Clamp on ultrasonic flow meter

Handheld Digital Clamp Ultrasonic flow meter, ultrsonic flow meter is a ideal for liquids such as chemical,visous liquids, and sea water. The non-intrusive, clamp-on ultrasonic flow meter fits pipes between 1/2″ to 48″ internal diameter. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Medium: clean liquids,pure water Built-in rechargeable battery 3.6V Measurment unit: Meter, Feet,Cubic Meter.

Handheld ultrasonic flow meter with clamp on Middle transducer is easy and accurate flow measurement without interrupting the process, Clamp-on type transducer easily mountable on existing pipes, non-invasive type.Suitable for most of applications. Measuring accuracy: +/-1.0% of FS Transducer temperature: -30~90¡ãC/-30¡ãC~160¡ãC Measuring clean liquids Built-in rechargeable battery 3.6V Communication: RS232

RS232 3.6V Lithium Battery Digital Water Handheld Ultrasonic Flow Meter is a non-contact instrument, which can measure the flow of medium with large diameter and can also be used for the measurement of medium that is not easy to contact and observe. Digital Water Handheld Ultrasonic Flow Meter measurement accuracy is very high, and it is hardly disturbed by various parameters of the measured medium.
Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Medium: clean liquids,pure water Built-in rechargeable battery 3.6V Communication: RS232

Factory Ultrasonic Flow Meters water flow sensor is a non-contact instrument, which can measure the flow of medium with large diameter and can also be used for the measurement of medium that is not easy to contact and observe. Its measurement accuracy is very high, and the external clip-type installation can reach the highest accuracy of ¡À1.0%. It is almost not disturbed by various parameters of the measured medium, especially it can solve the strong corrosiveness, non-conductivity, Flow measurement of radioactive and flammable and explosive media Measuring accuracy: +/-1.0% of FS Transducer temperature: -30~90¡ãC/-30¡ãC~160¡ãC Measuring clean liquids Battery-powered,for 12 hours Communication: RS232

PLCM series ultrasonic open channel flow meter is a low cost choice. It is a hot sell product for river channel measuring. The product supports weirs or notches of different standards in various countries and can be widely used for measurement or monitoring of total water drainage.
Display: Backlight LCD
The maximum of Accumulative Flow: 9999999.9 m3/h
Accuracy of Change in Level: 1mm or 0.2% of full span (whichever is greater)
Resolution: 1mm
Analogue Output: 4-20mA, corresponding to instantaneous flow
Relays Output: Standard 2 relay outputs(Optional up to 6 relays)
Serial Communication: RS485, MODBUS -RTU standard protocol
Ambient Temperature: -40 ~70 Degree C
Power Supply: DC24V (+5%) 0.2A; AC220V (+20%) 0.1A ;Optional DC12V

QT621 Portable ultrasonic flow meter support configurable for flow and thermal energy measurement. Portable ultrasonic water flow meter mainly consists of two parts, transmitter and transducer. With 4-20mA and RS485 communication available, QT621 ultrasonic flow meter support quickly verify the flow reading of another meter and to data log flow system values over an extended time period.

Size: 1¡å~48¡å(25mm~1200mm)
Flow Range:¡À0.01 m/s~ ¡À12 m/s
Accuracy: ¡À1%
Repeatability: 0.2%
Output: 4-20mA, RS485
Power supply: Internal lithium 3000mAh
Transducer: IP68

QT621 battery powered ultrasonic clamp on flow meters are widely used from simple water flow
measurements to energy flow monitoring and automated process control.
Portable ultrasonic flow meters are with various kinds of output signals, including, 4-20mA analog and RS485 modbus which is very common and convenient for onsite monitoring.

Size: 1¡å~48¡å(25mm~1200mm)
Flow Range:¡À0.01 m/s~ ¡À12 m/s
Accuracy: ¡À1%
Repeatability: 0.2%
Output: 4-20mA, RS485
Power supply: Internal lithium 3000mAh
Transducer: IP68

This Open Channel Water Meters can be widely applied to the environmental protection, water treatment, irrigation, chemical, and other industries. Sewage and rainwater are often transported to the treatment plant in open collection channels or flumes. The flow rate is measured at various points in these channels, and our open channel flow meters are the good choice for these applications.

