Digital Wall mounted clamp on ultrasonic flow meter

Clamp-on ultrasonic liquid water flow meter proven transit-time ultrasonic measurement technology This technology can be used for permanent installations where intrusive flow meters are not economically viable for permanent installations on large pipelines and for all the different process fluids encountered in the network. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring clean liquids Power supply: 24VDC/85VAC-2265AC Communication: RS485

QT621 handheld type ultrasonic water flow meter adopt transit-time principle. Portable ultrasonic flow meters are with clamp-on transducers for non-invasive liquid measurement of clean homgeneous fluids.Clamp-on transducers create no wear, zero pressure loss,
and do not require process interruptions to install them since they are attached to the outside of the pipe.

Size: 1¡å~48¡å(25mm~1200mm)
Flow Range:¡À0.01 m/s~ ¡À12 m/s
Accuracy: ¡À1%
Repeatability: 0.2%
Output: 4-20mA, RS485
Power supply: Internal lithium 3000mAh
Transducer: IP68

This Open channel flow meter require accurate measurement of the surface level of a liquid. A flume, channel or structure which has a known characteristic flow per measured head, together with the measured liquid level, accurately define the flow rate through the system.

Analogue?Output: 4-20mA,?corresponding?to?instantaneous?flow
Relays?Output: Standard?2?relay?outputs(Optional?up?to?6?relays)
Serial?Communication: RS485,?MODBUS?-RTU?standard?protocol
Ambient?Temperature: -40 ~70 Degree C
Measure?Cycle: 1?second?(selectable?2?seconds?)
Power?Supply: DC24V?(+5%)?0.2A;?AC220V?(+20%)?0.1A?;Optional?DC12V

Inline ultrasonic flow meter support single channel and multi-channel at the same time,when one of channel is abnormal or not connected,it can automatically switch to single channel to working
Ultrasonic flow measurement according to the ¡°differential transit time¡± method: This method uses two sensors, set opposite each other in the measuring tube. Each sensor can alternately transmit and receive ultrasonic signals, while simultaneously measuring the signal transit time.

Wall Mounted ultrasonic flowmeter proven transit-time ultrasonic measurement technology This technology can be used for permanent installations where intrusive flow meters are not economically viable for permanent installations on large pipelines and for all the different process fluids encountered in the network. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring clean liquids Power supply: 24VDC/85VAC-2265AC Communication: RS485

Low cost ultrasonic flow meter portable ultrasonic water sensor with high quality no pipe cutting required. The user simply clamp on the flow sensor to the pipe surface.Handheld ultrasonic flow meter transducer with RS232 communication can then detect the flow through ultrasonic waves, and then automatically calculate the flow rate value, flow accumulator, etc. No pipe cutting means no damage to the pipe. So as long as the pipes are in good condition, the installation on the flowmeter will not provide the possibility of leakage. Sensor: Clamp-on/External Principle: transmit time Size: DN15mm-DN6000mm Measuring medium: Liquid 3.6V Battery-powered

Handheld ultrasonic clamp on water flow meter flowmeter,hydraulic sewage liquid ultrasonic flow meter sensor can be easily installed, removed and transported. This flowmeter makes them ideal for industrial applications that are already operational or only require occasional flow measurement. In the latter case, the user can use the same clamp on flowmeter to measure flow in multiple locations by unloading and transporting the device for each measurement Measuring accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring clean liquids Built-in rechargeable battery 3.6V Communication: RS232

This transit-time open Channel flow meter can be used for continuous measuring of municipal rain-water, wastewater, sewage discharge and irrigation water pipelines. This Open Channel flow meter measures level, flow rate and total volume of water flowing through weirs, flumes, and channels etc.

