China hot sell EVC high accuracy gas turbine flow meters

Liquid Turbine Flow Meter with a 4-20 mA output available in 12 sizes covering flow ranges between 0.176 to 880 GPM. Turbine Flow Meters are designed to meet the demands of the most rigorous flow measurement applications. The meter features a 304 stainless steel housing and rotor support, CD4MCU stainless steel rotor, and abrasion-resistant tungsten carbide rotor shaft and 316SS bearings. These materials help the meter to maintain accuracy and mechanical integrity when measuring the corrosive and abrasive fluids found in many industries

Turbine meters measure flow using the mechanical energy of the fluid or gas to rotate a turbine rotor within the flow stream inside the meter. The rotations are measured and calculated to provide a proportional measurement relative to flow rate. The Principle is well proven and the application suitability list is very large.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%/¡À0.2%;
OUTPUT: PULSE/4-20mA;
Digital Communication:RS485, MODBUS; HART

Liquid turbine flowmeter as precision instruments for industrial measurement. turbines turbine flowmeters with the advantages of simple structure, light weight, high precision, good reproducibility, sensitive response, and convenient installation, maintenance and use.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%;
OUTPUT: PULSE+4-20mA;
Digital Communication:RS485, MODBUS; HART

The turbine flow meter is suitable for a wide range of viscosity medium including oil, gas, water and wastewater, chemical, gas utility, power, food and beverage, aerospace, pharmaceutical, etc.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%;
OUTPUT: PULSE+4-20mA;
Digital Communication:RS485, MODBUS; HART
LCD display

QTWG series turbine gas meters are designed to measure natural gas, air,propane and other clean gases. Turbine gas meters
provide high-quality natural gas measurement which could increase efficiency in boiler/burner control and custody transfer applications.
Size:DN25-400mm
Material:Aluminum alloy or stainless steel
Dual Power:3.6V battery powered+DC24V
Output:4-20mA,Pulse,RS485
Accuracy:1.5% or 1.0%

Turbine flowmeters are widely used in petrochemicals, organic liquids, inorganic liquids, liquefied gases, natural gas and fluids at low to middle temperature .Now it is widely used which is next to orifice plate flow meter.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%;
OUTPUT: PULSE+4-20mA;
Digital Communication:RS485, MODBUS; HART

Liquid Turbine Flow, is the turbine flow meter that suitable for liquid flow rate measurement. Like water flow, Diesel flow. Turbine flow meter is the most popular equipment to measure flow electronically. They offer a wide flow and application rangeability. Turbine Flow Meters are easy to maintain, durable and versatile.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%;
OUTPUT: PULSE+4-20mA;
Digital Communication:RS485, MODBUS; HART

Turbine flowmeter measures the flowrate from the number of revolutions of a blade placed in the flow. The speed of revolutions of the blade with an axis parallel to the flow direction is proportional to the speed of the flow. Utilizing the capability of highly accurate measurement for wide range of viscosity, the turbine flowmeter is useful for process control, transactions as well as process control of petroleum products, general chemical fluids, liquefied gas, water, etc.

QTLL series rotary gas meters a high-quality positive displacement roots-type gas meter that is available in a variety of sizes and options. Rotary type gas meters allow for measurement of large amounts of gas flow in a compact gas meter. The rotary gas meter can be used indoors or outdoors.
Size:DN25-200mm
Material:Aluminum alloy or stainless steel
Dual Power:3.6V battery powered+DC24V
Output:4-20mA,Pulse,RS485
Installation: Vertical or Horizontal
Accuracy:1.5% or 1.0%

QTLL series rotary gas meters a high-quality positive displacement roots-type gas meter which is available in a variety of sizes and options. Rotary gas meters adopt high-precision digital temperature sensor, digital pressure sensor which make sure the good performance.
Size:DN25-200mm
Material:Aluminum alloy or stainless steel
Dual Power:3.6V battery powered+DC24V
Output:4-20mA,Pulse,RS485
Installation: Vertical or Horizontal
Accuracy:1.5% or 1.0%

QTWG series turbine gas flow meters are designed to measure natural gas, air,propane and other clean gases in industrial and commercial billing applications. Gas turbine meters provide fast response to changing flow rates with consistent accuracy and various kinds of outputs including 4-20mA, pulse and RS485.

