Digital Ultrasonic Water Flowmeter Wall Mounted Relay alarm and RS485 Modbus flow meters

This open channel ultrasonic flowmeter is low cost compared with other type open channel flow meter, we are the professional manufacturer of ultrasonic open channel flow meter from China.
And with non-contact type sensor, the meter has a higher reliability than other forms of the instrument, when under the dirt, corrosive liquids case.
Display: Backlight LCD
The maximum of Accumulative Flow: 9999999.9 m3/h
Accuracy of Change in Level: 1mm or 0.2% of full span (whichever is greater)
Resolution: 1mm
Analogue Output: 4-20mA, corresponding to instantaneous flow
Relays Output: Standard 2 relay outputs(Optional up to 6 relays)
Serial Communication: RS485, MODBUS -RTU standard protocol
Ambient Temperature: -40 ~70 Degree C
Power Supply: DC24V (+5%) 0.2A; AC220V (+20%) 0.1A ;Optional DC12V

Transit Time Ultrasonic can work alone without a LCD andKeypad module,the module can be used alone as a flow meter.Users caneven integrate a number of the modules into a multi-channel flow meter thatcan measures up to several dozen of different pipes or a flow meter that has higher accuracy by measures the same pipe with all the channels.
Pipe material: Steel, stainless steel, cast iron, copper, cement, PVC, aluminum, glass fiber reinforced plastics, pipes with liner also work
Pipe diameter: 15~6000mm
StraightpipeInstallation condition: upstream10D, downstream 5D, 30D from the pump
Medium Liquid type: Single liquid that could transmit sound wave,
Sewage with small particle content;
Chemicals (alcohol, etc. ) Plant effluent; Beverage;
Ultra-pure liquids, etc.
Temperature: -30~160¡ãC
Turbidity: Not more than 10000ppm, few bubble
Flow rate: 0~¡À7m/s

Digital Ultrasonic flowmeter river water type ultrasonic flowmeter is a high precision no-cut tube measurement method. This special design includes matching sensors for ease of use and is ideal for installation in existing systems Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring single clean liquids Power supply: 24VDC/85VAC-2265AC Storage: SD card optional Heat meter optional

wall-mounted digital display industrial ultrasonic flow meter sea water ultrasonic flowmeter consists of two parts: a transmitter unit and a transducer. Magnetic external clamps on the sensor are easy to install and connect to metal tubing for continuous flow measurement. It is especially suitable for on-site flow measurement of various pressure requirements. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring clean liquids Power supply: 24VDC/85VAC-2265AC Communication: RS485

Ultrasonic Water Flow Meter DN50-DN400 Sewage Water Ultrasonic Flow Meter is a portable liquid flow measurement device with a sensor. Hot sales portable ultrasonic flowmeter handheld water flow meter adopt transit-time ultrasonic measurement technology for superior accuracy and ease of installation and installation. This easy-to-use flowmeter comes in a rugged, waterproof carrying case for easy transport of the display, sensor, and cables between measurement locations. High accuracy +/-1.0% of FS Transducer temperature: -30~90¡ãC/-30¡ãC~160¡ãC Measuring clean liquids Battery-powered,for 12 hours Communication: RS232

OEM factory price OEM wall mount Clamp on ultrasonic flow meter Used for production monitoring, water balance testing, thermal equilibrium network commissioning, energy monitoring.

Using ultrasonic transit time techniques,Wall Mounted Ultrasonic Water Flowmeter is controlled by a micro-processor system which contains a wide range of data that enables it to be used with pipes with an outside diameter ranging from 15mm up to 1200mm (depending on model) and constructed of almost any material. instrument will also operate over a wide range of fluid temperatures.

