Handheld Ultrasonic Water flow sensor portable flow meter

Handheld Ultrasonic Flowmeter Clamp on Flow Meter Portable Liquid Flow Meter with small transducer to measure flow rate through the pipe wall, the transit time ultrasonic flow principle. It is a 3.6V battery powered ultrsonic flow meter, for using on a wide range of sizes and can provide 24 hours measurement continuely. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring clean liquids Built-in rechargeable battery 3.6V 2000 lines storage Communication: RS232

Ultrasonic Water Flow Meter DN50-DN400 Sewage Water Ultrasonic Flow Meter is a portable liquid flow measurement device with a sensor. Hot sales portable ultrasonic flowmeter handheld water flow meter adopt transit-time ultrasonic measurement technology for superior accuracy and ease of installation and installation. This easy-to-use flowmeter comes in a rugged, waterproof carrying case for easy transport of the display, sensor, and cables between measurement locations. High accuracy +/-1.0% of FS Transducer temperature: -30~90¡ãC/-30¡ãC~160¡ãC Measuring clean liquids Battery-powered,for 12 hours Communication: RS232

PLCM open channel meter is good for Flow Measurement in Open Channel,river; it is a high quality water flow meters, RS485 River Flow Meter; This ultrasonic open channel flow meter is Suitable for a variety of weirs and flumes, Parshall flumes (ISO), V-Notch weirs, Rectangular weirs(With or Without End Contractions) and custom Formula type weir; LCD display with backlight
Accuracy of Change in Level: 1mm or 0.2% of full span (whichever is greater)
Resolution: 1mm
Analogue Output: 4-20mA, corresponding to instantaneous flow
Relays Output: Standard 2 relay outputs(Optional up to 6 relays)
Serial Communication: RS485, MODBUS -RTU standard protocol
Ambient Temperature: -40 ~70 Degree C
Measure Cycle: 1 second (selectable 2 seconds )
Power Supply: DC24V (+5%) 0.2A; AC220V (+20%) 0.1A ;Optional DC12V

Inline ultrasonic water flow meter could be manufactured from 50mm~700mm and suitable for continuously measuring flow and heat of clean and uniform liquids without large concentration suspended particles or gases industrial environment.
Input:Two-wire PT1000
Output:4-20mA,Pulse,OCT
Communication:RS485
Szie:DN15~DN6000
Accuracy:¡À1.0 %
Viscosity:0.1~¡À10m/s

High Frequency portable clamp on ultrasonic flow meter no pipe cutting required. The user simply clamp on the flow sensor to the pipe surface. The High Frequency portable clamp on ultrasonic flow meter can then detect the flow through ultrasonic waves, and then automatically calculate the flow rate value, flow accumulator, etc. No pipe cutting means no damage to the pipe. So as long as the pipes are in good condition, the installation on the flowmeter will not provide the possibility of leakage. Sensor: Clamp-on/External Principle: transmit time Size: DN15mm-DN6000mm Measuring medium: Liquid 3.6V Battery-powered

QT811 clamp on type ultrasonic flow meters suitable for various liquids and compatible with various pipeline materials and sizes.
Specially external clamp design, QT811 clamp on ultrasonic energy BTU meter could
get the flow rate without touch the measurement medium.
Compared with other traditional type flow meters, QT811 clamp on ultrasonic meters could avoid
pressure loss or media contamination problems.

Pipe Size:?DN15-DN40mm (1/2¡±~1 1/2¡±)
Flow Range:¡À0.1m/s ~¡À5m/s
Temperature: 0~75¡æ (standard)
Output: 4-20mA, OCT Pulse, RS485
Accuracy:?¡À1% of measured value
Power Supply: DC10-24V

Plastic Ultrasonic Liquid flow Meter sensors can be mounted outside, plug-in, pipeline-type installation; Used for measuring liquids, such as ultrapure liquids, chemicals, raw sewage, reclaimed water, cooling water, river water, plant sewage, etc.
Protection: IP57
Power supply: 8-36VDC
Output: RS485,4-20mA and OCTPipe diameters from 15mm to 6000mmDisplay: 2¡Á20 English letters LCD
Keypad: 4 key tactile-feedback membranelnput:4-20mA and PT100 platinum resistancelnstallation: Operate with clamp on, insertion and
flow-cell transducer

QT811 external clamp on ultraonic flow meter is an easy operation instrument for non-invasive, quick flow and energy measurement with clamp-on technology for many types of pipings.QT811 clamp on flow meter support user to monitor the flow rate reading directly on the device. With various kinds of outputs signals, could send the information to PLC,
central control room and etc.

