DN150 ultrasonic flow meter IP67 with clamp on transducers

This Open Channel Water Meters can be widely applied to the environmental protection, water treatment, irrigation, chemical, and other industries. Sewage and rainwater are often transported to the treatment plant in open collection channels or flumes. The flow rate is measured at various points in these channels, and our open channel flow meters are the good choice for these applications.

Specifications:
Display: Backlight?LCD
Flow?Rate?Range: 0.0000~99999L/S?or?m3/h
The?maximum?of Accumulative Flow: 9999999.9?m3/h
Accuracy?of?Change in Level: 1mm?or?0.2%?of?full?span?(whichever?is?greater)
Resolution: 1mm
Analogue?Output: 4-20mA,?corresponding?to?instantaneous?flow
Relays?Output: Standard?2?relay?outputs(Optional?up?to?6?relays)
Serial?Communication: RS485,?MODBUS?-RTU?standard?protocol

QINGTIAN ultrasonic flow meter offer better performance and wide turn-down ratio and non-intrusive sensors that can be installed without cutting into the pipe or stop production. Linearity:±1%;
Pipe size:1″ to 48″ (25mm to 1200mm).Pipe size under 1″ is an option;
Fluid:Water or others;
Flow range:± 0.09ft/s ~ ±16ft/s (±0.03m/s ~ ±5m/s);
Outputs:Analog output:4~20mA,max load 750Ω,Pulse output: 0~10KHz;

Low cost ultrasonic flow meter portable ultrasonic water sensor with high quality no pipe cutting required. The user simply clamp on the flow sensor to the pipe surface.Handheld ultrasonic flow meter transducer with RS232 communication can then detect the flow through ultrasonic waves, and then automatically calculate the flow rate value, flow accumulator, etc. No pipe cutting means no damage to the pipe. So as long as the pipes are in good condition, the installation on the flowmeter will not provide the possibility of leakage. Sensor: Clamp-on/External Principle: transmit time Size: DN15mm-DN6000mm Measuring medium: Liquid 3.6V Battery-powered

The Solar power GPRS Open Channel Flow Meter has 4-20mA and RS485 signal output, it can be equipped with a communication interface, which is easy to connect with SCADA systems to achieve industrial remote monitoring and control. This Open Channel flow meter measures level, flow rate and total volume of water flowing through weirs, flumes, and channels etc.

Specifications:
Sensor?Level?Range: 0-4.0m; other?level?range?also?available
Blind?zone: 0.20m
Temperature?Compensation: Integral?in?probe
Pressure?Rating: 0.2MPa
Beam?Angle: 8*?(3db)
Cable?Length: 10m?standard?(can?be?extended?to?1000m)
Sensor?Material: ABS,?PVC?or?PTFE?(optional)
Sensor?Protection Class: IP68

QT621 Portable ultrasonic flow meter is a portable transit-time ultrasonic flowmeter with clamp-on transducers for non-invasive liquid measurement of clean homgeneous fluids.
Portable ultrasonic flow meter mainly consists of two parts, transmitter and transducer. With 4-20mA and RS485 communication available, QT621 ultrasonic flow meter support quickly verify the flow reading of another meter and to data log flow system values over an extended time period.

Size: 1¡å~48¡å(25mm~1200mm)
Flow Range:¡À0.01 m/s~ ¡À12 m/s
Accuracy: ¡À1%
Repeatability: 0.2%
Output: 4-20mA, RS485
Power supply: Internal lithium 3000mAh
Transducer: IP68

QT621 is a portable transit-time ultrasonic flow meter with advanced functions. Portable ultrasonic flow meter includes matched precision transducers and signal processing circuitry to accurately measure the flow of most liquids. With 4-20mA and RS485 communication available, QT621 support quickly verify the flow reading of another meter and to data log flow system values over an extended time period.

Size: 1¡å~48¡å(25mm~1200mm)
Flow Range:¡À0.01 m/s~ ¡À12 m/s
Accuracy: ¡À1%
Repeatability: 0.2%
Output: 4-20mA, RS485
Power supply: Internal lithium 3000mAh
Transducer: IP68

Pipeline ultraosnic flow meter directly contact the liquid and make the measuring accuracy better than clamp on ultrasonic flowmeter.And installation easy,don’t need calculate the sensor installation distance and cover the coupling agent in the pipe,so this meter can collect the signal very well.

