dynamic flow measurement Handheld digital water portable ultrasonic flow meter

Ultrasonic flow wall mounted water flow meter Modbus flow meter measure flow by propagating ultrasonic waves into a liquid-filled pipe. These Ultrasonic flow wall mounted water flow meter Modbus flow meter are located outside the pipeline and offer a wide range of pipeline sizes with no pressure loss, no contact with the liquid inside, and no moving parts. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm None cut down pipe Power supply: 24VDC/85VAC-2265AC Communication: RS485

Ultrasonic Flow meter for applications in clean water and in low conductivity media. Operating principle based on transit time measurement.
High Isolation voltage,Strong anti-interference,Suppress voltage noise,Good isolation performance
Inline ultrasonic flow meter collect temperature signal and accuracy reach 0.001¡æ
When using inline ultrasonic flow meter to measure,allowing pipe with liner
Szie:DN15~DN6000
Accuracy:¡À1.0 %
Viscosity:0.1~¡À10m/s
Output:4~20mA,Pulse,OCT,RS485
Power supply:DC24V and AC220V
Connection way:Flange type

This solar power open Channel flow meter can be used for continuous measuring of municipal rain-water, wastewater, sewage discharge and irrigation water pipelines. This Open Channel flow meter measures level, flow rate and total volume of water flowing through weirs, flumes, and channels etc.

Specifications:
Display: Backlight?LCD
Flow?Rate?Range: 0.0000~99999L/S?or?m3/h
The?maximum?of Accumulative Flow: 9999999.9?m3/h
Accuracy?of?Change in Level: 1mm?or?0.2%?of?full?span?(whichever?is?greater)
Resolution: 1mm
Analogue?Output: 4-20mA,?corresponding?to?instantaneous?flow
Relays?Output: Standard?2?relay?outputs(Optional?up?to?6?relays)
Serial?Communication: RS485,?MODBUS?-RTU?standard?protocol

PN16 Flowmeter Water Wall Mounted Clamp On Ultrasonic Flow Meter Digital Water proven transit-time ultrasonic measurement technology .This technology can be used for permanent installations where intrusive flow meters are not economically viable for permanent installations on large pipelines and for all the different process fluids encountered in the network. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring clean liquids Power supply: 24VDC/85VAC-2265AC Communication: RS485

PLCM series ultrasonic open channel flow meter is a low cost choice. It is a hot sell product for river channel measuring. The product supports weirs or notches of different standards in various countries and can be widely used for measurement or monitoring of total water drainage.
Display: Backlight LCD
The maximum of Accumulative Flow: 9999999.9 m3/h
Accuracy of Change in Level: 1mm or 0.2% of full span (whichever is greater)
Resolution: 1mm
Analogue Output: 4-20mA, corresponding to instantaneous flow
Relays Output: Standard 2 relay outputs(Optional up to 6 relays)
Serial Communication: RS485, MODBUS -RTU standard protocol
Ambient Temperature: -40 ~70 Degree C
Power Supply: DC24V (+5%) 0.2A; AC220V (+20%) 0.1A ;Optional DC12V

According to market request,the power supply can 24VDC or 220VAC or solar powered;Current the solar powered ultrasonic flow meter is more popular,beacuse solar powered meets international requirements, energy saving and environmental protection.
2 way input
4-20mA,Pulse,OCT,RS485
Bi-directional flow measurement
Backlit LCD

The ultrasonic open channel flowmeter can be equipped with a communication interface, which is easy to connect with SCADA systems to achieve industrial remote monitoring and control. This Open Channel flow meter measures level, flow rate and total volume of water flowing through weirs, flumes, and channels etc.