Pipe Size:?DN15-DN40mm (1/2¡±~1 1/2¡±)
Flow Range:¡À0.1m/s ~¡À5m/s
Temperature: 0~75¡æ (standard)
Output: 4-20mA, OCT Pulse, RS485
Accuracy:?¡À1% of measured value
Power Supply: DC10-24V

Q&T 4-20mA output Open Channel flow meter measures level, flow rate and total volume of water flowing through weirs, flumes and channels. The flow meters use a non-contact level sensor. Application field£ºWater and sewage treatment£ºpump room, collection well, biochemical reaction
tank, sedimentation tank. And Electricity, mines£ºmortar pool, coal slurry pool, butter storage tank, stockyard or some mobile equipment control etc. And Food industry£ºwineries, granaries, storage tanks for food materials, etc.

Specifications:
Display: Backlight?LCD
The?maximum?of Accumulative Flow: 9999999.9?m3/h
Resolution: 1mm
Analogue?Output: 4-20mA
Relays?Output: Standard?2?relay?outputs(Optional?up?to?6?relays)
Serial?Communication: RS485,?MODBUS RTU
Ambient?Temperature: -40 ~70 Degree C
Power?Supply: DC24V, AC 220V£»Optional?DC12V

Q&T Factory PLCM open channel flow meter work together with Rectangular weir, it is cost effective Open Channel Measuring Instrument, excellent choice for open channel Ultrasonic Water Flow Meter.
Display: Backlight LCD
The maximum of Accumulative Flow: 9999999.9 m3/h
Accuracy of Change in Level: 1mm or 0.2% of full span (whichever is greater)
Resolution: 1mm
Analogue Output: 4-20mA, corresponding to instantaneous flow
Relays Output: Standard 2 relay outputs(Optional up to 6 relays)
Serial Communication: RS485, MODBUS -RTU standard protocol
Ambient Temperature: -40 ~70 Degree C
Power Supply: DC24V (+5%) 0.2A; AC220V (+20%) 0.1A ;Optional DC12V

Fixed type ultrasonic flowmeter enjoy easy&simple installation,higher flexibility,ultrasonic flow meter has DN25-1200 one pair clamp on sensor is workable with most of the pipe size. Transmitter material: PC/ABS, IP65;
Transducer:ABS,IP68
Accuracy:±1% of measured value;
Repeatability:0.2% of measured value;
Linearity:±1%;

QT621 ultrasonic flow meter is a type of portable flow meter, main advantage is that the meter can be easily moved and installed in different pipes and convenient to carry site to site. Portable ultrasonic flow meter adopt the innovative design includes matched precision transducers
and signal processing circuitry to accurately measure the flow of most liquids over a wide range of velocities.

Size: 1¡å~48¡å(25mm~1200mm)
Flow Range:¡À0.01 m/s~ ¡À12 m/s
Accuracy: ¡À1%
Repeatability: 0.2%
Output: 4-20mA, RS485
Power supply: Internal lithium 3000mAh
Transducer: IP68

Industrial ultrasonic flow meter output for water ultrasonic flow meter pvc pipe heat meter is a ideal for liquids such as chemical,visous liquids, and sea water. The non-intrusive, clamp-on ultrasonic flow meter fits pipes between 1/2″ to 48″ internal diameter. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Medium: clean liquids,pure water Built-in rechargeable battery 3.6V Measurment unit: Meter, Feet,Cubic Meter.

Digital Ultrasonic Flow Meter Rotameter Stainless Steel DN15 portable ultrasonic flow meter is an ultrasonic flowmeter used to measure the flow rate of liquids in closed pipes. The transducer is clamp-on type, which will provide the benefits of contamination-free operation and ease of installation. The transit time flowmeter includes two transducers, which act as ultrasonic transmitters and receivers. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring clean liquids Power supply: 24VDC/85VAC-2265AC Communication: RS485

This transit-time open Channel flow meter can be used for continuous measuring of municipal rain-water, wastewater, sewage discharge and irrigation water pipelines. This Open Channel flow meter measures level, flow rate and total volume of water flowing through weirs, flumes, and channels etc.

