24DC power supply turbine flowmeter monitor display liquid flow meter

QTWG turbine gas meter is a type of high-precision custody transfer metering. As a ideal flow measurement device for natural gas or other non-corrosive gases applications, gas turbine flow meter urbine could be automatically pressure and temperature compensation to obtain volumetric measurements in standard units.

Size:DN25-400mm
Material:Aluminum alloy or stainless steel
Dual Power:3.6V battery powered+DC24V
Output:4-20mA,Pulse,RS485
Accuracy:1.5% or 1.0%

turbine flow meter is available in a wide range of body sizes and styles to suit liquid flow applications for low to medium viscosity fluids.
The principle of operation is based on a permanent magnet contained within a pick-off coil on the body and a ferritic stainless steel rotor which revolves when flow is present. A small AC voltage is generated in the coil as the rotor tip passes the magnet. The frequency of this AC voltage is directly proportional to the flow rate. The total number of pulses produced represents the total flow passed through the meter.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%/¡À0.2%;
OUTPUT: PULSE/4-20mA;
Digital Communication:RS485, MODBUS; HART

The turbine flowmeter is common flow meter. It is one of the most precise and reproducible flow meters. Turbine meters have a fairly high flow rate, good long-term and short-term repeatability, and are usually linear above the first 10 to 20% of the flow rate.
Turbine meters evaluate stream speed by counting a rotor¡¯s amount of revolutions spinning as the fluid passes through its blades.
The meter may contain an electronic detector that divides a rotor revolution into pulses. The readout records the variables and transforms them into a separate variable recognized as the reference Pulse Factor or ¡°K-factor¡± into the specified volume stream speed.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%/¡À0.2%;
OUTPUT: PULSE/4-20mA;
Digital Communication:RS485, MODBUS; HART

QTWG series turbine gas flow meters are designed to measure natural gas, air,propane and other clean gases in industrial and commercial billing applications. Gas turbine meters provide fast response to changing flow rates with consistent accuracy and various kinds of outputs including 4-20mA, pulse and RS485.

Size:DN25-400mm
Material:Aluminum alloy or stainless steel
Dual Power:3.6V battery powered+DC24V
Output:4-20mA,Pulse,RS485
Accuracy:1.5% or 1.0%

A turbine flow meter is used for volumetric total flow &/or flow rate measurement & has a relatively simple working principle. As fluid flows through the turbine meter, it impinges upon turbine blades that are free to rotate about an axis along the center line of the turbine housing. The angular (rotational) velocity of the turbine rotor is directly proportional to the fluid velocity flowing through the turbine. The resulting output is taken by an electrical pickoff(s) mounted on the flow meter body.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%/¡À0.2%;
OUTPUT: PULSE/4-20mA;
Digital Communication:RS485, MODBUS; HART

turbine flow meter refers to the turbine flow sensor with 50mm size. DN50 turbine flow meter can be used to take volumetric flow measurement of petroleum, organic liquid, biogas, LPG gas, liquefied gas, natural gas, hydrocarbon gas, nitrogen, cryogenic fluid, water, diesel, High-pressure hydraulic oil, methanol and other non-impurity, non-corrosive. 2 inch turbine flow meter has many applications in turbine heating systems, boilers measurement of water supply, heat exchange system, air conditioning circulating water, etc.

QTWG turbine gas flow meters are designed to accurately measure natural gas, air, nitrogen, carbon dioxide, propane vapor, and other non-corrosive gases for large volume commercial and industrial uses. they are ideal flow measurement device for clean gas, including natural gas, LPG gas etc. With user-friendly display, support of flowrate, temperature, pressure each in operating and standard status. Turbine gas meters support a wide range of measurement including maximum working pressure and maximum measuring flow rate.

Size:DN25-400mm
Material:Aluminum alloy or stainless steel
Dual Power:3.6V battery powered+DC24V
Output:4-20mA,Pulse,RS485
Accuracy:1.5% or 1.0%

Turbine flowmeters are flow measurement instruments which use axial fluid momentum to turn a multibladed rotor, the angular velocity of which is approximately proportional to the volume flowrate. With appropriate calibration and operation, turbine meters offer precise and highly repeatable measurement of throughput and flowrate.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%;
OUTPUT: PULSE/4-20mA;
Digital Communication:RS485, MODBUS; HART

QTWG series wide turndown gas turbine flow meters are custody transfer approved flow meters, widely used in clean gas including natural gas, LPG gas etc. Q&T gas turbine flow meters are well manufactured and tested in factory which could ensure exact values for fiscal and non-fiscal measurements.?
Size:DN25-400mm
Material:Aluminum alloy or stainless steel
Dual Power:3.6V battery powered+DC24V
Output:4-20mA,Pulse,RS485
Accuracy:1.5% or 1.0%

Turbine Flow Meter is a main type of Impeller Flowmeter also including the Anemoscope and Water meter. it is made up of Sensor and Conversion-Show. The Sensor reacts to the average velocity of fluid with multi-blades rotor so as to speculating the flow value and the accumulative flow value. The velocity (or circles) of rotor can be picked up by the way of mechanism, electromagnetic induction, photo electricity, before displaying and transmitting the records by reading device.