Specifications:
Sensor?Level?Range: 0-4.0m; other?level?range?also?available
Blind?zone: 0.20m
Temperature?Compensation: Integral?in?probe
Pressure?Rating: 0.2MPa
Beam?Angle: 8*?(3db)
Cable?Length: 10m?standard?(can?be?extended?to?1000m)
Sensor?Material: ABS,?PVC?or?PTFE?(optional)
Sensor?Protection Class: IP68

China Supplier LCD Displayer Digital Water Flow Meter and Ultrasonic Flow Meter Price is a portable liquid flow measurement device with a sensor. Hot sales portable ultrasonic flowmeter handheld water flow meter adopt transit-time ultrasonic measurement technology for superior accuracy and ease of installation and installation. This easy-to-use flowmeter comes in a rugged, waterproof carrying case for easy transport of the display, sensor, and cables between measurement locations. High accuracy +/-1.0% of FS Transducer temperature: -30~90¡ãC/-30¡ãC~160¡ãC Measuring clean liquids Battery-powered,for 12 hours Communication: RS232

This liquid flow meter for industrial is easy and accurate flow measurement without interrupting the process, Clamp-on type transducer easily mountable on existing pipes, non-invasive type.Suitable for most of applications. Measuring accuracy: +/-1.0% of FS Transducer temperature: -30~90¡ãC/-30¡ãC~160¡ãC Measuring clean liquids Built-in rechargeable battery 3.6V Communication: RS232

Clamp on ultrasonic flow meter are widely used in tap water, heating, water conservancy, metallurgy, chemical industry, machinery, energy and other industries. Portable Hand Held Ultrasonic Flow Meter can be used for production monitoring, flow verification, temporary detection, flow inspection, water meter balance debugging, heat network balance debugging, and energy-saving monitoring. Measuring accuracy: +/-1.0% of FS Transducer temperature: -30~90¡ãC/-30¡ãC~160¡ãC Measuring clean liquids Battery-powered,for 12 hours Communication: RS232

QT621 portable type ultrasonic clamp on flow meters support quite quick verify the flow reading of another meter and to data log flow system values over an extended time period.
Portable ultrasonic flow meter uses clamp-on transducers that are mounted externally on the surface of the pipe and which generate pulses that pass through the pipe wall.

Size: 1¡å~48¡å(25mm~1200mm)
Flow Range:¡À0.01 m/s~ ¡À12 m/s
Accuracy: ¡À1%
Repeatability: 0.2%
Output: 4-20mA, RS485
Power supply: Internal lithium 3000mAh
Transducer: IP68

Flange type ultrasonic flow meter with low voltage operation, multi-pulse transmission, low power consumption,
high reliability, anti-interference.
Inline ultrasonic flow meter could connect temperature sensor to become one calorimeter and widely be used in Process control, Production measurement, Trade settlement.
Accuracy:¡À1.0%
Input:Two-wire PT1000
Output:4-20mA,Pulse,OCT
Communication:RS485

RS232 3.6V Lithium Battery Digital Water Handheld Ultrasonic Flow Meter is a non-contact instrument, which can measure the flow of medium with large diameter and can also be used for the measurement of medium that is not easy to contact and observe. Digital Water Handheld Ultrasonic Flow Meter measurement accuracy is very high, and it is hardly disturbed by various parameters of the measured medium. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Medium: clean liquids,pure water Built-in rechargeable battery 3.6V Housing Material: ABS

QTLD-100F is a fixed wall-mounted ultrasonic flowmeter, which adopts the self-developed time difference measurement technology. Compared with other common algorithms in China, the measurement technology is an algorithm for measuring process time with higher speed and higher precision.
Accuracy: +/-1.0% of FS
Wide range: DN15mm-DN6000mm
Measuring single clean liquids
Power supply: 24VDC/85VAC-2265AC
Communication: RS485

Wall Mounted Ultrasonic Flow Meter consists of two parts: a transmitter unit and a transducer. Magnetic external clamps on the sensor are easy to install and connect to metal tubing for continuous flow measurement. It is especially suitable for on-site flow measurement of various pressure requirements. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring clean liquids Power supply: 24VDC/85VAC-2265AC Communication: RS485

