4~20mA Output Water Flow Meter 1inch Turbine Water Flow Meter

turbine flowmeter advantage
1.High accuracy, generally up to ¡À1%R, ¡À0.5%R, high accuracy up to 0.2%R
2.Good repeat-ability, short-term repeat-ability up to 0.05% ~ 0.2%, in the trade settlement is the preferred choice of flow meter.
3.Output of pulse frequency signal, suitable for totalizer and connection with PC; no zero shift and strong interference resist
4.High frequency signal(3~4KHz) can be obtained, the signal resolution is strong.
5.Wide range, medium and large diameter up to 1:20, small caliber 1:10.

A turbine flow meter is a volumetric metering the meter consists of a rotor and bearing assembly Suspended on a shaft, which is mounted to a support device.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%;
OUTPUT: PULSE/4-20mA;
Digital Communication:RS485, MODBUS; HART

A turbine flow meter is a volume sensing device. As liquid or gas passes through the turbine housing, it causes the freely suspended turbine blades to rotate. The velocity of the turbine rotor is directly proportional to the velocity of the
Turbine flowmeters are widely used in the following measurement objects: petroleum, organic liquids, inorganic liquids, liquefied gas, natural gas, coal gas and cryogenic fluids. It is widely used in foreign transshipment and gathering stations of liquefied petroleum gas, refined oil and light crude oil, as well as the first and last stations of large crude oil pipelines for trade settlement.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%/¡À0.2%;
OUTPUT: PULSE/4-20mA;
Digital Communication:RS485, MODBUS; HART

A turbine flowmeter is a flowmeter that uses a turbine for measurement. It first converts the flow rate to the speed of the turbine. And then converts the speed into an electrical signal that is proportional to the flow.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%;
OUTPUT: PULSE+4-20mA;
Digital Communication:RS485, MODBUS; HART

QTLL series gas roots flow meter is is a high-quality positive displacement roots-type gas meter which is available in an assortment of sizes and options. Based on the principle of volumetric measurement, rotary gas meter is used to accurately measure the gas flow through a closed pipeline.
Size:DN25-200mm
Material:Aluminum alloy or stainless steel
Dual Power:3.6V battery powered+DC24V
Output:4-20mA,Pulse,RS485
Installation: Vertical or Horizontal
Accuracy:1.5% or 1.0%

Turbine Flowmeters are the optimum combination of useful range, corrosion resistance, and operating life for a particular application. A low mass rotor design allows for a rapid dynamic response which permits the turbine flowmeter to be used in pulsating flow applications.

QTWG Turbine gas meter volume measuring instruments for gaseous media and operate according to the displacement principle. They register the gas volume under working conditions. In order to correct the measured value to the standard volume, electronic volume correctors can be used.Turbine gas meters deliver high accuracy in gas flow measurements, which could highly inrease the efficiency in various custody transfer applications.

Size:DN25-400mm
Material:Aluminum alloy or stainless steel
Dual Power:3.6V battery powered+DC24V
Output:4-20mA,Pulse,RS485
Accuracy:1.5% or 1.0%

QTWG series turbine gas meter is an ideal flow instrument to measure natural gas in industrial and commercial billing applications. Natural gas flow meters provide various kinds of outputs including 4-20mA, pulse and RS485 easily connect into user control systems.

Size:DN25-400mm
Material:Aluminum alloy or stainless steel
Dual Power:3.6V battery powered+DC24V
Output:4-20mA,Pulse,RS485
Accuracy:1.5% or 1.0%

The turbine flow meter accuracy plays an important role in the floating measurement process of the rotor. So the high-precision turbine flowmeter has almost no resistance during the floating measurement process of the rotor, thereby ensuring the high precision, linearity and durability of the turbine flowmeter.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%/¡À0.2%;
OUTPUT: PULSE/4-20mA;
Digital Communication:RS485, MODBUS; HART

QTLL series gas roots flow meter adopt high-strength aluminum alloy waist wheel, corrosion resistance and long service life,
Rotary gas meters are designed to meet the highest demands of reliable and accurate measurement of gas flow. Based on the principle of volumetric measurement, rotary gas flow meter is used to accurately measure the gas flow through a closed pipeline.
Size:DN25-200mm
Material:Aluminum alloy or stainless steel
Dual Power:3.6V battery powered+DC24V
Output:4-20mA,Pulse,RS485
Installation: Vertical or Horizontal
Accuracy:1.5% or 1.0%