Size:DN25-400mm
Material:Aluminum alloy or stainless steel
Dual Power:3.6V battery powered+DC24V
Output:4-20mA,Pulse,RS485
Accuracy:1.5% or 1.0%

Turbine flowmeters are flow measurement instruments which use axial fluid momentum to turn a multibladed rotor, the angular velocity of which is approximately proportional to the volume flowrate. With appropriate calibration and operation, turbine meters offer precise and highly repeatable measurement of throughput and flowrate.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%;
OUTPUT: PULSE/4-20mA;
Digital Communication:RS485, MODBUS; HART

QTWG series LPG gas turbine flow meter could achieve accurate flow monitoring. With the ability of increasinig efficiency in boiler/burner control, fuel-to-air ratio, and custody transfer applications.
Size:DN25-400mm
Material:Aluminum alloy or stainless steel
Dual Power:3.6V battery powered+DC24V
Output:4-20mA,Pulse,RS485
Accuracy:1.5% or 1.0%

QTWG Turbine gas meter is a popular device for gas-fired, gas pipeline network and city gas field etc. Gas roots flow meters are one of the high quality working performance meters for natural gas measurement, which could highly inrease the efficiency in various custody transfer applications.
Size:DN25-400mm
Material:Aluminum alloy or stainless steel
Dual Power:3.6V battery powered+DC24V
Output:4-20mA,Pulse,RS485
Accuracy:1.5% or 1.0%

QTWG series natural gas flow meter is used to measure gas flow, with the features of high accuracy, low-pressure drop. Wide turndown gas turbine flow meter is custody transfer approval flow meter, widely used in clean gas including natural gas, LPG gas etc.
Size:DN25-200mm
Material:Aluminum alloy or stainless steel
Dual Power:3.6V battery powered+DC24V
Output:4-20mA,Pulse,RS485
Installation: Vertical or Horizontal
Accuracy:1.5% or 1.0%

About turbine flowmeter pulse,This pulse frequency output can be displayed either on a direct mount or remotely mounted flow meter display and totaliser to provide flow rate indication and total flow and to allow for remote batch control with electromechanical relay options. Electronic frequency to analogue converters is also available upon request if 4¡­20 mA or voltage outputs are required.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%/¡À0.2%;
OUTPUT: PULSE/4-20mA;
Digital Communication:RS485, MODBUS; HART

turbine flowmeter advantage
1.High accuracy, generally up to ¡À1%R, ¡À0.5%R, high accuracy up to 0.2%R
2.Good repeat-ability, short-term repeat-ability up to 0.05% ~ 0.2%, in the trade settlement is the preferred choice of flow meter.
3.Output of pulse frequency signal, suitable for totalizer and connection with PC; no zero shift and strong interference resist
4.High frequency signal(3~4KHz) can be obtained, the signal resolution is strong.
5.Wide range, medium and large diameter up to 1:20, small caliber 1:10.

QTWG series turbine gas meters with electronic totalizer and integrated temperature and pressure compensation. Turbine gas meters with built-in battery operation, with external power supply optional. With display of pressure, temperature, flowrate, totalizer etc.

Size:DN25-400mm
Material:Aluminum alloy or stainless steel
Dual Power:3.6V battery powered+DC24V
Output:4-20mA,Pulse,RS485
Accuracy:1.5% or 1.0%

turbine flow meter advantage
For a wide range of applications in even the most challenging conditions
Individual calibration of each flow meter
Full stainless-steel design
Large temperature and pressure ranges

A turbine flow meter is a volumetric metering the meter consists of a rotor and bearing assembly Suspended on a shaft, which is mounted to a support device.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%;
OUTPUT: PULSE/4-20mA;
Digital Communication:RS485, MODBUS; HART

