4 Inch Pipeline Sanitary Food Application Turbine Flowmeter for Milk Beverage

QTWG series intelligent explosion proof turbine gas meters are designed to measure natural gas, air,propane and other clean gases. Natural gas turbine meters provide very accurate flow monitoring.?Has an good ability to provide fast response to changing flow rates with consistent accuracy.
Size:DN25-400mm
Material:Aluminum alloy or stainless steel
Dual Power:3.6V battery powered+DC24V
Output:4-20mA,Pulse,RS485
Accuracy:1.5% or 1.0%

Turbine flow meters are mechanical meters that have a freely rotating turbine set in the path of a fluid stream. The flowing liquid or gas causes the turbine to spin upon its axis. The rate of spin will be proportional to the velocity of the flow. Turbine flow meters are simple and reliable.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%;
OUTPUT: PULSE+4-20mA;
Digital Communication:RS485, MODBUS; HART

Natural gas flow meter is used to measure gas flow, with the features of high accuracy, low-pressure drop. Gas turbine flow meter provides high-quality natural gas measurement which could increase efficiency in boiler/burner control, fuel-to-air ratio, and custody transfer applications.
Size:DN25-400mm
Material:Aluminum alloy or stainless steel
Dual Power:3.6V battery powered+DC24V
Output:4-20mA,Pulse,RS485
Accuracy:1.5%/1.0%

QTWG series natural gas flow meter is used to measure gas flow, with the features of high accuracy, low-pressure drop. Wide turndown gas turbine flow meter is custody transfer approval flow meter, widely used in clean gas including natural gas, LPG gas etc.
Size:DN25-200mm
Material:Aluminum alloy or stainless steel
Dual Power:3.6V battery powered+DC24V
Output:4-20mA,Pulse,RS485
Installation: Vertical or Horizontal
Accuracy:1.5% or 1.0%

Turbine Flow Meters are useful for liquids & gases in general industrial application. They provide excellent performance with quality & reliability. Suitable for as hygienic application. The flowing media engages a vaned rotor causing it to rotate at an angular velocity proportional to flow rate. The pick -of coil senses the spinning motion of the rotor inside the pipe & converts it into a pulsating electrical signal. Summation of the pulsating electrical signal is directly related to the total flow. The frequency is linearly proportional to flow rate which is converted to mA signal by electronic circuitry. Flow rate Indicator / Totalizer / Transmitter and Controllers are available in Local/Remote and Panel Mounted Options.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%/¡À0.2%;
OUTPUT: PULSE/4-20mA;
Digital Communication:RS485, MODBUS; HART

Turbine flowmeter measures the flowrate from the number of revolutions of a blade placed in the flow. The speed of revolutions of the blade with an axis parallel to the flow direction is proportional to the speed of the flow.the turbine flowmeter is useful for process control, transactions as well as process control of petroleum products, general chemical fluids, liquefied gas, water, etc.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%/¡À0.2%;
OUTPUT: PULSE/4-20mA;
Digital Communication:RS485, MODBUS; HART

Turbine flow sensor is a precision flow measuring instrument, which can be used to measure the flow and total amount of liquid together with the corresponding flow totalizer. It is widely used in metering and control systems in petroleum, chemical, metallurgy, scientific research and other fields. Turbine flow sensors with sanitary fittings can be used in the pharmaceutical industry.
The structure of the integrated turbine flowmeter is explosion-proof and can display the total flow, instantaneous flow and percentage of full flow. The battery adopts long-term lithium battery. The battery life of the single-function accumulator can reach more than 5 years, and the battery life of the multi-function display watch can also reach more than 12 months.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%/¡À0.2%;
OUTPUT: PULSE/4-20mA;
Digital Communication:RS485, MODBUS; HART

The turbine flow meter accuracy plays an important role in the floating measurement process of the rotor. So the high-precision turbine flowmeter has almost no resistance during the floating measurement process of the rotor, thereby ensuring the high precision, linearity and durability of the turbine flowmeter.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%/¡À0.2%;
OUTPUT: PULSE/4-20mA;
Digital Communication:RS485, MODBUS; HART

turbine flow meter is a volumetric metering the meter consists of a rotor and bearing assembly Suspended on a shaft, which is mounted to a support device.
This assembly is mounted inside a housing of a calibrated internal diameter. As fluid passes through the flow meter housing, the rotor will spin at a rate proportional to the volume of liquid passing through the housing. A magnetic or modulated pick-off sensor is used to detect the passage of each rotor blade and generate a frequency output. The frequency output can be read directly with the end users electronics or further processed to convert to a linear analog flow Rate output.