Specifications:
Display: Backlight?LCD
Flow?Rate?Range: 0.0000~99999L/S?or?m3/h
The?maximum?of Accumulative Flow: 9999999.9?m3/h
Accuracy?of?Change in Level: 1mm?or?0.2%?of?full?span?(whichever?is?greater)
Resolution: 1mm
Analogue?Output: 4-20mA,?corresponding?to?instantaneous?flow
Relays?Output: Standard?2?relay?outputs(Optional?up?to?6?relays)
Serial?Communication: RS485,?MODBUS?-RTU?standard?protocol

Handheld Ultrasonic Flow Meter(QTDS-100H)- Wide range of applications,with clamp on transducers to measure flow rate through the pipe wall, the transit time ultrasonic flow principle. It is a 3.6V battery powered ultrsonic flow meter, for using on a wide range of sizes and can provide 24 hours measurement continuely. Accuracy: +/-1.0% of FS Wide range: DN300mm-DN6000mm Measuring clean liquids Built-in rechargeable battery 3.6V 2000 lines storage Communication: RS232

QT621 portable type ultrasonic clamp on flow meters support quickly verify the reading of another meter and to data log flow system values over an extended time period.
Portable ultrasonic flow meters can be easily moved and installed in different pipes and convenient to carry site to site, which is very convenient for users to monitor the data.

Size: 1¡å~48¡å(25mm~1200mm)
Flow Range:¡À0.01 m/s~ ¡À12 m/s
Accuracy: ¡À1%
Repeatability: 0.2%
Output: 4-20mA, RS485
Power supply: Internal lithium 3000mAh
Transducer: IP68

Pipeline ultraosnic flow meter directly contact the liquid and make the measuring accuracy better than clamp on ultrasonic flowmeter.And installation easy,don’t need calculate the sensor installation distance and cover the coupling agent in the pipe,so this meter can collect the signal very well.
Szie:DN15~DN6000
Accuracy:¡À1.0 %
Viscosity:0.1~10m/s
Measuring cycle:50mS

QT621 ultraonic flow meter portable type is an easy operation instrument for non-invasive, quick flow and energy measurement with clamp-on technology for many types of pipings.
Portable ultrasonic flow meter can be easily moved and installed in different pipes and convenient to carry site to site, which is very convenient for users to monitor the data.

Size: 1¡å~48¡å(25mm~1200mm)
Flow Range:¡À0.01 m/s~ ¡À12 m/s
Accuracy: ¡À1%
Repeatability: 0.2%
Output: 4-20mA, RS485
Power supply: Internal lithium 3000mAh
Transducer: IP68

According to market request,the power supply can 24VDC or 220VAC or solar powered;Current the solar powered ultrasonic flow meter is more popular,beacuse solar powered meets international requirements, energy saving and environmental protection.
Accuracy:±1.0%
Heat measurement
Carbon steel body

The fluid can smothly through the inline ultrasonic flow sensors which no moving pasts,No wear,No pressure loss and Maintenance free.
Pipeline ultraosnic flow meter directly contact the liquid and make the measuring accuracy better than clamp on ultrasonic flowmeter.And installation easy,don’t need calculate the sensor installation distance and cover the coupling agent in the pipe,so this meter can collect the signal very well.
Power supply:DC24V and AC220V
Connection way:Flange type
Media temperature :-30~+150¡æ

QT811 DN15-40mm clamp on flow meter is a new designed external clamp on measurement flow meter. Clamp on ultrasonic flow meter adopt non-invasive flow measurements, This involves sending and receiving ultrasonic pulses from a pair of sensors and examining the time difference in the signal. Clamp on flow meter support monitor the flow rate reading directly on the device.

