CE approval impeller flow meter turbine gas flow meters

The precision turbine flow meter offers outstanding accuracy and reliability.
With rugged stainless steel body,the turbine flow meter is compatible with most chemicals and will stand up well to high pressure applications.With high pressure ANSI 150# RF flange connections.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%;
OUTPUT: PULSE+4-20mA;
Digital Communication:RS485, MODBUS; HART
LCD display

About turbine flowmeter pulse,This pulse frequency output can be displayed either on a direct mount or remotely mounted flow meter display and totaliser to provide flow rate indication and total flow and to allow for remote batch control with electromechanical relay options. Electronic frequency to analogue converters is also available upon request if 4¡­20 mA or voltage outputs are required.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%/¡À0.2%;
OUTPUT: PULSE/4-20mA;
Digital Communication:RS485, MODBUS; HART

turbine flow meter is available in a wide range of body sizes and styles to suit liquid flow applications for low to medium viscosity fluids.
The principle of operation is based on a permanent magnet contained within a pick-off coil on the body and a ferritic stainless steel rotor which revolves when flow is present. A small AC voltage is generated in the coil as the rotor tip passes the magnet. The frequency of this AC voltage is directly proportional to the flow rate. The total number of pulses produced represents the total flow passed through the meter.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%/¡À0.2%;
OUTPUT: PULSE/4-20mA;
Digital Communication:RS485, MODBUS; HART

Gas turbine flow meter is widely used in gas measuring from Petroleum, Chemical, Electricpower,Industrial boiler etc. Natural gas flow meter is a kind of accurate measurement instruments for natural gas, LPG gas application.
Size:DN25-400mm
Material:Aluminum alloy or stainless steel
Dual Power:3.6V battery powered+DC24V
Output:4-20mA,Pulse,RS485
Accuracy:1.5%/1.0%

QTWG turbine gas flow meters are ideal flow measurement device for clean gas, including natural gas, LPG gas etc. Turbine gas meters are very stable measurement device which could achieve high-precision custody transfer metering, could be automatically pressure- and/or temperature-compensated.
Size:DN25-400mm
Material:Aluminum alloy or stainless steel
Dual Power:3.6V battery powered+DC24V
Output:4-20mA,Pulse,RS485
Accuracy:1.5% or 1.0%

QTWG turbine gas flow meters are designed to accurately measure natural gas, air, nitrogen, carbon dioxide, propane vapor, and other non-corrosive gases for large volume commercial and industrial uses. they are ideal flow measurement device for clean gas, including natural gas, LPG gas etc. With user-friendly display, support of flowrate, temperature, pressure each in operating and standard status. Turbine gas meters support a wide range of measurement including maximum working pressure and maximum measuring flow rate.

Size:DN25-400mm
Material:Aluminum alloy or stainless steel
Dual Power:3.6V battery powered+DC24V
Output:4-20mA,Pulse,RS485
Accuracy:1.5% or 1.0%

Turbine meters measure flow using the mechanical energy of the fluid or gas to rotate a turbine rotor within the flow stream inside the meter. The rotations are measured and calculated to provide a proportional measurement relative to flow rate. The Principle is well proven and the application suitability list is very large.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%/¡À0.2%;
OUTPUT: PULSE/4-20mA;
Digital Communication:RS485, MODBUS; HART

liquid turbine flowmeter, as fluid flows through turbine rotor and drives it to rotate, the rotating rotor periodically cuts magnetic field line to generate electric pulse signal, which can be transmitted to output and transferred to the meter to display flow rater or totalizer. It features in high accuracy, good repeatability, simple structure, low pressure loss, convenient maintenance, etc. It is ideal to measure the volume of low-viscosity liquids in closed pipes, such as tap and demineralized water, fuels, liquefied gases, light fuel oil, solvents, pharmaceutical fluids, food etc.

Gas turbine flow meter is one kind of precisionmeasuring instruments which for gas measuring. Gas turbine flowmeter has the characteristics of low pressure loss,high accuracy,low initiating flow,anti vibration and pulsation flow resistance,widelyrange ratio etc.
Size:DN25-400mm
Material:Aluminum alloy or stainless steel
Dual Power:3.6V battery powered+DC24V
Output:4-20mA,Pulse,RS485
Accuracy:1.5%/1.0%

Turbine flowmeter installation
Normally turbine flow meter has flange, thread, clamp-on connections, and the fluids direction should be the same as the arrow on the meter body. The liquid turbine flow sensor can be installed horizontally and vertically, and the fluid direction must be upward when installed vertically.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%/¡À0.2%;
OUTPUT: PULSE/4-20mA;
Digital Communication:RS485, MODBUS; HART