Precise digital display insertion clamp on ultrasonic water flow meter Wall mounted ultrasonic flowmeter is an ultrasonic flowmeter used to measure the flow rate of liquids in closed pipes. The transducer is a non-contact, clamp-on type, which will provide the benefits of contamination-free operation and ease of installation. The transit time flowmeter employs two transducers, which act as ultrasonic transmitters and receivers. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring clean liquids Power supply: 24VDC/85VAC-2265AC Communication: RS485

The majority of wall mount ultrasonic flow meter applied in general industry.liquid ultrasonic flow meter is suitable for measuring variety of different liquids.
Humidity:Up to 99% RH, non-condensing;
Transmitter material: PC/ABS, IP65;
Transducer:ABS,IP68
Accuracy:±1% of measured value;
Repeatability:0.2% of measured value;

Using ultrasonic transit time techniques,Wall Mounted Ultrasonic Water Flowmeter is controlled by a micro-processor system which contains a wide range of data that enables it to be used with pipes with an outside diameter ranging from 15mm up to 1200mm (depending on model) and constructed of almost any material. instrument will also operate over a wide range of fluid temperatures.

clamp on ultrasonic portable liquid flow meter is controlled by a micro-processor system which contains a wide range of data that enables it to be used with pipes with an outside diameter ranging from 15mm up to 1200mm (depending on model) and constructed of almost any material. instrument will also operate over a wide range of fluid temperatures.

DN80 pipe ultrasonic flowmeter water liquid ultrasonic clamp on type is an ultrasonic flowmeter used to measure the flow rate of liquids in closed pipes. The transducer is clamp-on type, which will provide the benefits of contamination-free operation and ease of installation. The transit time flowmeter includes two transducers, which act as ultrasonic transmitters and receivers. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring clean liquids Power supply: 24VDC/85VAC-2265AC Communication: RS485

Solar power GPRS Open Channel Flow Meter river flow meter can directly display the instant and accumulative flow. This Open Channel Water Meter is based on the flow rate-water level calculation method, and adopts an advanced flow rate measuring instrument and water level measuring instrument to ensure a new intelligent high quality flow system.

Specifications:
Sensor?Level?Range: 0-4.0m; other?level?range?also?available
Blind?zone: 0.20m
Temperature?Compensation: Integral?in?probe
Pressure?Rating: 0.2MPa
Beam?Angle: 8*?(3db)
Cable?Length: 10m?standard?(can?be?extended?to?1000m)
Sensor?Material: ABS,?PVC?or?PTFE?(optional)
Sensor?Protection Class: IP68
Output: 4-20mA, Relays, RS485

Q&T brand wall mounted ultrasonic flow meter accuracy is 1.0% and the repeatability can reach 0.2%.
Wall mounted ultraosnic flow meter also can add the RTD function and become BTU meter.
Output:4-20mA,RS485
Transducer temperature:-40~80℃
Transducer protect:IP68
Power supply:24VDC,90~245VAC power is optional
PT1000 is optional
Both clamp on type sensors and insertion type
sensors are available

QT621 ultrasonic flow meter is a type of portable flow meter with the main advantage of support to be easily moved and installed in different pipes and convenient to carry site to site. Portable type ultrasonic flow meters are widely used in all areas such as drinking water and sewerage industry, power plants, producing industry, food industry and so on.

Size: 1¡å~48¡å(25mm~1200mm)
Flow Range:¡À0.01 m/s~ ¡À12 m/s
Accuracy: ¡À1%
Repeatability: 0.2%
Output: 4-20mA, RS485
Power supply: Internal lithium 3000mAh
Transducer: IP68

The PLCM industrial waste water treatment flow meter using transit-time principle, it is an economical ultrasonic flowmeter specifically designed for open channel. Compared with other ultrasonic flow meters on the market, it has the characteristics of high reaction rate, low power consumption and high certainty. At the same time, with non-contact level sensor, it also have the feature of installation simple, easy to use, no need water supply shutdown etc.