preprocess applications.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%/¡À0.2%;
OUTPUT: PULSE/4-20mA;
Digital Communication:RS485, MODBUS; HART

Turbine flowmeter is widely used in the following measurement objects: petroleum, organic liquid, inorganic liquid, liquefied gas, natural gas, coal gas and cryogenic fluid.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%;
OUTPUT: PULSE+4-20mA;
Digital Communication:RS485, MODBUS; HART
LCD display

turbine Flow meter wide working temperature and pressure range, it is capable of measuring various mediums and commissioning into extreme working conditions. Flow meter for diesel are popular in the Oil & Gas industry, Chemical industry, and Water industry.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%/¡À0.2%;
OUTPUT: PULSE/4-20mA;
Digital Communication:RS485, MODBUS; HART

QTLL series gas roots flow meter is an instrument for accurately measuring gas flow. Based on the principle of
volumetric measurement, gas roots flow meter is used to accurately measure the gas flow through a closed pipeline. Rotary gas meter has high precision, wide range, small size, light weight, convenient installation and maintenance, reliable use and Durable service life
Size:DN25-200mm
Material:Aluminum alloy or stainless steel
Dual Power:3.6V battery powered+DC24V
Output:4-20mA,Pulse,RS485
Installation: Vertical or Horizontal
Accuracy:1.5% or 1.0%

The turbine flow meter is suitable for a wide range of viscosity medium including oil, gas, water and wastewater, chemical, gas utility, power, food and beverage, aerospace, pharmaceutical, etc.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%;
OUTPUT: PULSE+4-20mA;
Digital Communication:RS485, MODBUS; HART
LCD display

Turbine Flow Meter is a volumetric measuring turbine type of Impeller Flow meters , made up of Sensor and Convertor. The flowing fluids engages the rotor causing it to rotate at an angular velocity proportional to the fluid flow rate.The Sensor reacts to the average velocity of fluid with multi-blades rotor so as to speculating the flow value and the accumulative flow value.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%;
OUTPUT: PULSE+4-20mA;
Digital Communication:RS485, MODBUS; HART
LCD display

QTWG series gas turbine flow meters are with the feature of integrated design, big LCD windows, which are easy to debug and monitor.
Turbine gas meters could be separately used for gas that is clean,low viscosity,such as Air, Natural gas, LPG, Methane gas, Ar, CO2 etc. Q&T turbine gas meters could guarantee exact values for commercial and non-commercial measurements.?
Size:DN25-200mm
Material:Aluminum alloy or stainless steel
Dual Power:3.6V battery powered+DC24V
Output:4-20mA,Pulse,RS485
Installation: Vertical or Horizontal
Accuracy:1.5% or 1.0%

The turbine flow meter is an ideal solution when high accuracy, compact size, fast response, and high tolerance to shock and vibration are critical requirements and suitable for wide range of viscosity medium including oil, gas, water and wastewater, chemical, gas utility, power, food and beverage£¬pharmaceutical, etc.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%;
OUTPUT: PULSE+4-20mA;
Digital Communication:RS485, MODBUS; HART

QTWG series turbine gas meter is designed to perform on the high level of accuracy, which is an ideal product for commercial and industrial uses. All the measured values can be displayed and are available on the modbus interface.

Size:DN25-400mm
Material:Aluminum alloy or stainless steel
Dual Power:3.6V battery powered+DC24V
Output:4-20mA,Pulse,RS485
Accuracy:1.5% or 1.0%

Turbine Flowmeters draw the leading technology integrating with advanced design to produce the new generation of turbine flowmeter with the features of simple structure, light weight, high accuracy, good repeatability, flexible reaction, convenient installation/maintenance/application etc.. It is widely applied to measuring the liquid of which kinematic viscosity is under 5*10-6©O/s and have no impurify of fibre,grain etc.,and no corrosive interaction with the stainless steel 1Cr18Ni9Ti,2Cr13,and A12O3, and hard alloy in seal pipes
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%;
OUTPUT: PULSE+4-20mA;
Digital Communication:RS485, MODBUS; HART
LCD display

Turbine flowmeter measures the flowrate from the number of revolutions of a blade placed in the flow. The speed of revolutions of the blade with an axis parallel to the flow direction is proportional to the speed of the flow. Utilizing the capability of highly accurate measurement for wide range of viscosity, the turbine flowmeter is useful for process control, transactions as well as process control of petroleum products, general chemical fluids, liquefied gas, water, etc.
In addition to the model for liquid, models dedicated to saturated steam measurement are also available.