Specifications:
Display: Backlight?LCD
Flow?Rate?Range: 0.0000~99999L/S?or?m3/h
The?maximum?of Accumulative Flow: 9999999.9?m3/h
Accuracy?of?Change in Level: 1mm?or?0.2%?of?full?span?(whichever?is?greater)
Resolution: 1mm
Analogue?Output: 4-20mA,?corresponding?to?instantaneous?flow
Relays?Output: Standard?2?relay?outputs(Optional?up?to?6?relays)
Serial?Communication: RS485,?MODBUS?-RTU?standard?protocol

Q&T solar power Open Channel flow meter measures level, flow rate and total volume of water flowing through weirs, flumes and channels. The flow meters use a non-contact level sensor. Application field£º
1. Water and sewage treatment£ºpump room, collection well, biochemical reaction
tank, sedimentation tank.
2. Electricity, mines£ºmortar pool, coal slurry pool, butter storage tank, stockyard
or some mobile equipment control, etc.
3. Food industry£ºwineries, granaries, storage tanks for food materials, etc.

Specifications:
Display: Backlight?LCD
The?maximum?of Accumulative Flow: 9999999.9?m3/h
Resolution: 1mm
Analogue?Output: 4-20mA
Relays?Output: Standard?2?relay?outputs(Optional?up?to?6?relays)
Serial?Communication: RS485,?MODBUS RTU
Ambient?Temperature: -40 ~70 Degree C
Power?Supply: DC24V, AC 220V£»Optional?DC12V

Perfect Quality Economical Ultrasonic Flow meter insertion type ultrasonic flowmeter is a high precision no-cut tube measurement method. This special design includes matching sensors for ease of use and is ideal for installation in existing systems Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring single clean liquids Power supply: 24VDC/85VAC-2265AC Storage: SD card optional Heat meter optional

Digital ultrasonic flow meter also adopt time-transit technology,enjoy higher accuracy and better stability compare with 1st generation ultrasonic flow meter,with 4-20mA,relay output. Communication: RS232/RS485 Mod bus:
Power supply:10~36VDC/1A;
Display:240*128 back lit LCD;
Temperature:Transmitter: -14℉~140℉(-20℃~60℃),Transducer: -40℉~176℉(-40℃~80℃,standard); Humidity:Up to 99% RH, non-condensing;

Modular type ultrasonic flow meter don’t need to cut off the pipeline, no pressure drop.It’s easy installation process, simply clamp the transducers on the pipe surface.It has high accuracy within ¡À1% and suitable for usage in large quantity.This type flow meter has multiple output of 4-20mA, OCT pulse and relay; RS485 interface, support Modbus protocol.
Temperature Transmitter: -20~60¡ãC;
Sensor: -30~160¡ãC
Operating conditions Humidity Transmitter: 85%RH
Sensor: can measure under water, water depth<2m Power supply: DC8~36V or AC85~264V(optional) Powerconsumption: 1.5W Dimension: 91*91*38mm (Transmitter)

Ultrasonic Flow meter handheld clamp on flowmeter no pipe cutting required. The user simply clamp on the flow sensor to the pipe surface. Ultrasonic Flow meter handheld clamp on flowmeter can then detect the flow through ultrasonic waves, and then automatically calculate the flow rate value, flow accumulator, etc. No pipe cutting means no damage to the pipe. So as long as the pipes are in good condition, the installation on the flowmeter will not provide the possibility of leakage. Sensor: Clamp-on/External Principle: transmit time Size: DN15mm-DN6000mm Measuring medium: Liquid 3.6V Battery-powered

QT621 portable type ultrasonic clamp on flow meters support quickly verify the reading of another meter and to data log flow system values over an extended time period.
Portable ultrasonic flow meters can be easily moved and installed in different pipes and convenient to carry site to site, which is very convenient for users to monitor the data.

Size: 1¡å~48¡å(25mm~1200mm)
Flow Range:¡À0.01 m/s~ ¡À12 m/s
Accuracy: ¡À1%
Repeatability: 0.2%
Output: 4-20mA, RS485
Power supply: Internal lithium 3000mAh
Transducer: IP68

Handheld Ultrasonic Water Flowmeter Clamp on Flow meter is easy and accurate flow measurement without interrupting the process, Clamp-on type transducer easily mountable on existing pipes, non-invasive type.Suitable for most of applications. Measuring accuracy: +/-1.0% of FS Transducer temperature: -30~90¡ãC/-30¡ãC~160¡ãC Measuring clean liquids Built-in rechargeable battery 3.6V Communication: RS232

Not affected by water quality, the ultrasonic open channel flowmeter can be equipped with a communication interface, which is easy to connect with SCADA systems to achieve industrial remote monitoring and control. This Open Channel flow meter measures level, flow rate and total volume of water flowing through weirs, flumes, and channels etc.

