HART output stainless steel SS304 Flange vortex flowmeter

Vortex flow meter also could use for flue gases, carbon dioxide, fully demineralized water, solvents, heat-transfer oils, boiler feedwater, condensate water, etc.
Size: DN15-DN6000
Measured medium: liquid,gas,steam; Medium Temp: -40¡æ~250¡æ,-40¡æ~350¡æ,
Nominal Pressure: 1.6MPa
Accuracy: ¡À1.0 % (Flange / wafer / thread / tri-clamp, ¡À1.5 % (Insertion type)
Flow Range: Liquid:0.4-7.0m/s,Gas:4.0-60.0m/s,Steam:5.0-70.0m/s,
Material: SS304(Standard),SS316(Optional)
Vibration Acceleration Allowed: ¨Q0.2g
IEP ATEX: II 1G Ex ia IIC T5 Ga
Ambient Condition: Ambient temp: -40¡æ~65¡æ (Non-explosion-proof site), -20¡æ~55¡æ (Explosion-proof site)
Power Supply: DC 12-30V or 3.6V battery powered

Air vortex flowmeter operate under the vortex shedding principle,where an oscillating vortexes occur when a fluid flow past a bluff (as opposed to streamlined) body,also call as shedding flow meter.
Size: DN15-DN6000
Measured medium: liquid,gas,steam; Medium Temp: -40¡æ~250¡æ,-40¡æ~350¡æ,
Nominal Pressure: 1.6MPa
Accuracy: ¡À1.0 % (Flange / wafer / thread / tri-clamp, ¡À1.5 % (Insertion type)
Flow Range: Liquid:0.4-7.0m/s,Gas:4.0-60.0m/s,Steam:5.0-70.0m/s,
Material: SS304(Standard),SS316(Optional)
Vibration Acceleration Allowed: ¨Q0.2g
IEP ATEX: II 1G Ex ia IIC T5 Ga
Ambient Condition: Ambient temp: -40¡æ~65¡æ (Non-explosion-proof site), -20¡æ~55¡æ (Explosion-proof site)
Relative Humidity: ¨Q85%

Vapor vortex flowmeter use for liquid measurement,under strict calibration with liquid test bench for liquid vortex flow meter,enjoy ¡À1% accuracy in actual measurement. Flow Range: Liquid:0.4-7.0m/s,Gas:4.0-60.0m/s,Steam:5.0-70.0m/s,
Specifications: DN100-2000 (Insertion),
Material: SS304(Standard),SS316(Optional)
Vibration Acceleration Allowed: ¨Q0.2g
IEP ATEX: II 1G Ex ia IIC T5 Ga
Ambient Condition: Ambient temp: -40¡æ~65¡æ (Non-explosion-proof site), -20¡æ~55¡æ (Explosion-proof site)
Relative Humidity: ¨Q85%
Power Supply: DC 12-30V or 3.6V battery powered

Intelligent vortex flow meter with accuracy ¡À1.5%,compact vortex flow meter is workable with liquid or gas measurement, the calibration medium is different base on actual medium. Flow Range: Liquid:0.4-7.0m/s,Gas:4.0-60.0m/s,Steam:5.0-70.0m/s,
Specifications: DN100-2000 (Insertion),
Vibration Acceleration Allowed: ¨Q0.2g
IEP ATEX: II 1G Ex ia IIC T5 Ga
Relative Humidity: ¨Q85%
Pressure: 86kPa -106kPa
Signal Output: 4-20mA,Pulse Communication: RS485 MODBUS or HART

Steam flowmeter use to measure gas, steam or liquid flow,could display mass flow rate, vortex air flow meter also could work as mass flow meter in various kinds of mediums. Measured medium: liquid,gas,steam; Medium Temp: -40¡æ~250¡æ,-40¡æ~350¡æ,
Accuracy: ¡À1.0 % (Flange / wafer / thread / tri-clamp; ¡À1.5 % (Insertion type)
Flow Range: Liquid:0.4-7.0m/s,Gas:4.0-60.0m/s,Steam:5.0-70.0m/s,
Specifications: DN100-2000 (Insertion),
Material: SS304(Standard),SS316(Optional)
Vibration Acceleration Allowed: ¨Q0.2g
IEP ATEX: II 1G Ex ia IIC T5 Ga
Ambient Condition: Ambient temp: -40¡æ~65¡æ (Non-explosion-proof site), -20¡æ~55¡æ (Explosion-proof site)