Water flow meter liquid flow meter handheld ultrasonic flow meter use ultrasonic technology to measure the velocity of the liquid. Ultrasonic meters are avaiable as clamp-on solutions. Non pipe cutting, this ultrasonic flow meters can display velocity and accumulated flow. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Medium: clean liquids,pure water Built-in rechargeable battery 3.6V Housing Material: ABS

The structure of 3.6V Waste Water Portable Handheld Ultrasonic Flow Meter is mainly divided into ultrasonic flow unit, flow transducer and information processing circuit, flow display. First, the ultrasonic signal generator is used to send the signal, the sensor receives the signal, and the time difference is obtained. The ultrasonic information is processed according to the information processing circuit, and the flow is transmitted to the display screen in the form of an electrical signal, and the result is displayed Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Medium: clean liquids,pure water Built-in rechargeable battery 3.6V Measurment unit: Meter, Feet,Cubic Meter.

Wastewater ultrasonic flow meter sensor for liquid are widely used in tap water, heating, water conservancy, metallurgy, chemical industry, machinery, energy and other industries. Wastewater ultrasonic flow meter sensor for liquid can be used for production monitoring, flow verification, temporary detection, flow inspection, water meter balance debugging, heat network balance debugging, and energy-saving monitoring. Measuring accuracy: +/-1.0% of FS Transducer temperature: -30~90¡ãC/-30¡ãC~160¡ãC Measuring clean liquids Battery-powered,for 12 hours Communication: RS232

This Open channel flow meter require accurate measurement of the surface level of a liquid. A flume, channel or structure which has a known characteristic flow per measured head, together with the measured liquid level, accurately define the flow rate through the system.
Applications including Wastewater collection systems,combined sewer systems and outfalls, Wastewater treatment facilities,Irrigation canals and channels, Industrial process and discharges, Stormwater conveyance and outfalls.

Specifications:
Analogue?Output: 4-20mA,?corresponding?to?instantaneous?flow
Relays?Output: Standard?2?relay?outputs(Optional?up?to?6?relays)
Serial?Communication: RS485,?MODBUS?-RTU?standard?protocol
Ambient?Temperature: -40 ~70 Degree C
Measure?Cycle: 1?second?(selectable?2?seconds?)
Power?Supply: DC24V?(+5%)?0.2A;?AC220V?(+20%)?0.1A?;Optional?DC12V

QT811 clamp on type ultrasonic BTU flow meter with clamp-on transducers create no wear, zero pressure loss,
and do not require process interruptions to install them since they are attached to the outside of the pipe. Clamp on BTU energy flow meter adopts a new external clamp design, which could get the flow rate without touch the measurement medium.

Pipe Size:?DN15-DN40mm (1/2¡±~1 1/2¡±)
Flow Range:¡À0.1m/s ~¡À5m/s
Temperature: 0~75¡æ (standard)
Output: 4-20mA, OCT Pulse, RS485
Accuracy:?¡À1% of measured value
Power Supply: DC10-24V

Portable clamp on ultrasonic flow meter can be easily installed, removed and transported. This flowmeter makes them ideal for industrial applications that are already operational or only require occasional flow measurement. In the latter case, the user can use the same clamp on flowmeter to measure flow in multiple locations by unloading and transporting the device for each measurement Measuring accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring clean liquids Built-in rechargeable battery 3.6V Communication: RS232

Modular type ultrasonic flow meter has very small dimension, but it’s multi-functions. It’s working with clamp type ultrasonic sensor, insertion type ultrasonic sensor or flange type sensor. It could be installed into instrument box by DIN rail.
Size: DN15-DN2000
Pipe Material: All metals, most plastics, fiber glass, etc.Allow pipe liner
Cable: Shielded transducer cable.
Power: AC: 110V/220V or DC: 8VDC-36VDC
Enclosure Protection Class: lP65
Explosive Proof Class: ExdIIBT4

Using ultrasonic transit time techniques,Wall Mounted Ultrasonic Water Flowmeter is controlled by a micro-processor system which contains a wide range of data that enables it to be used with pipes with an outside diameter ranging from 15mm up to 1200mm (depending on model) and constructed of almost any material. instrument will also operate over a wide range of fluid temperatures.