QTWG series gas turbine flow meters are with the feature of integrated design, big LCD windows, which are easy to debug and monitor.
Turbine gas meters provide consistently consistently accurate results in measuring clean gas within a variety of applications.
Size:DN25-400mm
Material:Aluminum alloy or stainless steel
Dual Power:3.6V battery powered+DC24V
Output:4-20mA,Pulse,RS485
Accuracy:1.5% or 1.0%

Works well with Low viscosity liquids. The turbine turns when the good passes through and a pulsed counter provides the flow total on a digital display
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%/¡À0.2%;
OUTPUT: PULSE/4-20mA;
Digital Communication:RS485, MODBUS; HART

turbine flow meter is a new generation of turbine flow meters with the advantages of simple structure, light weight, high precision, good reproducibility, sensitive response, convenient installation, maintenance and use. It is widely used. It is not corrosive to stainless steel 1Cr18Ni9Ti, 2Cr13, corundum Al203 and cemented carbide in the measurement of closed pipelines, and there is no fiber, particles and other impurities. The kinematic viscosity of the liquid is less than 5*10-6©O/s at working temperature. For the kinematic viscosity For liquids larger than 5*10-6©O/s, the flow meter can be used after real liquid calibration. If matched with a display instrument with special functions, it can also be used for quantitative control, overweight alarm, etc., an ideal instrument for flow measurement and energy saving.

preprocess applications.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%/¡À0.2%;
OUTPUT: PULSE/4-20mA;
Digital Communication:RS485, MODBUS; HART

turbine flowmeter can be applied to alcohol, toluene, etc. which are not electrically conductive. And it can be used also in oil and gas, power plants, pharmaceutical and pulp & paper-making industry. However, it is recommended to not use for fluids containing sludge or highly viscous fluids. Also, it can be provided in flange type or screw (male or female) type while being able to cope with various piping conditions.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%/¡À0.2%;
OUTPUT: PULSE/4-20mA;
Digital Communication:RS485, MODBUS; HART

turbine Flow meter for diesel is specially designed for usage in water, alcohol, diesel, gasoline and other fluid measurement and control systems. They operate according to the turbine principle, i.e. the speed of an impeller turning in the fluid flow is measured and converted into pulse or 4-20mA signals.

QTWG Turbine gas meter is a popular device for gas-fired, gas pipeline network and city gas field etc. Turbine gas meters deliver high accuracy in gas flow measurements, which could highly inrease the efficiency in various custody transfer applications.

Size:DN25-400mm
Material:Aluminum alloy or stainless steel
Dual Power:3.6V battery powered+DC24V
Output:4-20mA,Pulse,RS485
Accuracy:1.5% or 1.0%

turbine Flowmeter is designed for usage in water, diesel, gasoline and other fluid measurement and control systems. They operate according to the turbine principle, the speed of an impeller turning in the fluid flow is measured and converted into pulse or 4-20mA signals.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%;
OUTPUT: PULSE+4-20mA;
Digital Communication:RS485, MODBUS; HART
LCD display

A turbine flow meter is used for volumetric total flow &/or flow rate measurement & has a relatively simple working principle. As fluid flows through the turbine meter, it impinges upon turbine blades that are free to rotate about an axis along the center line of the turbine housing. The angular (rotational) velocity of the turbine rotor is directly proportional to the fluid velocity flowing through the turbine. The resulting output is taken by an electrical pickoff(s) mounted on the flow meter body.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%/¡À0.2%;
OUTPUT: PULSE/4-20mA;
Digital Communication:RS485, MODBUS; HART

Turbine Flow Meter is a main type of Impeller Flowmeter also including the Anemoscope and Water meter. it is made up of Sensor and Conversion-Show. The Sensor reacts to the average velocity of fluid with multi-blades rotor so as to speculating the flow value and the accumulative flow value. The velocity (or circles) of rotor can be picked up by the way of mechanism, electromagnetic induction, photo electricity, before displaying and transmitting the records by reading device.

turbine flowmeter is a kind of speed flowmeter. The sensor of turbine flow meter has the advantages of simple structure, lightweight, high precision, good reproducibility and quick response. It is widely used in petroleum, chemical industry, metallurgy, water supply, papermaking and other industries. It is the best choice for flow measurement and energy saving.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%;
OUTPUT: PULSE+4-20mA;
Digital Communication:RS485, MODBUS; HART
LCD display

liquid turbine flow meter, is a precision flow measuring instrument,that can be used to measure the flow and total volume of liquids. The structure is explosion-proof and can show the total flow, instantaneous flow and percentage of flow fullness. It is widely used in measurement and control systems in petroleum, chemical, metallurgical, scientific research and other fields. Sensors equipped with sanitary fittings can be used in the pharmaceutical industry.