5inch thermal gas mass flow meter with LCD display

Q&T thermal gas mass flow meter with DC4-20mA four-wire output,which is more convenient for remote reception.Support MODBUS RTU RS485 protocol,coordinating the receiving system to collect more data ans modify system
Insertion rod diameter :
DN32~DN50 standard rod dia. 12mm ,14mm is optional
DN65~DN4000 standard rod dia.19mm,12mm and 14mm is optional

Critical nozzle flow calibration device could load the factor which is stored by systom to the quantity production,same model,same diameter and under calibrated thermal flowmeters,Just need to test the thermal gas mass flow meter and the process of calibration will be finished by factor amend function of this calibration device.
Q&T¡®s every thermal gas mass flowmeters be calibrated by critical nozzl flow calibration device to ensure flow meters accuracy

Thermal meters require a fully developed flow profile as a prerequisite for correct flow measurement.
When the gas is very humid or saturated with water (e. g. Bio Gas), the piping and flowmeter body should be insulated to prevent water droplets condensing on the measuring sensor.
DC4-20mA four-wire output
Mass flow unit
Dual power:24VDC,220VAC
Min.Flow veloctiy:0.1Nm/s
Output:4-20mA

Gas mass flow meter also means thermal gas mass flow meter.
Thermal mass flow meters measure the mass flowrate of fluids by measuring the heat conducted from a heated surface to the flowing fluid. Since a flowing fluid removes a known quantity of heat as it passes, the temperature difference between the heated sensor and the flow stream is directly proportional to the mass flow rate.
Output:4-20mA
Accuracy:¡À1.0%~¡À1.5%
Probe material:SS316L
Power supply:24VDC ,220VAC
Response time:1S
Display:4 line digital

Thermal flow meter measure gas mass flow in various processes and offer distinct advantages, such as repeatability, low maintenance, and operating over a wide flow range. Here we discuss the meter¡¯s fundamentals, the working principle of thermal mass flow measurement, and the two approaches to measuring heat dissipation.
Accuracy:
In-line type accuracy:¡À1.0%
Insertion type accuracy::¡À1.5%
Power supply:DC24V and AC220V
Output:4-20mA,Pulse,RS485

Insertion type thermal gas mass flow meter need to reserve 20mm mounting hole,which could be used to weld and fix the base,Inline type thermal gas mass flow meter could be min.size 10mm.
Easy installation and maintenance. If the conditions on site are permissible, the meter can achieve a hot-tapped installation and maintenance. (Special order of custom-made)
Output:4-20mA,Pulse,OCT
Communication:RS485
Transmitter working temperature:-10~70¡æ
Sensor wotking temperature:-30~150¡æ
Power supply:DC24V,AC220V

Thernal gas flow meter is one kind smart gas flow instrument, It can easily and accurately detect the mass flowrate of gas,specical for low flowrate.
They have an impressively high accuracy, short response time and a very wide flow range with virtually no loss of accuracy even at the lowest flow rates.
Accuracy:¡À1.0 %
4-20mA is Optical isolation
Body material:Standard carbon steel,SS304 and SS316 are optional

Natural gas thermal gas mass flow meter is one of kind mass flow meter which is popular in industrial applications is the way they are designed and built. The feature is no moving parts, nearly unobstructed straight through flow path, require no temperature or pressure corrections and retain accuracy over a wide range of flow rates.
Media:All gas except acetylene and humid gas
Measure range:1:100
Sesnsor working temperature:-20~220℃
Transmitter working temperature:-20~45℃
Output:4-20mA

Thermal gas mass flow meter with LCD display,can display volume flow rate,mass flow rate,
total flow and temperature.
Insertion type thermal gas mass flow meter accuracy is 1.5%
Inline type thermal gas mass flow meter accuracy is 1.0%