Specifications:
Display: Backlight?LCD
Flow?Rate?Range: 0.0000~99999L/S?or?m3/h
The?maximum?of Accumulative Flow: 9999999.9?m3/h
Accuracy?of?Change in Level: 1mm?or?0.2%?of?full?span?(whichever?is?greater)
Resolution: 1mm
Analogue?Output: 4-20mA,?corresponding?to?instantaneous?flow
Relays?Output: Standard?2?relay?outputs(Optional?up?to?6?relays)
Serial?Communication: RS485,?MODBUS?-RTU?standard?protocol

QT621 handheld ultrasonic flow meter support accurate bidirectional and highly dynamic flow measurement
with the non-invasive clamp-on technology. Handheld type ultrasonic flow meter mainly applies for measuring the flow of homogeneous medium fluid in the water injection flow measurement, raw water flow measurement, tap water flow measurement etc.

Size: 1¡å~48¡å(25mm~1200mm)
Flow Range:¡À0.01 m/s~ ¡À12 m/s
Accuracy: ¡À1%
Repeatability: 0.2%
Output: 4-20mA, RS485
Power supply: Internal lithium 3000mAh
Transducer: IP68

This ultrasonic water flow meter can directly display the instantaneous and cumulative flow. This Non-contact ultrasonic flow meter is based on the flow rate-water level calculation method, and adopts an advanced flow rate measuring instrument and water level measuring instrument to ensure a new intelligent flow system.

Specifications:
Sensor?Level?Range: 0-4.0m; other?level?range?also?available
Blind?zone: 0.20m
Temperature?Compensation: Integral?in?probe
Pressure?Rating: 0.2MPa
Beam?Angle: 8*?(3db)
Cable?Length: 10m?standard?(can?be?extended?to?1000m)
Sensor?Material: ABS,?PVC?or?PTFE?(optional)
Sensor?Protection Class: IP68
Output: 4-20mA, Relays, RS485

Q&T Handheld ultrasonic flowmeter measure flow rate by propagating ultrasound waves into liquid-filled pipes and measuring the flow. With transit time, these clamp-on ultrasonic meters are outside the pipe, providing a wide range of pipe sizes, no pressure loss, none contact with internal liquid and no moving parts.
Measuring accuracy: +/-1.0% of FS
Wide range: DN15mm-DN6000mm
Measuring clean liquids
Built-in rechargeable battery 3.6V
Communication: RS232

Perfect Quality Economical Ultrasonic Flow meter insertion type ultrasonic flowmeter is a high precision no-cut tube measurement method. This special design includes matching sensors for ease of use and is ideal for installation in existing systems Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring single clean liquids Power supply: 24VDC/85VAC-2265AC Storage: SD card optional Heat meter optional

This solar power Open channel flow meter require accurate measurement of the surface level of a liquid. A flume, channel or structure which has a known characteristic flow per measured head, together with the measured liquid level, accurately define the flow rate through the system.
Applications including Wastewater collection systems,combined sewer systems and outfalls, Wastewater treatment facilities,Irrigation canals and channels, Industrial process and discharges, Stormwater conveyance and outfalls.

Specifications:
Analogue?Output: 4-20mA,?corresponding?to?instantaneous?flow
Relays?Output: Standard?2?relay?outputs(Optional?up?to?6?relays)
Serial?Communication: RS485,?MODBUS?-RTU?standard?protocol
Ambient?Temperature: -40 ~70 Degree C
Measure?Cycle: 1?second?(selectable?2?seconds?)
Power?Supply: DC24V?(+5%)?0.2A;?AC220V?(+20%)?0.1A?;Optional?DC12V

QT621 handheld ultrasonic flow meter support to carry from site to site conveniently. Support accurate bidirectional and highly dynamic flow measurement with the non-invasive clamp-on technology. Portable ultrasonic flow meter mainly applies for measuring the flow of homogeneous medium fluid in the water injection flow measurement, raw water flow measurement, tap water flow measurement etc.