QTLL series rotary gas meters adopt high-strength aluminum alloy waist wheel, corrosion resistance and long service life,
Gas rotary meter with the features of high accuracy, and good repeatability; Based on the principle of
volumetric measurement, rotary gas flow meter is used to accurately measure the gas flow through a closed pipeline.
Size:DN25-200mm
Material:Aluminum alloy or stainless steel
Dual Power:3.6V battery powered+DC24V
Output:4-20mA,Pulse,RS485
Installation: Vertical or Horizontal
Accuracy:1.5% or 1.0%

turbine flow meters are used for the precise measurement of instantaneous flow rates of low-viscosity fluids such as tap and demineralized water, fuels, liquefied gases, light fuel oils, solvents, and pharmaceutical fluids
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%;
OUTPUT: PULSE+4-20mA;
Digital Communication:RS485, MODBUS; HART

Turbine Flowmeter has simple structure, high accuracy, good repetitiveness, fast response and
convenient maintenance. It is widely used for liquid without corrosion to stainless steel, Al2O3 or hard alloy, without fibre or particle and kinematic viscosity less than 50¡Á10-6m2/s.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%;
OUTPUT: PULSE+4-20mA;
Digital Communication:RS485, MODBUS; HART
LCD display

Turbine flowmeter is a precision flow measuring instrument, which can be used to measure the flow and total amount of liquid when matched with the corresponding flow totalizer. It is widely used in metering and control systems in petroleum, chemical, metallurgy, scientific research and other fields. Turbine flow sensors with sanitary fittings can be used in the pharmaceutical industry. The structure of the integrated turbine flowmeter is explosion-proof and can display the total flow, instantaneous flow and percentage of full flow.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%/¡À0.2%;
OUTPUT: PULSE/4-20mA;
Digital Communication:RS485, MODBUS; HART

QTWG turbine gas flow meters are ideal flow measurement device for clean gas, including natural gas, LPG gas etc. With user-friendly display, support of flowrate, temperature, pressure each in operating and standard status. Turbine gas meters support a wide range of measurement including maximum working pressure and maximum measuring flow rate.

Size:DN25-400mm
Material:Aluminum alloy or stainless steel
Dual Power:3.6V battery powered+DC24V
Output:4-20mA,Pulse,RS485
Accuracy:1.5% or 1.0%

turbine flow meters are used for the precise measurement of instantaneous flow rates of low-viscosity fluids such as tap and demineralized water, fuels, liquefied gases, light fuel oils, solvents, and pharmaceutical fluids. Turbine flowmeters measure volumetric flow, where fluid passing through the meter body is measured by the mean velocity of the flowing fluid media. Flow rectifiers ensure a laminar flow in the axial direction of the wheel. A low-mass turbine wheel carried concentrically within the meter body is rotated by the fluid. The RPM of the turbine wheel is directly proportional to the mean flow rate within the meter body and directly corresponds to the volumetric flow over a wide range.

turbine flowmeter can be applied to alcohol, toluene, etc. which are not electrically conductive. And it can be used also in oil and gas, power plants, pharmaceutical and pulp & paper-making industry. However, it is recommended to not use for fluids containing sludge or highly viscous fluids. Also, it can be provided in flange type or screw (male or female) type while being able to cope with various piping conditions.

A turbine flow meter is a volume sensing device. As liquid or gas passes through the turbine housing, it causes the freely suspended turbine blades to rotate. The velocity of the turbine rotor is directly proportional to the velocity of the
Turbine flowmeters are widely used in the following measurement objects: petroleum, organic liquids, inorganic liquids, liquefied gas, natural gas, coal gas and cryogenic fluids. It is widely used in foreign transshipment and gathering stations of liquefied petroleum gas, refined oil and light crude oil, as well as the first and last stations of large crude oil pipelines for trade settlement.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%/¡À0.2%;
OUTPUT: PULSE/4-20mA;
Digital Communication:RS485, MODBUS; HART

Turbine gas meters are popular devices for gas-fired, gas pipeline network and city gas field etc, with various kinds of output signals available. As a type of smart meter, gas impeller flow meter is very reasonably priced with good reliability and quality.