Natural gas thermal mass flow meters measure the mass flowrate of fluids by measuring the heat conducted from a heated surface to the flowing fluid. Since a flowing fluid removes a known quantity of heat as it passes, the temperature difference between the heated sensor and the flow stream is directly proportional to the mass flow rate.
With RS485 or HART communication
Power supply:24VDC ,220VAC
Accuracy:¡À1.0%~¡À1.5%

Except for acetylene,thermal gas mass flowmeters can measure various of dry gas.
Such as Air, Natrual gas, N2, O2, CO2 etc.When measure the flammable and explosive gas,the flow meter need with ex-proof function.
24VDC will better and safety

The thermal gas flowmeter is mainly used for measuring gas with low flow and the range could reach 1:100,which is btter than gas flowmeter on market and low flow could be measured,the min.flow velocity can reach 0.1Nm/s and Max. velocity reach 100Nm/s
Media:All gas except acetylene and humid gas
Measure range:1:100
Sesnsor working temperature:-20~220℃
Transmitter working temperature:-20~45℃
Output:4-20mA

Thermal flow meter is one kind of gas mass flow meter, can display mass flow rate and total mass flow
According to request, Q&T can do OEM ,such as display converter color,Display LOGO,Flow unit etc.
Output is 4-20mA,Pulse
Communication is RS485 or HART

Thermal mass flow meter is precision instruments that can directly measure mass flow,such as industrial gases, compressed gas, and other gases.
Gas thermal mass flow meter body is be made by stainless steel and stainless steel is more durable and better air tightness.
DC4-20mA four-wire output
Mass flow unit
Dual power:24VDC,220VAC
Min.Flow veloctiy:0.1Nm/s
Output:4-20mA

Q&T gas mass thermal flow meters are be calibrated by gas venturi sonic nozzle calibration device,and ensure the thermal gas mass flowmeter accuracy can reach 1.0% and 1.5%.
When calibrate thermal flow meter,Q&T will choose four flow velocity points ,then calibrate 3 times each velocity point
Media:All gas except acetylene and humid gas
Measure range:1:100
Sesnsor working temperature:-20~220℃
Transmitter working temperature:-20~45℃
Output:4-20mA

Insertion type thermal flow meter which be used to measure the air flow velocity.
Air velocity thermal flow meter with widely flow range and flow ratio can reach 1:100.
Measuring tube dia. is ¦Õ12mm and ball valve is 1/2″ NPT
24VDC power supply its more safety for gas.

Thermal gas flowmeter is mainly used for measuring gas with low flow and the range could reach 1:100,which is btter than gas flowmeter on market and low flow could be measured,the min.flow velocity can reach 0.1Nm/s and Max. velocity reach 100Nm/s
Volume flow /Mass flow

Q&T thermal gas mass flow meter with DC4-20mA four-wire output,which is more convenient for remote reception.Support MODBUS RTU RS485 protocol,coordinating the receiving system to collect more data ans modify system
Media:All gas except acetylene and humid gas
Measure range:1:100
Sesnsor working temperature:-20~220℃
Transmitter working temperature:-20~45℃
Output:4-20mA
Accuracy:±1.0%~±2.5%
Probe material:SS316L
Power supply:24VDC ,220VAC
Response time:1S
Display:4 line digital

Thermal gas mass flow meter mainly measure various of gases ,special dry gases,but thermal gas mass flow meter can’t measure acetylene.
In many applications, the thermal properties of the fluid can be dependent upon fluid composition. In such applications, varying composition of the fluid during actual operation can affect the thermal flow measurement. Therefore, it is important for the thermal flow meter supplier to know the composition of the fluid so that the proper calibration factor can be used to determine the flow rate accurately
Widly flow range ratio:1:100
Display:4 line digital
With RS485 or HART communication
Power supply:24VDC ,220VAC
Accuracy:¡À1.0%~¡À1.5%

Thermal gas mass flow meter with DC4-20mA four-wire output,which is more converient for remote reception.Support MODBUS RTU RS485 protocol,coording the receiving system to collect more data and modify system and Q&T brand thermal gas mass flow meter already got CE ,Ex-Proof certificates
Pressure:
Insertion type¡Ü1.6Mpa
Flange type ¡Ü4.0Mpa