Size: 1¡å~48¡å(25mm~1200mm)
Flow Range:¡À0.01 m/s~ ¡À12 m/s
Accuracy: ¡À1%
Repeatability: 0.2%
Output: 4-20mA, RS485
Power supply: Internal lithium 3000mAh
Transducer: IP68

Q&T Wall mounted ultrasonic flowmeter clamp on type transducer is a high precision no-cut tube measurement method. This special design includes matching sensors for ease of use and is ideal for installation in existing systems Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring single clean liquids Power supply: 24VDC/85VAC-2265AC Storage: SD card optional Heat meter optional

Wall mounted inline ultrasonic flow meter is a popular solution to simplify flow measurement across a variety of applications.
Higher accuracy across a wide range of applications compared to mechanical meters.
Can be installed permanently or temporarily
Feature a streamlined design without moving parts, which results in minimal maintenance and low cost of installation and ownership.
Input:Two-wire PT1000
Output:4~20mA,Pulse,OCT,RS485
Body material:Standard carbon steel,SS304 and SS316 are optional
Power supply:DC24V and AC220V
Connection way:Flange type
Media temperature :-30~+150¡æ

Q&T brand pulse output ultrasonic flow meter is one kind of economy type flow meter for liquid,multi channle inline ultrasonic flow meter accuracy less 0.5%
OCT output
RS485 communication
Input:Two-wire PT1000
Measuring cycle:50mS
Output:4~20mA,Pulse,OCT,RS485
Body material:Standard carbon steel,SS304 and SS316 are optional
Power supply:DC24V and AC220V

Modular type ultrasonic flow meter is one type of ultrasonic flow meter.It has very small size and easy to be installed into instrument box. This type flow is working with clamp type transducer normally. The max measure tube is DN3000 pipe. It have 4-02mA, pulse, and RS485 output also.It even could link with temperature sensor and work as ultrasonic BTU meter.
Accuracy: ±1%
Velocity: 0.5s
Display: LCD with backlight 2*20leters
Signal Outputs: 4-20mA or o-20mA,RS485,Pulse
Liquid Types: Virtually all commonly used liquids
Pipe Size: DN15-DN3000

Q&T Clamp-on Portable ultrasonic flow meter is the non-invasive method of high accurate flow measurement. The special design includes matching senssors for ease of use ideal for installation in existing systems. The QTDS-100H is designed for ?¡± to 240¡±.
Measuring accuracy: +/-1.0% of FS
Transducer temperature: -30~90¡ãC/-30¡ãC~160¡ãC
Measuring clean liquids
Built-in rechargeable battery 3.6V
Communication: RS232

Q&T river flow meter can directly display the instant and accumulative flow. This Open Channel Water Meter is based on the flow rate-water level calculation method, and adopts an advanced flow rate measuring instrument and water level measuring instrument to ensure a new intelligent high quality flow system.

Specifications:
Sensor?Level?Range: 0-4.0m; other?level?range?also?available
Blind?zone: 0.20m
Temperature?Compensation: Integral?in?probe
Pressure?Rating: 0.2MPa
Beam?Angle: 8*?(3db)
Cable?Length: 10m?standard?(can?be?extended?to?1000m)
Sensor?Material: ABS,?PVC?or?PTFE?(optional)
Sensor?Protection Class: IP68
Output: 4-20mA, Relays, RS485

Handheld Ultrasonic Water flow sensor portable flow meter no pipe cutting required. The user simply clamp on the flow sensor to the pipe surface. Handheld Ultrasonic Water flow sensor portable flow meter can then detect the flow through ultrasonic waves, and then automatically calculate the flow rate value, flow accumulator, etc. No pipe cutting means no damage to the pipe. So as long as the pipes are in good condition, the installation on the flowmeter will not provide the possibility of leakage. Sensor: Clamp-on/External Principle: transmit time Size: DN15mm-DN6000mm Measuring medium: Liquid 3.6V Battery-powered

RS232 3.6V Lithium Battery Digital Water Handheld Ultrasonic Flow Meter is a non-contact instrument, which can measure the flow of medium with large diameter and can also be used for the measurement of medium that is not easy to contact and observe. Digital Water Handheld Ultrasonic Flow Meter measurement accuracy is very high, and it is hardly disturbed by various parameters of the measured medium.
Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Medium: clean liquids,pure water Built-in rechargeable battery 3.6V Communication: RS232

wall mounted Clamp on pipe ultrasonic water flow meter price adopts the self-development measurement technology.This measurement technique is a faster and more accurate process time measurement. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring single clean liquids Power supply: 24VDC/85VAC-2265AC Communication: RS485