Pipe Size:?DN15-DN40mm (1/2¡±~1 1/2¡±)
Flow Range:¡À0.1m/s ~¡À5m/s
Temperature: 0~75¡æ (standard)
Output: 4-20mA, OCT Pulse, RS485
Accuracy:?¡À1% of measured value
Power Supply: DC10-24V

0.5% accuracy ultraosnic flow meter with multi channel sensor and body mainly be adopted carbon steel material ,can produce stainless stell according to request.
Instantaneous flow,Total flow,Heat,Positive flow,Negative flow
High Isolation voltage,Strong anti-interference,Suppress voltage noise,Good isolation performance
Inline ultrasonic flow meter collect temperature signal and accuracy reach 0.001¡æ
When using inline ultrasonic flow meter to measure,allowing pipe with liner

clamp on ultrasonic portable liquid flow meter is controlled by a micro-processor system which contains a wide range of data that enables it to be used with pipes with an outside diameter ranging from 15mm up to 1200mm (depending on model) and constructed of almost any material. instrument will also operate over a wide range of fluid temperatures.

Strap on ultrasonic flow meter enjoy ±1.0% accuracy in real application,300times/second high responsive speed,Q&T water liquid ultrasonic flow meter could measure 0.03m/s low flow velocity. Accuracy:±1% of measured value;
Temperature:Transmitter: -14℉~140℉(-20℃~60℃),Transducer: -40℉~176℉(-40℃~80℃,standard); Humidity:Up to 99% RH, non-condensing;
Transmitter material:PC/ABS,IP65;
Transducer:ABS,IP68

Ultrasonic flow measurement according to the ¡°differential transit time¡± method: This method uses two sensors, set opposite each other in the measuring tube. Each sensor can alternately transmit and receive ultrasonic signals, while simultaneously measuring the signal transit time.
Measuring cycle:50mS
Output:4~20mA,Pulse,OCT,RS485
Body material:Standard carbon steel,SS304 and SS316 are optional
Power supply:DC24V and AC220V

Factory supplier LCD displayer digital ultrasonic flow meter price is easy to use, fast to measure flow. It is a popular flowmeter for sewage environmental monitoring departments and large-diameter tap water flow measurement. Factory supplier LCD displayer digital ultrasonic flow meter price has the characteristics of large measurement range, and different types of sensors can be used, which can realize the measurement of pipeline flow with diameters of DN20~DN6000mm. High-precision measurement, the measurement accuracy is better than ¡À1%, the linearity is 0.5%, and the repeatability accuracy is 0.2%. Non-contact measurement The Factory supplier LCD displayer digital ultrasonic flow meter sensor is adsorbed on the outer wall of the pipe to complete the flow measurement. Measuring accuracy: +/-1.0% of FS Transducer temperature: -30~90¡ãC/-30¡ãC~160¡ãC Measuring clean liquids Built-in rechargeable battery 3.6V Communication: RS232

RS485 Modbus Digital Ultrasonic Fluid Flow Meter DN100 Wall Mounting Ultrasonic Flowmeter is simple to install and is suitable for large diameter pipes requiring monitoring and flow measurement, as well as a wide network of smaller supply lines.RS485 Modbus Digital Ultrasonic Fluid Flow Meter DN100 Wall Mounting Ultrasonic Flowmeter provide the tools needed to meet the diverse requirements of such a demanding industry. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring clean liquids Power supply: 24VDC/85VAC-2265AC Communication: RS485

This non-contact ultrasonic flow meter that is designed for open channel flow metering working with a flume, weir or any other primary device. Non-contact ultrasonic flow meter require accurate measurement of the surface level of a liquid. A flume, channel or structure which has a known characteristic flow per measured head, together with the measured liquid level, accurately define the flow rate through the system.