QTLL series gas roots flow meter is is based on the working principle of volumetric measurement. Rotary gas meter is used to accurately measure the gas flow through a closed pipeline, widely used for custody transfer gas measurements of all non-corrosive gases such as natural gas, propane, butane, air, hydrogen, etc.
Size:DN25-200mm
Material:Aluminum alloy or stainless steel
Dual Power:3.6V battery powered+DC24V
Output:4-20mA,Pulse,RS485
Installation: Vertical or Horizontal
Accuracy:1.5% or 1.0%

Turbine flow meters are used to measure clean, dry gases and liquids such as hydrocarbons, chemicals, gases and vapors, fuels and other types of liquids with lower viscosity, and for applications requiring highly accurate and precise measurements.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%/¡À0.2%;
OUTPUT: PULSE/4-20mA;
Digital Communication:RS485, MODBUS; HART

QTLL series rotary gas meters adopt high-strength aluminum alloy material which could ensure corrosion resistance and long service life,
Rotary gas meters are designed to meet the highest demands of reliable and accurate measurement of gas flow. Ideal for custody transfer grade metering or sub-metering for all different types of gases including Natural Gas and Propane Vapor.
Size:DN25-200mm
Material:Aluminum alloy or stainless steel
Dual Power:3.6V battery powered+DC24V
Output:4-20mA,Pulse,RS485
Installation: Vertical or Horizontal
Accuracy:1.5% or 1.0%

Turbine flow meter is the most popular equipment to measure flow electronically. Offer a wide flow and application rangeability. Turbine Flow Meters are easy to maintain, durable and versatile.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%;
OUTPUT: PULSE+4-20mA;
Digital Communication:RS485, MODBUS; HART

liquid turbine flow meter is a new type of intelligent instrument with integrated turbine flow sensor and display product calculation developed by advanced ultra-low power single-chip microcomputer technology, which has obvious advantages such as compact mechanism, clear reading, high reliability, undisturbed by external power supply, lightning resistance and low cost.

Turbine flow meters are mechanical meters that have a freely rotating turbine set in the path of a fluid stream. The flowing liquid or gas causes the turbine to spin upon its axis. The rate of spin will be proportional to the velocity of the flow. Turbine flow meters are simple and reliable.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%;
OUTPUT: PULSE+4-20mA;
Digital Communication:RS485, MODBUS; HART

The high-precision turbine flowmeter is a high-grade liquid flow meter. It is based on Swiss flow patent technology. The rotor radial flow caused by the special geometric combination of the rotor shell is combined with the lightweight polyethylene fiber rotor to make the rotor in Floating in the middle.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%/¡À0.2%;
OUTPUT: PULSE/4-20mA;
Digital Communication:RS485, MODBUS; HART

QTWG series intelligent explosion proof turbine gas meters are designed to measure natural gas, air,propane and other clean gases. Natural gas turbine meters provide very accurate flow monitoring.?Has an good ability to provide fast response to changing flow rates with consistent accuracy.
Size:DN25-400mm
Material:Aluminum alloy or stainless steel
Dual Power:3.6V battery powered+DC24V
Output:4-20mA,Pulse,RS485
Accuracy:1.5% or 1.0%

QTWG series explosion proof turbine gas meters are widely used for gas-fired, gas pipeline network, and city gas field etc.Turbine gas meters offer high capacity ability for various custody transfer applications, with the features of low pressure loss, high accuracy and good anti-vibration.
Size:DN25-400mm
Material:Aluminum alloy or stainless steel
Dual Power:3.6V battery powered+DC24V
Output:4-20mA,Pulse,RS485
Accuracy:1.5% or 1.0%

turbine flowmeter hydrodynamic positioning of the low mass rotor provides wider rangeability and longer bearing life than that of conventional turbine flowmeters. Integral flow straightening tubes minimize the effects of upstream flow turbulence. The housing is made of non-magnetic materials. The rotor is made of magnetic or magnetized material. Bearings are chosen based on service fluid, cost, and accuracy considerations.