Specifications:
Display: Backlight?LCD
Flow?Rate?Range: 0.0000~99999L/S?or?m3/h
The?maximum?of Accumulative Flow: 9999999.9?m3/h
Accuracy?of?Change in Level: 1mm?or?0.2%?of?full?span?(whichever?is?greater)
Resolution: 1mm
Analogue?Output: 4-20mA,?corresponding?to?instantaneous?flow
Relays?Output: Standard?2?relay?outputs(Optional?up?to?6?relays)
Serial?Communication: RS485,?MODBUS?-RTU?standard?protocol

QT621 portable ultrasonic flow meters are with features of for flexibility and performance, providing the user with a comprehensive specification and a list of configuration options. Portable type ultrasonic flow meters are widely used in all areas such as drinking water and sewerage industry, power plants, producing industry, food industry and so on.

Size: 1¡å~48¡å(25mm~1200mm)
Flow Range:¡À0.01 m/s~ ¡À12 m/s
Accuracy: ¡À1%
Repeatability: 0.2%
Output: 4-20mA, RS485
Power supply: Internal lithium 3000mAh
Transducer: IP68

QT621 handheld type ultrasonic water flow meter adopt transit-time principle.Portable ultrasonic flow meter support precise bidirectional and highly dynamic flow measurement with the non-invasive clamp-on technology. Portable ultrasonic flow meter mainly applies for measuring the flow of homogeneous medium fluid .

Size: 1¡å~48¡å(25mm~1200mm)
Flow Range:¡À0.01 m/s~ ¡À12 m/s
Accuracy: ¡À1%
Repeatability: 0.2%
Output: 4-20mA, RS485
Power supply: Internal lithium 3000mAh
Transducer: IP68

QTDS-100H Portable Clamp-on Ultrasonic Flow Meter is a ideal for liquids such as chemical,visous liquids, and sea water. The non-intrusive, clamp-on ultrasonic flow meter fits pipes between 1/2″ to 48″ internal diameter. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Medium: clean liquids,pure water Built-in rechargeable battery 3.6V Measurment unit: Meter, Feet,Cubic Meter.

Portable Hand Held Ultrasonic Flow Meter are widely used in tap water, heating, water conservancy, metallurgy, chemical industry, machinery, energy and other industries. Portable Hand Held Ultrasonic Flow Meter can be used for production monitoring, flow verification, temporary detection, flow inspection, water meter balance debugging, heat network balance debugging, and energy-saving monitoring. Measuring accuracy: +/-1.0% of FS Transducer temperature: -30~90¡ãC/-30¡ãC~160¡ãC Measuring clean liquids Battery-powered,for 12 hours Communication: RS232

QT621 handheld type ultrasonic clamp on flow meters are with user-friendly design, with built-in Lithium battery provides up to 12 hours of measurement operation.
Portable ultrasonic flow meters can be easily moved and installed in different pipes and convenient to carry site to site, which is very convenient for users to monitor the data.

Size: 1¡å~48¡å(25mm~1200mm)
Flow Range:¡À0.01 m/s~ ¡À12 m/s
Accuracy: ¡À1%
Repeatability: 0.2%
Output: 4-20mA, RS485
Power supply: Internal lithium 3000mAh
Transducer: IP68

Handheld ultrasonic clamp on water flow meter flowmeter,hydraulic sewage liquid ultrasonic flow meter sensor can be easily installed, removed and transported. This flowmeter makes them ideal for industrial applications that are already operational or only require occasional flow measurement. In the latter case, the user can use the same clamp on flowmeter to measure flow in multiple locations by unloading and transporting the device for each measurement Measuring accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring clean liquids Built-in rechargeable battery 3.6V Communication: RS232