Liquid Handheld Drinking Water Ultrasonic Flowmeter measurement can be easily installed, removed and transported. This flowmeter makes them ideal for industrial applications that are already operational or only require occasional flow measurement. In the latter case, the user can use the same clamp on flowmeter to measure flow in multiple locations by unloading and transporting the device for each measurement Measuring accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring clean liquids Built-in rechargeable battery 3.6V Communication: RS232

Easy to install ultrasonic flow meter flowmeter consists of two parts: a transmitter unit and a transducer. Magnetic external clamps on the sensor are easy to install and connect to metal tubing for continuous flow measurement. It is especially suitable for on-site flow measurement of various pressure requirements. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring clean liquids Power supply: 24VDC/85VAC-2265AC Communication: RS485

Inline ultrasonic flow meter support single channel and multi-channel at the same time,when one of channel is abnormal or not connected,it can automatically switch to single channel to working
Ultrasonic flow measurement according to the ¡°differential transit time¡± method: This method uses two sensors, set opposite each other in the measuring tube. Each sensor can alternately transmit and receive ultrasonic signals, while simultaneously measuring the signal transit time.

Wall mounted inline ultrasonic flow meter is a popular solution to simplify flow measurement across a variety of applications.
Higher accuracy across a wide range of applications compared to mechanical meters.
Can be installed permanently or temporarily
Feature a streamlined design without moving parts, which results in minimal maintenance and low cost of installation and ownership.
Input:Two-wire PT1000
Output:4~20mA,Pulse,OCT,RS485
Body material:Standard carbon steel,SS304 and SS316 are optional
Power supply:DC24V and AC220V
Connection way:Flange type
Media temperature :-30~+150¡æ

Ultrasonic flow meter is suitable for continuously measuring flow and heat of clean and uniform liquids without large concentration suspended particles or gases industrial environment
Support single channel and multi-channel at the same time,when one of channel is abnormal or not connected,it can automatically switch to single channel to working .
Output:4-20mA,Pulse,OCT
Communication:RS485
Transmitter working temperature:-10~70¡æ
Sensor wotking temperature:-30~150¡æ
Power supply:DC24V,AC220V
Memory function

A handheld ultrasonic flowmeter is a low-cost portable device with a sensor for non-invasive liquid flow measurement. This handheld ultrasonic flowmeter utilizes proven time difference ultrasonic measurement technology for excellent accuracy and ease of setup and installation.
This easy-to-use flowmeter comes with a sturdy, waterproof carrying case that allows easy transport of the display, sensor, and cables between measurement locations.
Measuring accuracy: +/-1.0% of FS
Transducer temperature: -30~90¡ãC/-30¡ãC~160¡ãC
Measuring clean liquids
Battery-powered,for 12 hours
Communication: RS232

Q&T portable ultrasonic flow meters involves sending and receiving ultrasonic pulses from a pair of sensors and examining the time difference in the signal. Portable ultrasonic flow meter can be easily moved and installed in different pipes and convenient to carry site to site, which is very convenient for users to monitor the data.

Size: 1¡å~48¡å(25mm~1200mm)
Flow Range:¡À0.01 m/s~ ¡À12 m/s
Accuracy: ¡À1%
Repeatability: 0.2%
Output: 4-20mA, RS485
Power supply: Internal lithium 3000mAh
Transducer: IP68

Digital Wall Mounted Clamp on Ultrasonic Flowmeter Flow Meter is simple to install and is suitable for large diameter pipes requiring monitoring and flow measurement, as well as a wide network of smaller supply linesDigital Wall Mounted Clamp on Ultrasonic Flowmeter Flow Meter provide the tools needed to meet the diverse requirements of such a demanding industry. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring clean liquids Power supply: 24VDC/85VAC-2265AC Communication: RS485

Fixed type ultrasonic clamp on flow meter adopts the self-development measurement technology.This measurement technique is a faster and more accurate process time measurement algorithm. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring single clean liquids Power supply: 24VDC/85VAC-2265AC Communication: RS485

QT621 ultrasonic flow meter is a type of portable flow meter, main advantage is that the meter can be easily moved and installed in different pipes and convenient to carry site to site. Portable ultrasonic flow meter adopt the innovative design includes matched precision transducers
and signal processing circuitry to accurately measure the flow of most liquids over a wide range of velocities.

