Battery Power Magnetic Water Fluid Water Meter

No Moving Parts
RS485 Standard,HART standard is available.
Suitable for Pipes Up to DN300
Pulse, Gprs output
Standard 5 points calibration Included

DC3.6V powered electromagnetic flowmeter special for the area without AC220V/DC24V power supply, battery mag meter transfer and monitor data via 4-20mA, pulse, RS485, GPRS. Nominal Pressure: 0.6-1.6MPa (2.5Mpa / 4.0Mpa /6.4Mpa…Max 42Mpa); Accuracy: ¡À0.5% (Standard), ¡À0.3% or ¡À0.2% (Optional); Liner: PTFE,Neoprene,Hard Rubber,EPDM,FEP, Polyurethane,PFA; Electrode: SUS316L,Hastelloy B,Hastelloy C, Titanium,Tantalum,Platinum-iridium; Structure: Integral,remote,submersible,ex-proof; Medium Temperature: -20¡æ~+60¡æ (integral type), Remote type(neoprene,Hard rubber,Polyurethane, EPDM) -10¡æ~+80¡æ; Remote type (PTFE / PFA / FEP)-10¡æ~+160¡æ; Ambient Temperature: -20¡æ~+60¡æ;

water flow meter, also known as electromagnetic flowmeter or mag meter, is widely used because less obstruction, cost-effective and accurate measurement. liquid flow meter don’t have any moving parts to wear down, reducing the need for maintenance or replacement. water flow meter is calibrated by Mass Method liquid calibration equipment, which is approved by CNAS ISO 17025, which is mutual recognition by ilac-MRA.

Structure: compact, remote
Liner: PTFE, PFA, Polyurethane, Neoprene, Hard Rubber, Ceramic
Output Signal: 4~20 mA, Pulse
Communication: RS485, HART, PROFIBUS
Protection Grade: IP65 std, IP68 optional for remote

Accuracy of mag flow meter is ¡À0.5% standard, ¡À0.2% is optional, magmeter is calibrated on ¡À0.2% accuracy calibration device. A flow transmitter energizes the coils which creates a magnetic field in the tube. A conductive fluid moving through this field generates an induced voltage at two electrodes in the tube. waste water flow meter can be compact type and remote type, standard cable length is 10m and max cable length is 120m.

Size: 1/8″-120″
Accuracy: ¡À0.5%
Structure: compact, remote
Output Signal: 4~20 mA, Pulse
Communication: RS485, HART, PROFIBUS
Velocity: 0.1~15 m/s

3.6V battery meter satisfy urban water supply to ensure accurate water fee calculation,DC3.6V powered magnetic flow meter is widely used in no power supply region. Structure: Integral,remote,submersible,ex-proof; Ambient Humidity: 5-100%RH (relative humidity); Protection Class: IP65(Standard), IP68(Optional for remote type); Process Connection: Flange(Standard),Wafer,Thread,Tri-clamp etc(optional); Output Signal: 4-20mA / pulse (optional); Communication: RS485(Optional),HART(Optional),GPRS/GSM(Optional); Power Supply: Battery powered 3.6V,Battery powered 3.6V +DC24V(Optional); Power Consumption: 0.5W(Standard),1.5W(with DC24V);

Size DN50 to DN300 pipe line
Suitable for all conductive liquids
No moving parts
Near zero pressure drop
Wide range in electrode: SS316, Ti, HC, HB, Ta, Pt
Multi-choice in flange: DIN, GB, ANSI, JIS, EN, etc

3.6V battery powered magnetic flow meter service life with 5 years, 3.6V battery powered mag flow meter fulfills the special customer demands to water application as well as irrigation. Nominal Pressure: 0.6-1.6MPa(2.5Mpa / 4.0Mpa /6.4Mpa…Max 42Mpa); Accuracy: ¡À0.5% (Standard), ¡À0.3% or ¡À0.2% (Optional); Measuring Range: Max 15m/s; Conductivity: >5us/cm; Protection Class: IP65(Standard),IP68(Optional for remote type); Output Signal: 4-20mA / pulse (optional); Communication: RS485(Optional),HART(Optional),GPRS/GSM(Optional); Power Supply: Battery powered 3.6V,Battery powered 3.6V +DC24V(Optional);

