow Range:¡À0.01 m/s~ ¡À12 m/s
Accuracy: ¡À1%
Repeatability: 0.2%
Output: 4-20mA, RS485
Power supply: Internal lithium 3000mAh
Transducer: IP68

Flange ultrasonic flow meter could be manufactured from 50mm~700mm and mainly be used to measure the flow and heat of clean liquid which don’t contain large concentration of suspended particles or gas.

The structure of Waste Water Flowmeter Handheld Ultrasonic Flow Meter is mainly divided into ultrasonic signal generator, signal receiver and information processing circuit, flow display. First, the ultrasonic signal generator is used to send the signal, the sensor receives the signal, and the time difference is obtained. The ultrasonic information is processed according to the information processing circuit, and the flow is transmitted to the display screen in the form of an electrical signal, and the result is displayed Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Medium: clean liquids,pure water Built-in rechargeable battery 3.6V Communication: RS232

0.5% accuracy ultraosnic flow meter with multi channel sensor and body mainly be adopted carbon steel material ,can produce stainless stell according to request.
Instantaneous flow,Total flow,Heat,Positive flow,Negative flow
High Isolation voltage,Strong anti-interference,Suppress voltage noise,Good isolation performance
Inline ultrasonic flow meter collect temperature signal and accuracy reach 0.001¡æ
When using inline ultrasonic flow meter to measure,allowing pipe with liner

QT621 handheld ultrasonic flow meter support accurate bidirectional and highly dynamic flow measurement
with the non-invasive clamp-on technology. Handheld type ultrasonic flow meter mainly applies for measuring the flow of homogeneous medium fluid in the water injection flow measurement, raw water flow measurement, tap water flow measurement etc.

Size: 1¡å~48¡å(25mm~1200mm)
Flow Range:¡À0.01 m/s~ ¡À12 m/s
Accuracy: ¡À1%
Repeatability: 0.2%
Output: 4-20mA, RS485
Power supply: Internal lithium 3000mAh
Transducer: IP68

QT621 battery powered ultrasonic clamp on flow meters are widely used from simple water flow
measurements to energy flow monitoring and automated process control.
Portable ultrasonic flow meters are with various kinds of output signals, including, 4-20mA analog and RS485 modbus which is very common and convenient for onsite monitoring.

Size: 1¡å~48¡å(25mm~1200mm)
Flow Range:¡À0.01 m/s~ ¡À12 m/s
Accuracy: ¡À1%
Repeatability: 0.2%
Output: 4-20mA, RS485
Power supply: Internal lithium 3000mAh
Transducer: IP68

Q&T Modbus Digital Ultrasonic Fluid Flow Meter Clamp On Ultrasonic Flowmeter provide you with an accurate, easy-to-install flow meter. wall mount flow sensor feature quick, easy clamp-on sensor installation, configuration, and a user-programmable menu-driven interface for easy commissioning in the field. Q&T Modbus Digital Ultrasonic Fluid Flow Meter Clamp On Ultrasonic Flowmeter use a special technology to ensure highly accurate flow measurement. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring single clean liquids Power supply: 24VDC/85VAC-2265AC Storage: SD card optional Heat meter optional

Q&T PLCM Open Channel flow meter is Wall mounted converter ultrasonic flow meter for sewage water Open Channel Flow Meter, The cable length between probe and host up to 1000m; This PLCM ultrasonic flow meters are perfect for wastewater applications.
The probe with leak-proof structure and IP68 protect grade.
Display: Backlight LCD
The maximum of Accumulative Flow: 9999999.9 m3/h
Accuracy of Change in Level: 1mm or 0.2% of full span (whichever is greater)
Resolution: 1mm
Analogue Output: 4-20mA, corresponding to instantaneous flow
Relays Output: Standard 2 relay outputs(Optional up to 6 relays)
Serial Communication: RS485, MODBUS -RTU standard protocol
Ambient Temperature: -40 ~70 Degree C
Power Supply: DC24V (+5%) 0.2A; AC220V (+20%) 0.1A ;Optional DC12V

QT621 ultrasonic water flow meter support is widely used in oil industry, water treatment, pure water, chemical and etc. Adopt the technology of transit time, ultrasonic waves transmitted and received through moving liquid. The difference between upstream and downstream transit time can be used to calculate flow and velocity.