Specifications:
Sensor?Level?Range: 0-4.0m; other?level?range?also?available
Blind?zone: 0.20m
Temperature?Compensation: Integral?in?probe
Pressure?Rating: 0.2MPa
Beam?Angle: 8*?(3db)
Cable?Length: 10m?standard?(can?be?extended?to?1000m)
Sensor?Material: ABS,?PVC?or?PTFE?(optional)
Sensor?Protection Class: IP68

Modular type ultrasonic flow meter is one type of ultrasonic flow meter.It has very small size and easy to be installed into instrument box. This type flow is working with clamp type transducer normally. The max measure tube is DN3000 pipe. It have 4-02mA, pulse, and RS485 output also.It even could link with temperature sensor and work as ultrasonic BTU meter.
Accuracy: ±1%
Velocity: 0.5s
Display: LCD with backlight 2*20leters
Signal Outputs: 4-20mA or o-20mA,RS485,Pulse
Liquid Types: Virtually all commonly used liquids
Pipe Size: DN15-DN3000

QT811 clamp on ultrasonic flow meter is a type of non-invasive flowmeters work on the transit time ultrasonic principle. This involves sending and receiving ultrasonic pulses from a pair of sensors and examining the time difference in the signal. Suitable for various liquids and compatible with various pipeline materials and sizes.

Pipe Size:?DN15-DN40mm (1/2¡±~1 1/2¡±)
Flow Range:¡À0.1m/s ~¡À5m/s
Temperature: 0~75¡æ (standard)
Output: 4-20mA, OCT Pulse, RS485
Accuracy:?¡À1% of measured value
Power Supply: DC10-24V

Ultrasonic flowmeters use sound waves to determine the velocity of a fluid flowing in a pipe.
Inline type ultrasonic flow meter can be OEM,such as Body color,Transmitter color,Channle number,Logo display etc.
Q&T brand ultrasonic flow meter is one kind of economy type flow meter for liquid,multi channle inline ultrasonic flow meter can reach 0.5% accuracy

Widely used in Running water,Heating, Water conservation,Metallurgy,Chemical industry,Machinery,Energy etc.

Low cost ultrasonic flow meter has the high-speed data update rate and superior user-friendliness in installation and operation.Economic ultrasonic flow meter without pressure drop or energy loss. Humidity:Up to 99% RH, non-condensing;
Transmitter material: PC/ABS, IP65;
Transducer:ABS,IP68
Accuracy:±1% of measured value;
Repeatability:0.2% of measured value;

China portable water flow sensor handheld ultrasonic flow meter is a non-contact instrument, which can measure the flow of medium with large diameter and can also be used for the measurement of medium that is not easy to contact and observe. Its measurement accuracy is very high, and the external clip-type installation can reach the highest accuracy of ¡À1.0%. It is almost not disturbed by various parameters of the measured medium, especially it can solve the strong corrosiveness, non-conductivity, Flow measurement of radioactive and flammable and explosive media Measuring accuracy: +/-1.0% of FS Transducer temperature: -30~90¡ãC/-30¡ãC~160¡ãC Measuring clean liquids Battery-powered,for 12 hours Communication: RS232

Not affected by water quality, the solar power ultrasonic open channel flowmeter can be equipped with a communication interface, which is easy to connect with SCADA systems to achieve industrial remote monitoring and control. This Open Channel flow meter measures level, flow rate and total volume of water flowing through weirs, flumes, and channels etc.