Easy Setup
Minimal Straight Pipe
Forward or Reverse flow and Total
IP65,IP67 ,IP68 Rated (optional)
Virtually No Pressure Loss

a non full tube electromagnetic flow meter which can automatically display the instantaneous flow velocityand cumulative flow is composed of converter, flow sensor and level sensor. The user only needs to
enter the diameter of pipe, the non-full pipe flowmeter will automatically calculate the flow rate, and automatically
display the instantaneous flow, total flow, velocity, height, etc. It can measure liquid volume min 10% of full pipe. It is
especially suitable for the needs of municipal rainwater, waste water, sewage discharge and irrigation

magentic flow meters are designed for the conductive liquids. Flow in all kinds of conductive liquids can be accurately measured by utilizing the pulsating magnetic fields. These meters are designed with advanced filtering and signal processing circuitry to maximize performance and reliability.
Velocity: 0.1~15 m/s
Conductivity: > 5 ¦ÌS/cm, demineralized water > 20 ¦ÌS/cm
Power supply: 85~250 VAC, 20V~36VDC, 3.6V lithium battery
Sensor material: carbon steel (std), SS304 / SS316 (optional)
Flange: ANSI, DIN, JIS, etc.

communication of magnetic flow meter is RS485, HART, Profibus DP and PA. Measurement of magnetic flowmeter is independent of fluid density, viscosity, temperature, pressure, and conductivity. the pipe is PVC, so we configure grounding rings to have better grounding to protect the electromagnetic flow meter.

Structure: compact, remote
Output Signal: 4~20 mA, Pulse
Communication: RS485, HART, PROFIBUS
Velocity: 0.1~15 m/s
Power supply: 85~250 VAC, 20V~36VDC, 3.6V lithium battery

Battery power mag flowmeter enjoys ¡À0.5% accuracy, installation should be away from pumps,tees,elbows,valves,etc., 3.6V magmeter requires front straight pipeline 5D, rear 3D. Size: DN10-DN2000; Accuracy: ¡À0.5% (Standard), ¡À0.3% or ¡À0.2% (Optional); Structure: Integral,remote,submersible,ex-proof; Ambient Humidity: 5-100%RH (relative humidity); Protection Class: IP65(Standard),IP68(Optional for remote type); Process Connection: Flange(Standard),Wafer,Thread,Tri-clamp etc(optional); Output Signal: 4-20mA / pulse (optional); Communication: RS485(Optional),HART(Optional),GPRS/GSM(Optional);

Electromagnetic water meter is powered with Li-ion battery pack; Doesn’t need external power source;
Type E-mag W electromagnetic flow meter has two communication ways:RS485,GPRS.

Q&T has sufficient flow meter stock,could guarantee fast delivery of 3.6V battery powered electromagnetic flow meter,battery meter is ideal for working site without power. Accuracy: ¡À0.5% (Standard),¡À0.3% or ¡À0.2% (Optional); Liner: PTFE,Neoprene,Hard Rubber,EPDM,FEP,Polyurethane,PFA; Electrode: SUS316L,Hastelloy B,Hastelloy C,Titanium,Tantalum,Platinum-iridium; Structure: Integral,remote,submersible,ex-proof; Ambient Temperature: -20¡æ~+ 60¡æ; Ambient Humidity: 5-100% RH (relative humidity); Process Connection: Flange(Standard),Wafer,Thread,Tri-clamp etc(optional); Output Signal: 4-20mA/pulse (optional);

inline magnetic flow meter has self-checking function, it will display when there is any problem. Liner with PTFE, Neoprene, PFA, FEP is optional, standard material of sensor material is carbon steel, SS304 or SS316 is optional, waste water flow meter can be customized color and logo, Q&T Instrument is OEM for many European and Amercian brands. warranty is 2 years. electromagnetic flowmeter is volumetric flow meter that measure the flow when conductive liquids move through a magnetic field.

Output Signal: 4~20 mA, Pulse
Communication: RS485, HART, PROFIBUS
Protection Grade: IP65 std, IP68 optional for remote
Velocity: 0.1~15 m/s
Conductivity: > 5 ¦ÌS/cm, demineralized water > 20 ¦ÌS/cm