QTDS-100H Handheld ultrasonic Flowmeter Portable Water Flow meter use ultrasonic technology to measure the velocity of the liquid. Ultrasonic meters are avaiable as clamp-on solutions. Non pipe cutting, this ultrasonic flow meters can display velocity and accumulated flow. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Medium: clean liquids,pure water Built-in rechargeable battery 3.6V Housing Material: ABS

Q&T brand pulse output ultrasonic flow meter is one kind of economy type flow meter for liquid,multi channle inline ultrasonic flow meter accuracy less 0.5%
OCT output
RS485 communication
Input:Two-wire PT1000

The majority of wall mount ultrasonic flow meter applied in general industry.liquid ultrasonic flow meter is suitable for measuring variety of different liquids.
Humidity:Up to 99% RH, non-condensing;
Transmitter material: PC/ABS, IP65;
Transducer:ABS,IP68
Accuracy:±1% of measured value;
Repeatability:0.2% of measured value;

Pipeline ultraosnic flow meter is one kind flow meter which directly contact the liquid and make the measuring accuracy better than clamp on ultrasonic flowmeter and mainly applications in clean water and in low conductivity media. Operating principle based on transit time measurement.
Output:4-20mA,Pulse,OCT
Communication:RS485
Transmitter working temperature:-10~70¡æ
Sensor wotking temperature:-30~150¡æ
Power supply:DC24V,AC220V

Digital ultrasonic flow meter also adopt time-transit technology,enjoy higher accuracy and better stability compare with 1st generation ultrasonic flow meter,with 4-20mA,relay output. Communication: RS232/RS485 Mod bus:
Power supply:10~36VDC/1A;
Display:240*128 back lit LCD;
Temperature:Transmitter: -14℉~140℉(-20℃~60℃),Transducer: -40℉~176℉(-40℃~80℃,standard); Humidity:Up to 99% RH, non-condensing;

Portable Hand Held Ultrasonic Flow Meter are widely used in tap water, heating, water conservancy, metallurgy, chemical industry, machinery, energy and other industries. Portable Hand Held Ultrasonic Flow Meter can be used for production monitoring, flow verification, temporary detection, flow inspection, water meter balance debugging, heat network balance debugging, and energy-saving monitoring. Measuring accuracy: +/-1.0% of FS Transducer temperature: -30~90¡ãC/-30¡ãC~160¡ãC Measuring clean liquids Battery-powered,for 12 hours Communication: RS232

QTDS-100H handheld liquid ultrasonic flow meter China supplier is a portable liquid flow measurement device with a sensor. QTDS-100H handheld liquid ultrasonic flow meter China supplier proven transit-time ultrasonic measurement technology for superior accuracy and ease of installation and installation. This easy-to-use flowmeter comes in a rugged, waterproof carrying case for easy transport of the display, sensor, and cables between measurement locations. High accuracy +/-1.0% of FS Transducer temperature: -30~90¡ãC/-30¡ãC~160¡ãC Measuring clean liquids Battery-powered,for 12 hours Communication: RS232

Clamp on ultrasonic flow meter equipment installation, no pipe cutting required. This is very different from traditional flow devices. The user simply clamp on the flow sensor to the pipe surface. The ultrasonic flowmeter can then detect the flow through ultrasonic waves, and then automatically calculate the flow rate value, flow accumulator, etc. No pipe cutting means no damage to the pipe. So as long as the pipes are in good condition, the installation on the flowmeter will not provide the possibility of leakage. This advantage is more suitable for strong acid, strong alkali, poisoning, corrosive liquid, etc. Sensor: Clamp-on/External Principle: transmit time Size: DN15mm-DN6000mm Measuring medium: Liquid 3.6V Battery-powered

QT621 battery powered ultrasonic clamp on flow meters are widely used from simple water flow
measurements to energy flow monitoring and automated process control.
Portable ultrasonic flow meters are with various kinds of output signals, including, 4-20mA analog and RS485 modbus which is very common and convenient for onsite monitoring.