Specifications:
Sensor?Level?Range: 0-4.0m; other?level?range?also?available
Blind?zone: 0.20m
Temperature?Compensation: Integral?in?probe
Pressure?Rating: 0.2MPa
Beam?Angle: 8*?(3db)
Cable?Length: 10m?standard?(can?be?extended?to?1000m)
Sensor?Material: ABS,?PVC?or?PTFE?(optional)
Sensor?Protection Class: IP68

PLCM open channel meter is good for Flow Measurement in Open Channel,river; it is a high quality water flow meters, RS485 River Flow Meter; This ultrasonic open channel flow meter is Suitable for a variety of weirs and flumes, Parshall flumes (ISO), V-Notch weirs, Rectangular weirs(With or Without End Contractions) and custom Formula type weir; LCD display with backlight
Accuracy of Change in Level: 1mm or 0.2% of full span (whichever is greater)
Resolution: 1mm
Analogue Output: 4-20mA, corresponding to instantaneous flow
Relays Output: Standard 2 relay outputs(Optional up to 6 relays)
Serial Communication: RS485, MODBUS -RTU standard protocol
Ambient Temperature: -40 ~70 Degree C
Measure Cycle: 1 second (selectable 2 seconds )
Power Supply: DC24V (+5%) 0.2A; AC220V (+20%) 0.1A ;Optional DC12V

Precise digital display insertion clamp on ultrasonic water flow meter Wall mounted ultrasonic flowmeter is simple to install and is suitable for large diameter pipes requiring monitoring and flow measurement, as well as a wide network of smaller supply lines.Precise digital display insertion clamp on ultrasonic water flow meter Wall mounted ultrasonic flowmeter provide the tools needed to meet the diverse requirements of such a demanding industry. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring clean liquids Power supply: 24VDC/85VAC-2265AC Communication: RS485

QT811 ultrasonic flow meter is specially designed for small pipe sizes clamp on flow measurements. It is integrated design with the monitor LCD and the sensors in one body, user could read flow rate directly from the device. With various kinds of outputs including 4-20mA, OCT pulse and RS485 modbus, ultrasonic flow meter could achieve remote monitoring in central control room.

Pipe Size:?DN15-DN40mm (1/2¡±~1 1/2¡±)
Flow Range:¡À0.1m/s ~¡À5m/s
Temperature: 0~75¡æ (standard)
Output: 4-20mA, OCT Pulse, RS485
Accuracy:?¡À1% of measured value
Power Supply: DC10-24V

Measuring Pipe Size DN15-DN6000 Wall Water Mounted Ultrasonic Flow Meter is a high precision no-cut tube measurement method. This special design includes matching sensors for ease of use and is ideal for installation in existing systems Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring single clean liquids Power supply: 24VDC/85VAC-2265AC Storage: SD card optional Heat meter optional

Q&T Handheld ultrasonic flowmeter measure flow rate by propagating ultrasound waves into liquid-filled pipes and measuring the flow. With transit time, these clamp-on ultrasonic meters are outside the pipe, providing a wide range of pipe sizes, no pressure loss, none contact with internal liquid and no moving parts.
Measuring accuracy: +/-1.0% of FS
Wide range: DN15mm-DN6000mm
Measuring clean liquids
Built-in rechargeable battery 3.6V
Communication: RS232

clamp on ultrasonic portable liquid flow meter is controlled by a micro-processor system which contains a wide range of data that enables it to be used with pipes with an outside diameter ranging from 15mm up to 1200mm (depending on model) and constructed of almost any material. instrument will also operate over a wide range of fluid temperatures.

QT811 external clamp on type ultrasonic energy meters uses clamp-on transducers that are mounted externally on the surface of the pipe and which generate pulses that pass through the pipe wall.
Specially external clamp design, QT811 clamp on ultrasonic energy BTU meter could achieve flow measurement without touch the measurement liquid.

Pipe Size:?DN15-DN40mm (1/2¡±~1 1/2¡±)
Flow Range:¡À0.1m/s ~¡À5m/s
Temperature: 0~75¡æ (standard)
Output: 4-20mA, OCT Pulse, RS485
Accuracy:?¡À1% of measured value
Power Supply: DC10-24V