Size:DN25-400mm
Material:Aluminum alloy or stainless steel
Dual Power:3.6V battery powered+DC24V
Output:4-20mA,Pulse,RS485
Accuracy:1.5% or 1.0%

turbine flowmeter is widely used in low flow rate and low viscosity Liquid measurement. Converting sensor signals into smart signal outputs through a microcomputer
processor design.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%;
OUTPUT: PULSE+4-20mA;
Digital Communication:RS485, MODBUS; HART

Turbine flowmeter is a precision flow measuring instrument, which can be used to measure the flow and total amount of liquid when matched with the corresponding flow totalizer. Used in conjunction with our company’s quantitative controller, it can perform high-precision quantitative control of liquid feeding. Widely used in metering and control systems in petroleum, chemical, metallurgy, scientific research and other fields
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%/¡À0.2%;
OUTPUT: PULSE/4-20mA;
Digital Communication:RS485, MODBUS; HART

QTWG series turbine gas meters are designed to measure natural gas, air,propane and other clean gases. Turbine gas meters
provide high-quality natural gas measurement which could increase efficiency in boiler/burner control and custody transfer applications.
Size:DN25-400mm
Material:Aluminum alloy or stainless steel
Dual Power:3.6V battery powered+DC24V
Output:4-20mA,Pulse,RS485
Accuracy:1.5% or 1.0%

Turbine flowmeter installation
Normally turbine flow meter has flange, thread, clamp-on connections, and the fluids direction should be the same as the arrow on the meter body. The liquid turbine flow sensor can be installed horizontally and vertically, and the fluid direction must be upward when installed vertically. The liquid should be filled with tubing and must be free of air bubbles. The inner wall of the straight pipe section should be smooth and clean, free of defects such as dents, scale and peeling.

turbine flow meter can be used for liquid flow measurement such as water and oil in the pipe size of DN4 ~ DN200 mm, 1.0%R measuring accuracy, 24V DC power supply, threaded or flange connection.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%;
OUTPUT: PULSE+4-20mA;
Digital Communication:RS485, MODBUS; HART

liquid turbine flowmeter, It features in high accuracy, good repeatability, simple structure, low pressure loss, convenient maintenance, etc. It is ideal to measure the volume of low-viscosity liquids in closed pipes, such as tap and demineralized water, fuels, liquefied gases, light fuel oil, solvents, pharmaceutical fluids, food etc.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%/¡À0.2%;
OUTPUT: PULSE/4-20mA;
Digital Communication:RS485, MODBUS; HART

QTLL series rotary gas meters are suitable for custody transfer gas measurement of all non-corrosive gases such as natural gas, propane, butane, air, hydrogen etc. Rotary gas meters adopt high-strength aluminum alloy material which could ensure corrosion resistance and long service life.
Size:DN25-200mm
Material:Aluminum alloy or stainless steel
Dual Power:3.6V battery powered+DC24V
Output:4-20mA,Pulse,RS485
Installation: Vertical or Horizontal
Accuracy:1.5% or 1.0%

Liquid Turbine Flow, is the turbine flow meter that suitable for liquid flow rate measurement. Like water flow, Diesel flow. Turbine flow meter is the most popular equipment to measure flow electronically. They offer a wide flow and application rangeability. Turbine Flow Meters are easy to maintain, durable and versatile.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%;
OUTPUT: PULSE+4-20mA;
Digital Communication:RS485, MODBUS; HART

QTWG turbine gas meter is a type of high-precision custody transfer metering. As a ideal flow measurement device for natural gas or other non-corrosive gases applications, gas turbine flow meter urbine could be automatically pressure and temperature compensation to obtain volumetric measurements in standard units.

Size:DN25-400mm
Material:Aluminum alloy or stainless steel
Dual Power:3.6V battery powered+DC24V
Output:4-20mA,Pulse,RS485
Accuracy:1.5% or 1.0%

Sanitary turbine flow meters have stainless steel bodies and come standard with Tri-Clover fittings. Sanitary flow meter is suitable for measuring liquid without impurities. It can output pulse frequency signal. It is used to detect instantaneous flow and total integrated flow. Sanitary flow meter can be used in food, sport drink, liquor and other beverage industries, in preprocess applications.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%/¡À0.2%;
OUTPUT: PULSE/4-20mA;
Digital Communication:RS485, MODBUS; HART

QTWG natural gas turbine flow meters are are ideal flow measurement device for natural gas or other non-corrosive gases applications. Turbine gas meters with wide range ratio which could achieve different flow range measurements.
Size:DN25-400mm
Material:Aluminum alloy or stainless steel
Dual Power:3.6V battery powered+DC24V
Output:4-20mA,Pulse,RS485
Accuracy:1.5% or 1.0%