Steam flowmeter is applicable for liquid or gas measurement,the calibration is different for vortex air flow meter and liquid vortex flow meter. Size: DN15-DN6000; Measured medium: liquid,gas,steam; Medium Temp: -40¡æ~250¡æ,-40¡æ~350¡æ,
Accuracy: ¡À1.0 % (Flange / wafer / thread / tri-clamp; ¡À1.5 % (Insertion type)
Specifications: DN100-2000 (Insertion),
Material: SS304(Standard),SS316(Optional) Signal Output: 4-20mA,Pulse Communication: RS485 MODBUS or HART

Each gas vortex flowmeter will under strict calibration then could guarantee better accuracy,with gas venturi nozzle realize field real flow calibration for every vortex flow meter. Size: DN15-DN6000; Measured medium: liquid,gas,steam; Medium Temp: -40¡æ~250¡æ,-40¡æ~350¡æ,
Nominal Pressure: 1.6MPa
Accuracy: ¡À1.0 % (Flange / wafer / thread / tri-clamp; ¡À1.5 % (Insertion type) Flow Range: Liquid:0.4-7.0m/s,Gas:4.0-60.0m/s,Steam:5.0-70.0m/s,
Specifications: DN100-2000 (Insertion),
Material: SS304(Standard),SS316(Optional)
Power Supply: DC 12-30V or 3.6V battery powered

Vortex shedding flowmeter is sensitive to variations in the process conditions are low and with no moving parts have relatively low wear compared to other types of flow meters.
Size: DN15-DN6000
Measured medium: liquid,gas,steam; Medium Temp: -40¡æ~250¡æ,-40¡æ~350¡æ,
Nominal Pressure: 1.6MPa
Accuracy: ¡À1.0 % (Flange / wafer / thread / tri-clamp, ¡À1.5 % (Insertion type)
Material: SS304(Standard),SS316(Optional)
Vibration Acceleration Allowed: ¨Q0.2g
IEP ATEX: II 1G Ex ia IIC T5 Ga
Ambient Condition: Ambient temp: -40¡æ~65¡æ (Non-explosion-proof site), -20¡æ~55¡æ (Explosion-proof site)
Relative Humidity: ¨Q85%
Pressure: 86kPa -106kPa

Palm oil vortex flow meter popular in all over the world in steam measure,vortex flow meter also called as steam flowmeter,flowmeter transfer data via 4-20mA,HART,RS485 etc. Size: DN15-DN6000
Measured medium: liquid,gas,steam; Medium Temp: -40¡æ~250¡æ,-40¡æ~350¡æ,
Nominal Pressure: 1.6MPa
Accuracy: ¡À1.0 % (Flange / wafer / thread / tri-clamp; ¡À1.5 % (Insertion type)
Flow Range: Liquid:0.4-7.0m/s,Gas:4.0-60.0m/s,Steam:5.0-70.0m/s,
Specifications: DN100-2000 (Insertion),
Material: SS304(Standard),SS316(Optional)
Vibration Acceleration Allowed: ¨Q0.2g

Insertion vortex flowmeter enjoy accuracy ¡À1.5%,air flow meter vortex flowmeter is workable with liquid or gas measurement,the calibration medium is different base on actual medium. Flow Range: Liquid:0.4-7.0m/s,Gas:4.0-60.0m/s,Steam:5.0-70.0m/s,
Specifications: DN100-2000 (Insertion),
Vibration Acceleration Allowed: ¨Q0.2g
IEP ATEX: II 1G Ex ia IIC T5 Ga
Relative Humidity: ¨Q85%
Pressure: 86kPa -106kPa
Signal Output: 4-20mA,Pulse Communication: RS485 MODBUS or HART

Intelligent vortex flow meter will enjoy good Linearity, Repeatability and accuracy level under professional calibrastion, each of QT vortex meter will carry out calibration before leave factory.
Measured medium: liquid,gas,steam;
Medium Temp: -40¡æ~250¡æ,-40¡æ~350¡æ,
Nominal Pressure: 1.6MPa
Flow Range: Liquid:0.4-7.0m/s,Gas:4.0-60.0m/s,Steam:5.0-70.0m/s,
Specifications: DN100-2000 (Insertion),
Material: SS304(Standard),SS316(Optional)
Vibration Acceleration Allowed: ¨Q0.2g
IEP ATEX: II 1G Ex ia IIC T5 Ga
Ambient Condition: Ambient temp: -40¡æ~65¡æ (Non-explosion-proof site), -20¡æ~55¡æ (Explosion-proof site)