Turbine Flow Meter is a volumetric measuring turbine type of Impeller Flowmeters, made up of sensors and Convertor. The flowing fluids engage the rotor causing it to rotate at an angular velocity proportional to the fluid flow rate. The Sensor reacts to the average velocity of fluid with the multi-blades rotor so as to speculating the flow value and the accumulative flow value
liquid turbine flow meter is a volumetric metering the meter consists of a rotor and bearing assembly Suspended on a shaft, which is mounted to a support device.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%/¡À0.2%;
OUTPUT: PULSE/4-20mA;
Digital Communication:RS485, MODBUS; HART

turbine Flow meter for diesel is specially designed for usage in water, alcohol, diesel, gasoline and other fluid measurement and control systems. They operate according to the turbine principle, i.e. the speed of an impeller turning in the fluid flow is measured and converted into pulse or 4-20mA signals.

QTLL series rotary gas meters adopt high-precision digital temperature sensor, digital pressure sensor.
Gas rotary meter with the features of high accuracy, high sensitivity and long working life. Rotary gas meters with multiple outputs which could reach the requirements of most work sites.
Size:DN25-200mm
Material:Aluminum alloy or stainless steel
Dual Power:3.6V battery powered+DC24V
Output:4-20mA,Pulse,RS485
Installation: Vertical or Horizontal
Accuracy:1.5% or 1.0%

Turbine meters measure flow using the mechanical energy of the fluid or gas to rotate a turbine rotor within the flow stream inside the meter. The rotations are measured and calculated to provide a proportional measurement relative to flow rate. The Principle is well proven and the application suitability list is very large.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%/¡À0.2%;
OUTPUT: PULSE/4-20mA;
Digital Communication:RS485, MODBUS; HART

turbine flow meter is a new generation of turbine flow meters with the advantages of simple structure, light weight, high precision, good reproducibility, sensitive response, convenient installation, maintenance and use. It is widely used. It is not corrosive to stainless steel 1Cr18Ni9Ti, 2Cr13, corundum Al203 and cemented carbide in the measurement of closed pipelines, and there is no fiber, particles and other impurities. The kinematic viscosity of the liquid is less than 5*10-6©O/s at working temperature. For the kinematic viscosity For liquids larger than 5*10-6©O/s, the flow meter can be used after real liquid calibration. If matched with a display instrument with special functions, it can also be used for quantitative control, overweight alarm, etc., an ideal instrument for flow measurement and energy saving.

preprocess applications.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%/¡À0.2%;
OUTPUT: PULSE/4-20mA;
Digital Communication:RS485, MODBUS; HART

Liquid turbine flow meter having a mechanical section combined with electronic board displaying the flow rate, the end connection of which is finished with a flange. Because its driving part is mechanical, it can be applied for all fluids of low temperature to high temperature with relatively high accuracy and excellent reproducibility.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%/¡À0.2%;
OUTPUT: PULSE/4-20mA;
Digital Communication:RS485, MODBUS; HART

QTWG series turbine gas meters are designed to measure natural gas, air,propane and other clean gases. Turbine gas meters
provide high-quality natural gas measurement which could increase efficiency in boiler/burner control and custody transfer applications.
Size:DN25-400mm
Material:Aluminum alloy or stainless steel
Dual Power:3.6V battery powered+DC24V
Output:4-20mA,Pulse,RS485
Accuracy:1.5% or 1.0%

QTWG turbine gas flow meters are ideal flow measurement device for clean gas, including natural gas, LPG gas etc. Turbine gas meters are with lightweight in compact body and support a wide range of measurement including maximum working pressure and maximum measuring flow rate.
Size:DN25-400mm
Material:Aluminum alloy or stainless steel
Dual Power:3.6V battery powered+DC24V
Output:4-20mA,Pulse,RS485
Accuracy:1.5% or 1.0%

turbine flowmeter is a kind of speed flowmeter. The sensor of turbine flow meter has the advantages of simple structure, lightweight, high precision, good reproducibility and quick response. It is widely used in petroleum, chemical industry, metallurgy, water supply, papermaking and other industries. It is the best choice for flow measurement and energy saving.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%;
OUTPUT: PULSE+4-20mA;
Digital Communication:RS485, MODBUS; HART
LCD display

turbine flow sensor are simple structure, Lightweight, high accuracy, good repeatability, sensitive reaction, low installation and maintenance£¬ Easy to use and so on,it is used in petroleum, chemical, metallurgy, water, paper and other industries, Is to measure the energy flow measurement and instrumentation of the ideal
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%/¡À0.2%;
OUTPUT: PULSE/4-20mA;
Digital Communication:RS485, MODBUS; HART