Battery power electromagnetic flow meter satisfy water fee calculation with high accuracy,3.6V magmeter is widely used in applications without power grid, can work with solar power supply. Accuracy: ¡À0.5% (Standard), ¡À0.3% or ¡À0.2% (Optional); Ambient Humidity: 5-100%RH (relative humidity); Protection Class: IP65(Standard), IP68(Optional for remote type); Process Connection: Flange(Standard),Wafer,Thread,Tri-clamp etc(optional); Output Signal: 4-20mA / pulse (optional); Communication: RS485(Optional),HART(Optional),GPRS/GSM(Optional); Power Supply: Battery powered 3.6V,Battery powered 3.6V +DC24V(Optional); Power Consumption: 0.5W(Standard),1.5W(with DC24V);

electromagnetic flow meter’s accuracy is ¡À0.5% standard, ¡À0.2% is optional, liquid flow meter is calibrated on ¡À0.2% accuracy test bench, mag flowmeter is calibrationed 5 points by comparison method or mass method. our calibration lab has been approved CNAS ISO/IEC 17025:2017.
Structure: compact, remote
Liner: PTFE, PFA, Polyurethane, Neoprene, Hard Rubber, Ceramic
Protection Grade: IP65 std, IP68 optional for remote
Size: DN3-DN3000
Sensor material: carbon steel (std), SS304 / SS316 (optional)
Measuring tube: SS304

Q&T have 8 sets calibration device for liquids mag flowmeter and 5 sets calibration equipments for gas. our calibration lab has been approved CNAS ISO/IEC 17025:2017. magnetic flow meter can add pt1000 temeprature sensor to be magnetic btu meter to monitor flow and btu of hot water and cold water, can calibrated on liquid test bench, standard accuracy is ¡À0.5%

Repeatability: 0.17%
Electrode: SUS316L, Hastelloy B, Hastelloy C
Structure: compact, remote
Liner: PTFE, PFA, Polyurethane, Neoprene, Hard Rubber, Ceramic
Output Signal: 4~20 mA, Pulse

protection grade of mag flowmeter sensor is IP68 for split type and IP65 for integrated mag flowmeter. QTLD series electromagnetic flow meter represent the state-of-the-art for accurate measurement in water cycle and process applications. This new-generation meter incorporates improvements to the magnetic distribution elements that allow accurate operation throughout all flow regimes.

Size: DN3-DN3000
Accuracy: ¡À0.5%
Electrode: SUS316L, Hastelloy B, Hastelloy C
Structure: compact, remote
Output Signal: 4~20 mA, Pulse
Communication: RS485, HART, PROFIBUS

Self-diagnosis fault alarm
GSM data infinitely transmitted
LCD display cumulative flow£¬instanta-
neous flow£¬ flow rate,flow percentage,etc.

The Magnetic flow meter converter has self-inspection and self-diagnosis function; The sensor of high pressure electromagnetic flow meter use PFA and net lining material, have the advantages of high pressure resistance, anti-negative pressure. This water flow meter is specially used in petrochemical, mineral, etc. Explosion-proof type flow meter can be used in explosive area.

Specifications:
Accuracy: ±0.5%
Electrode: SUS316L, Hastelloy B, Hastelloy C
Structure: compact, remote
Liner: PTFE, PFA, Polyurethane, Neoprene, Hard Rubber, Ceramic
Output Signal: 4~20 mA, Pulse
Communication: RS485, HART, PROFIBUS
Protection Grade: IP65 std, IP68 optional for remote
Velocity: 0.1~15 m/s
Conductivity: > 5 μS/cm, demineralized water > 20 µS/cm
Power supply: 85~250 VAC, 20V~36VDC, 3.6V lithium battery

high accuracy and won’t be influenced by downstream or DC water or blocking partial filled pipe flow meter an accurate mini ultrasonic level meter for its liquid level measurement then the flow meter will record
the liquid level and use this parameter to measure liquid flow. This ultrasonic level meter’s blind area is very
small and its accuracy can reach ¡À1mm.

Electromagnetic flow meter detect flow by Faraday’s Law of induction. Size can be 1/8″~120″, magnetic flowmeter can be calibrated according to CNAS ISO/IEC 17025:2017, which is recongition by ILAC-MAR.
Size: 1/8″-120″
Accuracy: ¡À0.5%
Electrode: SUS316L, Hastelloy B, Hastelloy C
Structure: compact, remote
Liner: PTFE, PFA, Polyurethane, Neoprene, Hard Rubber, Ceramic

Newest Product Partial Filled Pipe Flow Meter Sewage Stainless Steel Variable Area Water Flowmeters RS485 flow meters is composed of converter, flow sensor and level sensor. The user only needs to
enter the diameter of pipe, the non-full pipe flowmeter will automatically calculate the flow rate, and automatically
display the instantaneous flow, total flow, velocity, height, etc. It can measure liquid volume min 10% of full pipe. It is
especially suitable for the needs of municipal rainwater, waste water, sewage discharge and irrigation