Vortex steam flowmeter has flange,wafer,triclamp,insertion connection etc,steam vortex flow meter output signals 4-20mA, pulses, HART or MODBUS? RTU are available. Size: DN15-DN6000; Measured medium: liquid,gas,steam; Medium Temp: -40¡æ~250¡æ,-40¡æ~350¡æ,
¡À1.5 % (Insertion type) Flow Range: Liquid:0.4-7.0m/s,Gas:4.0-60.0m/s,Steam:5.0-70.0m/s,
Specifications: DN100-2000 (Insertion),
Material: SS304(Standard),SS316(Optional)
Accuracy: ¡À1.0 % (Flange / wafer / thread / tri-clamp; ¡À1.5 % (Insertion type)
Pressure: 86kPa -106kPa

Vapor vortex flowmeter works on the Karman vortex street principle that swirls generated by a bluff body in the pipe.Vortex flow meter’s number of swirls are proportional to the volumetric flow in the pipe. Size: DN15-DN6000; Measured medium: liquid,gas,steam; Medium Temp: -40¡æ~250¡æ,-40¡æ~350¡æ,
Nominal Pressure: 1.6MPa
Accuracy: ¡À1.0 % (Flange / wafer / thread / tri-clamp; ¡À1.5 % (Insertion type) Flow Range: Liquid:0.4-7.0m/s,Gas:4.0-60.0m/s,Steam:5.0-70.0m/s,
Specifications: DN100-2000 (Insertion),
Material: SS304(Standard),SS316(Optional)
Vibration Acceleration Allowed: ¨Q0.2g

Flowmeter vortex specially for flow measurement of gases and liquids in industry pipeline,vortex liquid mass flow meter requires strict calibration with higher accuracy before leave factory. Size: DN15-DN6000; Measured medium: liquid,gas,steam; Medium Temp: -40¡æ~250¡æ,-40¡æ~350¡æ,
¡À1.5 % (Insertion type) Flow Range: Liquid:0.4-7.0m/s,Gas:4.0-60.0m/s,Steam:5.0-70.0m/s,
Specifications: DN100-2000 (Insertion),
Material: SS304(Standard),SS316(Optional)
Vibration Acceleration Allowed: ¨Q0.2g
Pressure: 86kPa -106kPa

Q&T vortex liquid mass flow meter calibration adopt the pulse signal to calibrate the vortex flow meter, 5 testing points and each points run three times to guarantee the accuracy. Measured medium: liquid,gas,steam; Medium Temp: -40¡æ~250¡æ,-40¡æ~350¡æ,
Nominal Pressure: 1.6MPa
Flow Range: Liquid:0.4-7.0m/s,Gas:4.0-60.0m/s,Steam:5.0-70.0m/s,
Specifications: DN100-2000 (Insertion),
Material: SS304(Standard),SS316(Optional)
Vibration Acceleration Allowed: ¨Q0.2g
Relative Humidity: ¨Q85%

Mass flow meter steam flow meter is applicable for liquid or gas measurement,the liquid vortex meter and steam vortex meter with different k factor guarantee the accuracy. Size: DN15-DN6000; Measured medium: liquid,gas,steam; Medium Temp: -40¡æ~250¡æ,-40¡æ~350¡æ,
Accuracy: ¡À1.0 % (Flange / wafer / thread / tri-clamp; ¡À1.5 % (Insertion type)
Specifications: DN100-2000 (Insertion),
Material: SS304(Standard),SS316(Optional) Signal Output: 4-20mA,Pulse Communication: RS485 MODBUS or HART

Mass flow meter steam flow meter has flange,wafer,triclamp,insertion connection etc,vapor mass flowmeter steam flow meter output signals 4-20mA, pulses, HART or MODBUS? RTU are available. Size: DN15-DN6000; Measured medium: liquid,gas,steam; Medium Temp: -40¡æ~250¡æ,-40¡æ~350¡æ,
¡À1.5 % (Insertion type) Flow Range: Liquid:0.4-7.0m/s,Gas:4.0-60.0m/s,Steam:5.0-70.0m/s,
Specifications: DN100-2000 (Insertion),
Material: SS304(Standard),SS316(Optional)
Accuracy: ¡À1.0 % (Flange / wafer / thread / tri-clamp; ¡À1.5 % (Insertion type)
Pressure: 86kPa -106kPa

Gas vortex flowmeter is populasr in power generation and heat-supply systems involve widely differing fluids: saturated steam, superheated steam, compressed air, nitrogen, liquefied gases,etc.
Specifications: DN100-2000 (Insertion),
Material: SS304(Standard),SS316(Optional)
Vibration Acceleration Allowed: ¨Q0.2g
IEP ATEX: II 1G Ex ia IIC T5 Ga
Ambient Condition: Ambient temp: -40¡æ~65¡æ (Non-explosion-proof site), -20¡æ~55¡æ (Explosion-proof site)
Relative Humidity: ¨Q85%
Pressure: 86kPa -106kPa
Power Supply: DC 12-30V or 3.6V battery powered
Signal Output: 4-20mA,Pulse
Communication: RS485 MODBUS or HART