Turbine Flowmeters draw the leading technology integrating with advanced design to produce the new generation of turbine flowmeter with the features of simple structure, light weight, high accuracy, good repeatability, flexible reaction, convenient installation/maintenance/application etc.. It is widely applied to measuring the liquid of which kinematic viscosity is under 5*10-6©O/s and have no impurify of fibre,grain etc.,and no corrosive interaction with the stainless steel 1Cr18Ni9Ti,2Cr13,and A12O3, and hard alloy in seal pipes
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%;
OUTPUT: PULSE+4-20mA;
Digital Communication:RS485, MODBUS; HART
LCD display

QTWG series gas turbine flow meters are are designed to measure natural gas, propane and other non-corrosive gases for large volume commercial and industrial uses. Q&T turbine gas meters could guarantee exact values for commercial and non-commercial measurements.?
Size:DN25-400mm
Material:Aluminum alloy or stainless steel
Dual Power:3.6V battery powered+DC24V
Output:4-20mA,Pulse,RS485
Accuracy:1.5% or 1.0%

turbine flow transducer adapts to measure the liquid rate and total flowrate of low viscosity. It can be widely used in the fields of Petrol, Chemical industry, Metallurgy, Scientific research for measuring or control. Several output and display methods can be selected.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%;
OUTPUT: PULSE+4-20mA;
Digital Communication:RS485, MODBUS; HART

Turbine flow metera flow meter that widely applied in industries of pharmaceutical, food, beverage for measurement, batching, control, filling, etc. Rotating part of the flow meter is made of special material that possesses good anti-corrosive and rust proof performance. Structure of the flow meter is special designed and greatly approved accuracy and repeatability of the flow meter. Product also with easy maintenance connection, which is suitable for pharmaceutical and beverage industries

turbine Flow meter wide working temperature and pressure range, it is capable of measuring various mediums and commissioning into extreme working conditions. Flow meter for diesel are popular in the Oil & Gas industry, Chemical industry, and Water industry.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%/¡À0.2%;
OUTPUT: PULSE/4-20mA;
Digital Communication:RS485, MODBUS; HART

Turbine Flow Meter is a main type of Impeller Flowmeter also including the Anemoscope and Water meter.it is made up of Sensor and Conversion-Show. The Sensor reacts to the average velocity of fluid with multi-blades rotor so as to speculating the flow value and the accumulative flow value.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%;
OUTPUT: PULSE+4-20mA;
Digital Communication:RS485, MODBUS; HART

QTWG series gas turbine flow meters are with the feature of integrated design, big LCD windows, which are easy to debug and monitor.
Turbine gas meters could be separately used for gas that is clean,low viscosity,such as Air, Natural gas, LPG, Methane gas, Ar, CO2 etc. Q&T turbine gas meters could guarantee exact values for commercial and non-commercial measurements.?
Size:DN25-200mm
Material:Aluminum alloy or stainless steel
Dual Power:3.6V battery powered+DC24V
Output:4-20mA,Pulse,RS485
Installation: Vertical or Horizontal
Accuracy:1.5% or 1.0%

QTWG Turbine gas meter is a popular device for gas-fired, gas pipeline network and city gas field etc. QTWG gas turbine meters are very reasonably priced with good reliability and quality. Widely used in gas measuring from Petroleum, Chemical, Electric power,Industrial boiler etc.
Size:DN25-400mm
Material:Aluminum alloy or stainless steel
Dual Power:3.6V battery powered+DC24V
Output:4-20mA,Pulse,RS485
Accuracy:1.5% or 1.0%

Turbine flow meters are simple and reliable. They are able to measure high flow rates with low-pressure loss. Though versatile, turbine meters do best in applications with constant conditions in liquids such as water or lower viscosity fluids.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%;
OUTPUT: PULSE+4-20mA;
Digital Communication:RS485, MODBUS; HART

Turbine Flowmeter’s advantages : simple structure , less processing components, light weight, convenient maintenance, is the general type of flowmeter, superior performance, high precision, anti magnetic interference, 540 rotating convenient reading
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%;
OUTPUT: PULSE+4-20mA;
Digital Communication:RS485, MODBUS; HART
LCD display