Size: 1¡å~48¡å(25mm~1200mm)
Flow Range:¡À0.01 m/s~ ¡À12 m/s
Accuracy: ¡À1%
Repeatability: 0.2%
Output: 4-20mA, RS485
Power supply: Internal lithium 3000mAh
Transducer: IP68

Water Ultrasonic Flow Meter Digital Clamp on transducer water flowmeter no pipe cutting required. The user simply clamp on the flow sensor to the pipe surface. Water Ultrasonic Flow Meter Digital Clamp on transducer water flowmeter can then detect the flow through ultrasonic waves, and then automatically calculate the flow rate value, flow accumulator, etc. No pipe cutting means no damage to the pipe. So as long as the pipes are in good condition, the installation on the flowmeter will not provide the possibility of leakage. Sensor: Clamp-on/External Principle: transmit time Size: DN15mm-DN6000mm Measuring medium: Liquid 3.6V Battery-powered

Modular type ultrasonic flow meter don’t need to cut off the pipeline, no pressure drop.It’s easy installation process, simply clamp the transducers on the pipe surface.It has high accuracy within ¡À1% and suitable for usage in large quantity.This type flow meter has multiple output of 4-20mA, OCT pulse and relay; RS485 interface, support Modbus protocol.
Temperature Transmitter: -20~60¡ãC;
Sensor: -30~160¡ãC
Operating conditions Humidity Transmitter: 85%RH
Sensor: can measure under water, water depth<2m Power supply: DC8~36V or AC85~264V(optional) Powerconsumption: 1.5W Dimension: 91*91*38mm (Transmitter)

This Hot sale Q&T Open Channel Flowmeter is good to measure the river flow, The meter provide 4-20mA output and RS485 serial communication (MODBUS-RTU) output; Low power consumption, easy installation; Dual power supply working, Selective use of AC / DC selective, solar energy work more energy efficient.
Display: Backlight LCD
The maximum of Accumulative Flow: 9999999.9 m3/h
Accuracy of Change in Level: 1mm or 0.2% of full span (whichever is greater)
Resolution: 1mm
Analogue Output: 4-20mA, corresponding to instantaneous?flow
Relays Output: Standard 2 relay outputs(Optional up to 6 relays)
Serial Communication: RS485, MODBUS -RTU standard protocol
Ambient Temperature: -40 ~70 Degree C
Power Supply: DC24V (+5%)?0.2A; AC220V (+20%) 0.1A ;Optional DC12V

QT811 clamp on ultrasonic flow meter is with specially design with built-in transducers and LCD monitor in one body. Clamp-on transducers are mounted externally on the surface of the pipe and which generate pulses that pass through the pipe wall. The flowing
liquid within causes time differences in the ultrasonic signals, which are then evaluated by the flowmeter to
produce an accurate flow measurement.

Pipe Size:?DN15-DN40mm (1/2¡±~1 1/2¡±)
Flow Range:¡À0.1m/s ~¡À5m/s
Temperature: 0~75¡æ (standard)
Output: 4-20mA, OCT Pulse, RS485
Accuracy:?¡À1% of measured value
Power Supply: DC10-24V

Factory supplier LCD displayer digital ultrasonic flow meter price is easy to use, fast to measure flow. It is a popular flowmeter for sewage environmental monitoring departments and large-diameter tap water flow measurement. Factory supplier LCD displayer digital ultrasonic flow meter price has the characteristics of large measurement range, and different types of sensors can be used, which can realize the measurement of pipeline flow with diameters of DN20~DN6000mm. High-precision measurement, the measurement accuracy is better than ¡À1%, the linearity is 0.5%, and the repeatability accuracy is 0.2%. Non-contact measurement The Factory supplier LCD displayer digital ultrasonic flow meter sensor is adsorbed on the outer wall of the pipe to complete the flow measurement. Measuring accuracy: +/-1.0% of FS Transducer temperature: -30~90¡ãC/-30¡ãC~160¡ãC Measuring clean liquids Built-in rechargeable battery 3.6V Communication: RS232