Palm oil vortex flowmeter adopts Japan technology,with military regulation SS304 or SS316 sensor,guarantee the accuracy and stability of vortex flow meter. Size: DN15-DN6000;
Accuracy: ¡À1.0 % (Flange/wafer/thread/tri-clamp; ¡À1.5%(Insertion type)
Specifications: DN100-2000 (Insertion),
Material: SS304(Standard),SS316(Optional)
Vibration Acceleration Allowed: ¨Q0.2g
IEP ATEX: II 1G Ex ia IIC T5 Ga
Relative Humidity: ¨Q85%
Pressure: 86kPa -106kPa

Vapor vortex flowmeter adopt gas venturi nozzle system carry out the calibration,accuracy with ¡À1.0%, every steam flowmeter will be well calibrated before leave factory. Size: DN15-DN6000; Measured medium: liquid,gas,steam; Medium Temp: -40¡æ~250¡æ,-40¡æ~350¡æ,
Nominal Pressure: 1.6MPa
Accuracy: ¡À1.0 % (Flange / wafer / thread / tri-clamp; ¡À1.5 % (Insertion type) Flow Range: Liquid:0.4-7.0m/s,Gas:4.0-60.0m/s,Steam:5.0-70.0m/s,
Specifications: DN100-2000 (Insertion),
Material: SS304(Standard),SS316(Optional)
Vibration Acceleration Allowed: ¨Q0.2g

Air flowmeter vortex flowmeter appilable for gases, steam and liquid applications. flowmeter is ideal for measuring saturated and superheated steam in factroy and improve steam production efficiency. Measured medium:liquid,gas,steam;Medium Temp:-40¡æ~250¡æ,-40¡æ~350¡æ,
Accuracy:¡À1.0 %(Flange/wafer/thread/tri-clamp; ¡À1.5 %(Insertion type) Flow Range:Liquid:0.4-7.0m/s,Gas:4.0-60.0m/s,Steam:5.0-70.0m/s,
Specifications: DN100-2000 (Insertion),
Material: SS304(Standard),SS316(Optional)
IEP ATEX: II 1G Ex ia IIC T5 Ga
Relative Humidity: ¨Q85%
Pressure: 86kPa -106kPa

Smart vortex flow meter specially for flow measurement of gases and liquids in industry pipeline,vortex flow meter requires higher accuacy before leave factory.
Size: DN15-DN6000
Measured medium: liquid,gas,steam;
Medium Temp: -40¡æ~250¡æ,-40¡æ~350¡æ,¡À1.5 % (Insertion type)
Flow Range: Liquid:0.4-7.0m/s,Gas:4.0-60.0m/s,Steam:5.0-70.0m/s
Specifications: DN100-2000 (Insertion)
Material: SS304(Standard),SS316(Optional)
Vibration Acceleration Allowed: ¨Q0.2g
Pressure: 86kPa -106kPa

Vortex air flow meter will under strict calibration then could guarantee better accuracy,with gas venturi nozzle realize field real flow calibration for every air flowmeter. Size: DN15-DN6000; Measured medium: liquid,gas,steam; Medium Temp: -40¡æ~250¡æ,-40¡æ~350¡æ,
Nominal Pressure: 1.6MPa
Accuracy: ¡À1.0 % (Flange / wafer / thread / tri-clamp; ¡À1.5 % (Insertion type) Flow Range: Liquid:0.4-7.0m/s,Gas:4.0-60.0m/s,Steam:5.0-70.0m/s,
Specifications: DN100-2000 (Insertion),
Material: SS304(Standard),SS316(Optional)
Power Supply: DC 12-30V or 3.6V battery powered

Vortex flow meter adopts Japan technology to improve product stability and accuracy. Achieve high accuracy ¡À0.75% of reading in liquids measurement, ¡À1.0% of reading in steam or gas flow measurement.
Size: DN15-DN6000
Measured medium: liquid,gas,steam; Medium Temp: -40¡æ~250¡æ,-40¡æ~350¡æ
Nominal Pressure: 1.6MPa
Flow Range: Liquid:0.4-7.0m/s,Gas:4.0-60.0m/s,Steam:5.0-70.0m/s,
Specifications: DN100-2000 (Insertion)
Material: SS304(Standard),SS316(Optional)
Vibration Acceleration Allowed: ¨Q0.2g
Relative Humidity: ¨Q85%
Power Supply: DC 12-30V or 3.6V battery powered
Signal Output: 4-20mA,Pulse