Size: 1¡å~48¡å(25mm~1200mm)
Flow Range:¡À0.01 m/s~ ¡À12 m/s
Accuracy: ¡À1%
Repeatability: 0.2%
Output: 4-20mA, RS485
Power supply: Internal lithium 3000mAh
Transducer: IP68

Precise digital display insertion clamp on ultrasonic water flow meter Wall mounted ultrasonic flowmeter is an ultrasonic flowmeter used to measure the flow rate of liquids in closed pipes. The transducer is a non-contact, clamp-on type, which will provide the benefits of contamination-free operation and ease of installation. The transit time flowmeter employs two transducers, which act as ultrasonic transmitters and receivers. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring clean liquids Power supply: 24VDC/85VAC-2265AC Communication: RS485

QT621 portable ultrasonic flow meters are with features of for flexibility and performance, providing the user with a comprehensive specification and a list of configuration options. Portable type ultrasonic flow meters are widely used in all areas such as drinking water and sewerage industry, power plants, producing industry, food industry and so on.

Size: 1¡å~48¡å(25mm~1200mm)
Flow Range:¡À0.01 m/s~ ¡À12 m/s
Accuracy: ¡À1%
Repeatability: 0.2%
Output: 4-20mA, RS485
Power supply: Internal lithium 3000mAh
Transducer: IP68

The open channel flow meter level sensor is mounted on the top of the flume, and ultrasonic wave is transmitted by the probe to the surface of the monitored material. Instead of using mass or volumetric data to determine the rate of flow of a substance, open channel flow meters monitor the relationship between the depth of the liquid and the flow rate.

Specifications:
Sensor?Level?Range: 0-4.0m; other?level?range?also?available
Blind?zone: 0.20m
Temperature?Compensation: Integral?in?probe
Pressure?Rating: 0.2MPa
Beam?Angle: 8*?(3db)
Cable?Length: 10m?standard?(can?be?extended?to?1000m)
Sensor?Material: ABS,?PVC?or?PTFE?(optional)
Sensor?Protection Class: IP68

Ultrasonic Flow meter electromagnetic flow meter handheld clamp on flowmeter is simple to install and is suitable for large diameter pipes requiring monitoring and flow measurement, as well as a wide network of smaller supply lines. Ultrasonic Flow meter electromagnetic flow meter handheld clamp on flowmeter provide the tools needed to meet the diverse requirements of such a demanding industry. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring clean liquids Power supply: 24VDC/85VAC-2265AC Communication: RS485

Ultrasonic Flow meter for applications in clean water and in low conductivity media. Operating principle based on transit time measurement.
Signal channel type ultrasonic flow meter accuracy it better than 1.0%
Multi-channel type ultrasonic flow meter accuracy can reach 0.5%

Q&T PLCM Open Channel flow meter is CE Certificated Open Channel Flowmeter, RS485 River Flow Meter Open Channel; The cable length between probe and host up to 1000m; This PLCM ultrasonic flow meters are perfect for wastewater applications.
The probe with leak-proof structure and IP68 protect grade.
Display: Backlight LCD
The maximum of Accumulative Flow: 9999999.9 m3/h
Accuracy of Change in Level: 1mm or 0.2% of full span (whichever is greater)
Resolution: 1mm
Analogue Output: 4-20mA, corresponding to instantaneous flow
Relays Output: Standard 2 relay outputs(Optional up to 6 relays)
Serial Communication: RS485, MODBUS -RTU standard protocol
Ambient Temperature: -40 ~70 Degree C
Power Supply: DC24V (+5%) 0.2A; AC220V (+20%) 0.1A ;Optional DC12V

Sewage and rainwater are often transported to the treatment plant in open collection channels or flumes.This open Channel flow meter is good for this application, it can be used for continuous measuring of municipal rain-water, wastewater, sewage discharge and irrigation water pipelines.

Specifications:
Display: Backlight?LCD
Flow?Rate?Range: 0.0000~99999L/S?or?m3/h
The?maximum?of Accumulative Flow: 9999999.9?m3/h
Accuracy?of?Change in Level: 1mm?or?0.2%?of?full?span?(whichever?is?greater)
Resolution: 1mm
Analogue?Output: 4-20mA,?corresponding?to?instantaneous?flow
Relays?Output: Standard?2?relay?outputs(Optional?up?to?6?relays)
Serial?Communication: RS485,?MODBUS?-RTU?standard?protocol

This Open channel flow meter require accurate measurement of the surface level of a liquid. A flume, channel or structure which has a known characteristic flow per measured head, together with the measured liquid level, accurately define the flow rate through the system.
Applications including Wastewater collection systems,combined sewer systems and outfalls, Wastewater treatment facilities,Irrigation canals and channels, Industrial process and discharges, Stormwater conveyance and outfalls.

Specifications:
Analogue?Output: 4-20mA,?corresponding?to?instantaneous?flow
Relays?Output: Standard?2?relay?outputs(Optional?up?to?6?relays)
Serial?Communication: RS485,?MODBUS?-RTU?standard?protocol
Ambient?Temperature: -40 ~70 Degree C
Measure?Cycle: 1?second?(selectable?2?seconds?)
Power?Supply: DC24V?(+5%)?0.2A;?AC220V?(+20%)?0.1A?;Optional?DC12V