Thermal gas mass flowmeter’s medium temperature range of meter is -40¡æ¡«220¡æ.
When the gas is very humid or saturated with water (e. g. Bio Gas), the piping and flowmeter body should be insulated to prevent water droplets condensing on the measuring sensor.
Insertion type:DN32~DN4000
Flange type:DN10~DN300
Tri-clamp type :DN10~DN100
Thread type:DN10~DN100

Thermal gas mas flow meters are measuring the mass flow or volume flow of gas,flow range can do 0.5Nm/s¡«100Nm/s. So this meter also can be used for gas leak detection.
Thermal flow sensor temp is always 30¡æ higher than the medium temperature (environment temperature), and the meter adopts method of constant differential temperature, therefore the meter don¡¯t need temperature and pressure compensation in principle.

Thermal gas mass flow meter for pipe dia. DN10~DN2000 and is precision instrument that directly measure gas.
Themal mass flow meter have widely turndown ratio 1:100,so this flow meter is advantage for low flowrate and can be used to detect leak.
SUS304 body
MODBUS RTU RS485
0.1~100Nm/s
4 lines LCD
EX-PROOF

For the insertion type instrument, on the premise that both the measuring media and field environment are applicable for online dismantlement with non-stop operation, it is viable to have maintenance operation with non-stop operation relying on its special structure
Media:All gas except acetylene and humid gas
Measure range:1:100
Sesnsor working temperature:-20~220℃
Transmitter working temperature:-20~45℃
Output:4-20mA

Thermal gas mass flow emter be widely used in the process control and gas flow measurement of petroleum, chemical industry, metallurgy, electric power, water treatment, papermaking, food, medicine, cement, textile and various production and scientific research institutions.
Natural gas thermal gas mass flow meter can reach 1.0% accuracy and has been calibrated by a third-party laboratory.
Dual power:24VDC,220VAC
Min.Flow velocity:0.1Nm/s
Online installation

Thermal mass flow meters are used frequently in monitoring or controlling mass-related processes and measuring range can reach 1:100
So thermal mass flow meters are most often used for the regulation of low gas flowrate.
Media:All gas except acetylene and humid gas
Measure range:1:100
Sesnsor working temperature:-20~220℃
Transmitter working temperature:-20~45℃
Output:4-20mA

Insertion thermal gas mass flow meter with anti flush-out design for high pressure,more safety
When absolute pressure of measuring medium is higher than 5 times standard atmospheric pressure, or higher than the pressure of possible danger, should shut down or do reducing pressure to reach a safety pressure, and then do hot-tapped operation. If there are no conditions to do hot-tapped operation, should shut down to avoid dangers.

LCD display thermal gas flow meter is a meter that uses the principle of heat transfer to detect flow.
The thermal gas flow meter is available in high-performance pipeline type and insert type flow meter. Insert flow meter consist of a probe with sensing elements that are inserted into the pipe irrespective of pipe size. These are easy to install and more economical. Inline flow meters are connected to the pipe itself by the flanged or threaded connection. Inline meters are suitable for smaller diameter pipes.

Thermal mass flowmeters are suitable for all industrial and test rig applications that demand quick and precise gas measurement.
Thermal air mass flow meter be adopted the critical flow nozzle calibration device to calibrate each gas mass flow meter,the calibration device flow range can reach Min. 0.5m3/h and Max.10000 m3/h .
Widely turndown ratio:100:1
Power supply:24VDC&220VAC
Response time:1S

Split display insert thermal gas mass flow meter is one kind of competitive gas flow meter for natrual gas industry
Easy installation, simple maintenance, two-way detection, anti-vibration
Flow measurement up to 24 points,and its suitable for low flow measurement ,so thermal gas mass flow meter can be used for leak detection