The converter of electromagnetic water meter adopts novel exci-tation mode with low power consumption, stable zero pointand high precision. The flow range can reach 150:1, and themeasurement is not affected by the changes of fluid density,
viscosity,temperature, pressure and conductivity
Full digital signal processing, stable measurement, high measurement accuracy Automatic two-way flow measurement, on-site instantaneous flow, positive and negative cumulative total display

Electromagnetic water meter is manufactured with the present up-to-data technology for electromagnetic flowmeter. It has the following characteristics:
The measurement is independent of density, viscosity, temperature, pressure and the change of conductivity of the fluid;

sensor of magmeter is carbon steel, SS304 and SS316 is optional, liner material is PTFE, which approved NSF and FDA. It is NSF approved allowing the 1400C to be used on potable (drinking) water applications. This Inline battery-powered magmeter is specially designed for applications where electricity and power supply availability is unavailable. It provides up to 5 years of battery life, minimizing maintenance and enhancing smart measurements¡¯ productivity in field instruments.

Size: 1/8″-120″
Structure: compact, remote
Liner: PTFE, PFA, Polyurethane, Neoprene, Hard Rubber, Ceramic
Power supply: 85~250 VAC, 20V~36VDC, 3.6V lithium battery
Size: DN3-DN3000
Measuring tube: SS304

DC3.6V powered electromagnetic flowmeter could reach IP68 protection,3.6V battery powered mag flow meter could put under water for long time, flow meter also have external DC12-24V power. Size: DN10-DN2000; Nominal Pressure: 0.6-1.6MPa(2.5Mpa / 4.0Mpa /6.4Mpa…Max 42Mpa); Accuracy: ¡À0.5% (Standard), ¡À0.3% or ¡À0.2% (Optional); Structure: Integral,remote,submersible,ex-proof; Medium Temperature: -20¡æ~+60¡æ (integral type), Remote type(neoprene,Hard rubber,Polyurethane, EPDM) -10¡æ~+80¡æ; Remote type (PTFE / PFA / FEP)-10¡æ~+160¡æ; Protection Class: IP65(Standard),IP68(Optional for remote type); Output Signal: 4-20mA / pulse (optional); Communication: RS485(Optional),HART(Optional),GPRS/GSM (Optional);

Our magnetic flow meters are CE certificated, it is widely used for conductive liquids, our magnetic-inductive flow meters can be used for liquids and liquid/solid mixes (20 and 3 µS/cm) such as: water, pulps, pastes, slurries, acids, solvents, lyes, sap, emulsions, ore slurries, sand or water mixes.

Specifications:
Accuracy: ±0.5%
Electrode: SUS316L, Hastelloy B, Hastelloy C
Structure: compact, remote
Liner: PTFE, PFA, Polyurethane, Neoprene, Hard Rubber, Ceramic
Output Signal: 4~20 mA, Pulse
Communication: RS485, HART, PROFIBUS
Protection Grade: IP65 std, IP68 optional for remote
Velocity: 0.1~15 m/s
Conductivity: > 5 μS/cm, demineralized water > 20 µS/cm
Power supply: 85~250 VAC, 20V~36VDC, 3.6V lithium battery

Q&T series electromagnetic flow meters sensor and transmitter integrity check utilizing fingerprint technology . Verify the installation is correct from day one and Receive timed notifications. Protect your investment in Q&T flowmetering. Q&T Series nominal diameter DN3-DN3000. There are many options for sensor liner and electrode materials.

Size: 1/8″-120″
Accuracy: ¡À0.5%
Electrode: SUS316L, Hastelloy B, Hastelloy C
Structure: compact, remote
Liner: PTFE, PFA, Polyurethane, Neoprene, Hard Rubber, Ceramic
Output Signal: 4~20 mA, Pulse
Communication: RS485, HART, PROFIBUS
Protection Grade: IP65 std, IP68 optional for remote
Velocity: 0.1~15 m/s
Conductivity: > 5 ¦ÌS/cm, demineralized water > 20 ¦ÌS/cm
Power supply: 85~250 VAC, 20V~36VDC, 3.6V lithium battery
Size: DN3-DN3000
Sensor material: carbon steel (std), SS304 / SS316 (optional)
Flange: ANSI, DIN, JIS, etc.
Measuring tube: SS304
Function: High and low alarm, exciting alarm, empty pipe alarm, self-diagnosis