Analogue?Output: 4-20mA,?corresponding?to?instantaneous?flow
Relays?Output: Standard?2?relay?outputs(Optional?up?to?6?relays)
Serial?Communication: RS485,?MODBUS?-RTU?standard?protocol
Ambient?Temperature: -40 ~70 Degree C
Measure?Cycle: 1?second?(selectable?2?seconds?)
Power?Supply: DC24V?(+5%)?0.2A;?AC220V?(+20%)?0.1A?;Optional?DC12V

Easy to install ultrasonic flow meter flowmeter consists of two parts: a transmitter unit and a transducer. Magnetic external clamps on the sensor are easy to install and connect to metal tubing for continuous flow measurement. It is especially suitable for on-site flow measurement of various pressure requirements. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring clean liquids Power supply: 24VDC/85VAC-2265AC Communication: RS485

Our open channel flow meter display the level, flow rate, accumulate flow at the same time; This ultrasonic water flow meter has Analogue Output: 4-20mA, corresponding to instantaneous flow.
Display: Backlight LCD
The maximum of Accumulative Flow: 9999999.9 m3/h
Accuracy of Change in Level: 1mm or 0.2% of full span (whichever is greater)
Resolution: 1mm
Analogue Output: 4-20mA, corresponding to instantaneous flow
Relays Output: Standard 2 relay outputs(Optional up to 6 relays)
Serial Communication: RS485, MODBUS -RTU standard protocol
Ambient Temperature: -40 ~70 Degree C
Power Supply: DC24V (+5%) 0.2A; AC220V (+20%) 0.1A ;Optional DC12V

DN80 pipe ultrasonic flowmeter water liquid ultrasonic clamp on type is an ultrasonic flowmeter used to measure the flow rate of liquids in closed pipes. The transducer is clamp-on type, which will provide the benefits of contamination-free operation and ease of installation. The transit time flowmeter includes two transducers, which act as ultrasonic transmitters and receivers. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring clean liquids Power supply: 24VDC/85VAC-2265AC Communication: RS485

QT621 portable type ultrasonic clamp on flow meters use clamp-on transducers that are mounted externally on the surface of the pipe and which generate pulses that pass through the pipe wall.
Portable ultrasonic flow meters are widely applicated from simple water flow measurements to energy flow monitoring and automated process control.

Size: 1¡å~48¡å(25mm~1200mm)
Flow Range:¡À0.01 m/s~ ¡À12 m/s
Accuracy: ¡À1%
Repeatability: 0.2%
Output: 4-20mA, RS485
Power supply: Internal lithium 3000mAh
Transducer: IP68

QTDS-100F wall mounted ultrasonic water flowmeter sensor heat meter adopts the self-development measurement technology.This measurement technique is a faster and more accurate process time measurement algorithm. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring single clean liquids Power supply: 24VDC/85VAC-2265AC Communication: RS485

Portable Handheld Ultrasonic Flowmeter Liquid transmitter Ultrasonic Flow Meter no pipe cutting required. The user simply clamp on the flow sensor to the pipe surface. Portable Handheld Ultrasonic Flowmeter Liquid transmitter Ultrasonic Flow Meter can then detect the flow through ultrasonic waves, and then automatically calculate the flow rate value, flow accumulator, etc. No pipe cutting means no damage to the pipe. So as long as the pipes are in good condition, the installation on the flowmeter will not provide the possibility of leakage. Sensor: Clamp-on/External Principle: transmit time Size: DN15mm-DN6000mm Measuring medium: Liquid 3.6V Battery-powered

PN16 Flowmeter Water Wall Mounted Clamp On Ultrasonic Flow Meter Digital Water proven transit-time ultrasonic measurement technology .This technology can be used for permanent installations where intrusive flow meters are not economically viable for permanent installations on large pipelines and for all the different process fluids encountered in the network. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring clean liquids Power supply: 24VDC/85VAC-2265AC Communication: RS485

Fixed type ultrasonic clamp on flow meter adopts the self-development measurement technology.This measurement technique is a faster and more accurate process time measurement algorithm. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring single clean liquids Power supply: 24VDC/85VAC-2265AC Communication: RS485