Triclamp vortex flow meter adopt the sanitary connection, the triclamp could remove during calibration, sanitary vortex flow meter applicable for RO water, juice or other mediums.
Measured medium: liquid,gas,steam; Medium Temp: -40¡æ~250¡æ,-40¡æ~350¡æ
Accuracy: ¡À1.0 % (Flange / wafer / thread / tri-clamp, ¡À1.5 % (Insertion type)
Flow Range: Liquid:0.4-7.0m/s,Gas:4.0-60.0m/s,Steam:5.0-70.0m/s,
Specifications: DN100-2000 (Insertion)
Material: SS304(Standard),SS316(Optional)
IEP ATEX: II 1G Ex ia IIC T5 Ga
Relative Humidity: ¨Q85%
Pressure: 86kPa -106kPa

Vortex liquid mass flow meter adopt gas venturi nozzle system carry out the calibration,accuracy with ¡À1.0%,every vortex liquid mass flowmeter will be well calibrated before leave factory. Size: DN15-DN6000;
Accuracy: ¡À1.0 % (Flange / wafer / thread / tri-clamp; ¡À1.5 % (Insertion type)
Specifications: DN100-2000 (Insertion),
Material: SS304(Standard),SS316(Optional)
Vibration Acceleration Allowed: ¨Q0.2g
IEP ATEX: II 1G Ex ia IIC T5 Ga
Relative Humidity: ¨Q85%
Pressure: 86kPa -106kPa

Vortex liquid mass flowmeter can be installed vertically,horizontally,or at any angle,as long as they are kept flooded. The meter can be kept flooded by installing it in a vertical upward flow line.
Accuracy: ¡À1.0 % (Flange / wafer / thread / tri-clamp, ¡À1.5 % (Insertion type)
Flow Range: Liquid:0.4-7.0m/s,Gas:4.0-60.0m/s,Steam:5.0-70.0m/s,
Specifications: DN100-2000 (Insertion)
Material: SS304(Standard),SS316(Optional)
Vibration Acceleration Allowed: ¨Q0.2g
IEP ATEX: II 1G Ex ia IIC T5 Ga
Ambient Condition: Ambient temp: -40¡æ~65¡æ (Non-explosion-proof site), -20¡æ~55¡æ (Explosion-proof site)
Relative Humidity: ¨Q85%
Pressure: 86kPa -106kPa
Power Supply: DC 12-30V or 3.6V battery powered

Steam flow meter adopt gas venturi nozzle system carry out the calibration,accuracy with ±1.0%,every flow meter will be well calibrated before leave factory.
Size: DN15-DN6000;
Accuracy: ±1.0 % (Flange / wafer / thread / tri-clamp; ±1.5 % (Insertion type)
Specifications: DN100-2000 (Insertion),
Material: SS304(Standard),SS316(Optional)
Vibration Acceleration Allowed: ¨Q0.2g
IEP ATEX: II 1G Ex ia IIC T5 Ga
Relative Humidity: ≤85%
Pressure: 86kPa -106kPa

Q&T vortex liquid mass flowmeter will enjoy good Linearity, Repeatability and accuracy level under professional calibration,each of QT vortex meter will under strict calibration before delivery. Measured medium: liquid,gas,steam; Medium Temp: -40¡æ~250¡æ,-40¡æ~350¡æ,
Nominal Pressure: 1.6MPa
Flow Range: Liquid:0.4-7.0m/s,Gas:4.0-60.0m/s,Steam:5.0-70.0m/s,
Specifications: DN100-2000 (Insertion),
Material: SS304(Standard),SS316(Optional)
Vibration Acceleration Allowed: ¨Q0.2g
IEP ATEX: II 1G Ex ia IIC T5 Ga
Ambient Condition: Ambient temp: -40¡æ~65¡æ (Non-explosion-proof site), -20¡æ~55¡æ (Explosion-proof site)

RS485 MODBUS vortex flow meter 4-20mA specially for flow measurement of gases and liquids in industry pipeline,vortex flowmeter requires higher accuracy before leave factory. Size: DN15-DN6000; Measured medium: liquid,gas,steam; Medium Temp: -40¡æ~250¡æ,-40¡æ~350¡æ,
¡À1.5 % (Insertion type) Flow Range: Liquid:0.4-7.0m/s,Gas:4.0-60.0m/s,Steam:5.0-70.0m/s,
Specifications: DN100-2000 (Insertion),
Material: SS304(Standard),SS316(Optional)
Vibration Acceleration Allowed: ¨Q0.2g
Pressure: 86kPa -106kPa