Size: 1¡å~48¡å(25mm~1200mm)
Flow Range:¡À0.01 m/s~ ¡À12 m/s
Accuracy: ¡À1%
Repeatability: 0.2%
Output: 4-20mA, RS485
Power supply: Internal lithium 3000mAh
Transducer: IP68

Ultrasonic Flow meter for applications in clean water and in low conductivity media. Operating principle based on transit time measurement.
Pipe material:Steel,Stainless steel,Cast iron,PVC,Cement pipe and allow pipe with lining
High Isolation voltage,Strong anti-interference,Suppress voltage noise,Good isolation performance
Inline ultrasonic flow meter collect temperature signal and accuracy reach 0.001¡æ
Viscosity:0.1~10m/s
Measuring cycle:50mS
Output:4~20mA,Pulse,OCT,RS485
Body material:Standard carbon steel,SS304 and SS316 are optional
Power supply:DC24V and AC220V

This non-contact solar power ultrasonic flow meter that is designed for open channel flow metering working with a flume, weir or any other primary device. Non-contact ultrasonic flow meter require accurate measurement of the surface level of a liquid. A flume, channel or structure which has a known characteristic flow per measured head, together with the measured liquid level, accurately define the flow rate through the system.

Analogue?Output: 4-20mA,?corresponding?to?instantaneous?flow
Relays?Output: Standard?2?relay?outputs(Optional?up?to?6?relays)
Serial?Communication: RS485,?MODBUS?-RTU?standard?protocol
Ambient?Temperature: -40 ~70 Degree C
Measure?Cycle: 1?second?(selectable?2?seconds?)
Power?Supply: DC24V?(+5%)?0.2A;?AC220V?(+20%)?0.1A?;Optional?DC12V

Cheap low cost hydraulic digital ultrasonic sewage water sensor liquid flow meter consists of two parts: a transmitter unit and a transducer. Magnetic external clamps on the sensor are easy to install and connect to metal tubing for continuous flow measurement. It is especially suitable for on-site flow measurement of various pressure requirements. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring clean liquids Power supply: 24VDC/85VAC-2265AC Communication: RS485

Ultrasonic flowmeters use sound waves to determine the velocity of a fluid flowing in a pipe.
Inline type ultrasonic flow meter can be OEM,such as Body color,Transmitter color,Channle number,Logo display etc.
Q&T brand ultrasonic flow meter is one kind of economy type flow meter for liquid,multi channle inline ultrasonic flow meter can reach 0.5% accuracy.

China wall-mounted ultrasonic water flow meter price is an ultrasonic flowmeter used to measure the flow rate of liquids in closed pipes. The transducer is clamp-on type, which will provide the benefits of contamination-free operation and ease of installation. The transit time flowmeter includes two transducers, which act as ultrasonic transmitters and receivers. The transducer can be installed in a v-type method, where the sound travels through the pipe twice, a w-type method, where the sound travels through the pipe four times. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring clean liquids Power supply: 24VDC/85VAC-2265AC Communication: RS485

QT811 clamp on BTU energy flow meter are popular in water treatment, pure water, chemical and etc. Clamp on type flow meter specially designed for small sizes DN15-DN40mm. As a type of small instrument, QT811 clamp on flow meter support quick flow and energy measurement for many types of pipings.

Pipe Size:?DN15-DN40mm (1/2¡±~1 1/2¡±)
Flow Range:¡À0.1m/s ~¡À5m/s
Temperature: 0~75¡æ (standard)
Output: 4-20mA, OCT Pulse, RS485
Accuracy:?¡À1% of measured value
Power Supply: DC10-24V

Pulse output wall-mount ultrasonic flow meter add one pair PT1000 temperature sensor to realize heat/cold measurement,clamp-on ultrasonic meter also called as ultrasonic BTU meter. Accuracy:±1% of measured value;
Repeatability:0.2% of measured value;
Linearity:±1%;
Pipe size:1″ to 48″ (25mm to 1200mm).Pipe size under 1″ is an option;
Fluid:Water or others;

Precise digital display insertion clamp on ultrasonic water flow meter Wall mounted ultrasonic flowmeter is simple to install and is suitable for large diameter pipes requiring monitoring and flow measurement, as well as a wide network of smaller supply lines.Precise digital display insertion clamp on ultrasonic water flow meter Wall mounted ultrasonic flowmeter provide the tools needed to meet the diverse requirements of such a demanding industry. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring clean liquids Power supply: 24VDC/85VAC-2265AC Communication: RS485

Wastewater ultrasonic flow meter sensor for liquid are widely used in tap water, heating, water conservancy, metallurgy, chemical industry, machinery, energy and other industries. Wastewater ultrasonic flow meter sensor for liquid can be used for production monitoring, flow verification, temporary detection, flow inspection, water meter balance debugging, heat network balance debugging, and energy-saving monitoring. Measuring accuracy: +/-1.0% of FS Transducer temperature: -30~90¡ãC/-30¡ãC~160¡ãC Measuring clean liquids Battery-powered,for 12 hours Communication: RS232

QT621 Portable ultrasonic flow meter support configurable for flow and thermal energy measurement. Portable ultrasonic water flow meter mainly consists of two parts, transmitter and transducer. With 4-20mA and RS485 communication available, QT621 ultrasonic flow meter support quickly verify the flow reading of another meter and to data log flow system values over an extended time period.

Size: 1¡å~48¡å(25mm~1200mm)
Flow Range:¡À0.01 m/s~ ¡À12 m/s
Accuracy: ¡À1%
Repeatability: 0.2%
Output: 4-20mA, RS485
Power supply: Internal lithium 3000mAh
Transducer: IP68

Ultrasonic flowmeters use sound waves to determine the velocity of a fluid flowing in a pipe.
Inline type ultrasonic flow meter can be OEM,such as Body color,Transmitter color,Channle number,Logo display etc.
Q&T brand ultrasonic flow meter is one kind of economy type flow meter for liquid,multi channle inline ultrasonic flow meter can reach 0.5% accuracy.
Measuring cycle:50mS
Output:4~20mA,Pulse,OCT,RS485
Body material:Standard carbon steel,SS304 and SS316 are optional
Power supply:DC24V and AC220V

Handheld ultrasonic water flowmeter for liquid is mainly divided into ultrasonic flow unit, flow transducer and information processing circuit, flow display. First, the ultrasonic signal generator is used to send the signal, the sensor receives the signal, and the time difference is obtained. The ultrasonic information is processed according to the information processing circuit, and the flow is transmitted to the display screen in the form of an electrical signal, and the result is displayed Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Medium: clean liquids,pure water Built-in rechargeable battery 3.6V Measurment unit: Meter, Feet,Cubic Meter.

LCD display Clamp on Portable ultrasonic flowmeter is a wide used time difference ultrasonic flowmeter. It is small and light, the installation process is extremely simply and easy to operate. The design of rechargeable battery and universal power supply enables you to realize pipeline measurement anytime and anywhere.
The portable ultrasonic flowmeter consists of two parts: transmitter unit and transducer. The magnetic external clamp on transducer is easy to insntall and can be attached to a metal pipe for continuous flow measurement. It is especially suitable for on-site flow measurement with various pressure requirements.
Measuring accuracy: +/-1.0% of FS
Transducer temperature: -30~90¡ãC/-30¡ãC~160¡ãC
Measuring clean liquids
Battery-powered,for 12 hours
Communication: RS232

QT621 portable type ultrasonic flow meter is widely applied in oil industry, water treatment, pure water, chemical and etc.
Portable ultrasonic flow meter transmitter configurable for flow and thermal energy measurement. QT621 portable ultrasonic flow meter support quickly verify the flow reading of another meter and to data log flow system values over an extended time period.

Size: 1¡å~48¡å(25mm~1200mm)
Flow Range:¡À0.01 m/s~ ¡À12 m/s
Accuracy: ¡À1%
Repeatability: 0.2%
Output: 4-20mA, RS485
Power supply: Internal lithium 3000mAh
Transducer: IP68