Turbine flowmeter is a kind of speed meter, which has the advantages of high precision, good repeatability, simple structure, high pressure resistance, wide measurement range, small size, light weight, small pressure loss, long life, simple operation, convenient maintenance, etc. It is used to measure the volume flow and cumulative flow of low-viscosity, non-corrosive, clean liquids in closed pipelines. Can be widely used in petroleum, chemical, metallurgy, organic liquid, inorganic liquid, food, medicine and other industries
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%/¡À0.2%;
OUTPUT: PULSE/4-20mA;
Digital Communication:RS485, MODBUS; HART

turbine flow meter features
-Simple structure,light weight.
-High measuring precision, andgood reproducibility, sensitive response, convenient installation and maintenance
-4-20mA two-wire current output, pulse output.
-Can measure liquid, water, oil and fuel with low viscosity and no impurities

Turbine Flow Meter is a main type of Impeller Flowmeter also including the Anemoscope and Water meter.it is made up of Sensor and Conversion-Show. The Sensor reacts to the average velocity of fluid with multi-blades rotor so as to speculating the flow value and the accumulative flow value.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%;
OUTPUT: PULSE+4-20mA;
Digital Communication:RS485, MODBUS; HART

QTWG series turbine gas meters are designed to measure natural gas, LPG, air, carbon dioxide and non-corrosive gases. Turbine gas meters deliver high accuracy in gas flow measurements, with built-in volume corrector, integrated temperature and pressure measurement.

Size:DN25-400mm
Material:Aluminum alloy or stainless steel
Dual Power:3.6V battery powered+DC24V
Output:4-20mA,Pulse,RS485
Accuracy:1.5% or 1.0%

QTWG turbine gas flow meters are ideal flow measurement device for clean gas, including natural gas, LPG gas etc. Turbine gas meters are very stable measurement device which could achieve high-precision custody transfer metering, could be automatically pressure- and/or temperature-compensated.
Size:DN25-400mm
Material:Aluminum alloy or stainless steel
Dual Power:3.6V battery powered+DC24V
Output:4-20mA,Pulse,RS485
Accuracy:1.5% or 1.0%

turbine flowmeter is widely used in low flow rate and low viscosity Liquid measurement. Converting sensor signals into smart signal outputs through a microcomputer
processor design.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%;
OUTPUT: PULSE+4-20mA;
Digital Communication:RS485, MODBUS; HART

QTWG series gas turbine meters offer high quality natural gas measurement which could increase efficiency in gas transmission, distribution and industrial applications. Turbine gas meters are wIth built in temperature and pressure compensation ensure accurate measurment in standard conditions.

Size:DN25-400mm
Material:Aluminum alloy or stainless steel
Dual Power:3.6V battery powered+DC24V
Output:4-20mA,Pulse,RS485
Accuracy:1.5% or 1.0%

Liquid Turbine Flow, is the turbine flow meter that suitable for liquid flow rate measurement. Like water flow, Diesel flow. Turbine flow meter is the most popular equipment to measure flow electronically. They offer a wide flow and application rangeability. Turbine Flow Meters are easy to maintain, durable and versatile.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%;
OUTPUT: PULSE+4-20mA;
Digital Communication:RS485, MODBUS; HART

QTLL series rotary gas meters are suitable for custody transfer gas measurement of all non-corrosive gases such as natural gas, propane, butane, air, hydrogen etc. Rotary gas meters adopt high-strength aluminum alloy material which could ensure corrosion resistance and long service life.
Size:DN25-200mm
Material:Aluminum alloy or stainless steel
Dual Power:3.6V battery powered+DC24V
Output:4-20mA,Pulse,RS485
Installation: Vertical or Horizontal
Accuracy:1.5% or 1.0%

QTWG series turbine gas meters are designed to measure natural gas, air,propane and other clean gases. Turbine gas meters
provide high-quality natural gas measurement which could increase efficiency in boiler/burner control and custody transfer applications.
Size:DN25-400mm
Material:Aluminum alloy or stainless steel
Dual Power:3.6V battery powered+DC24V
Output:4-20mA,Pulse,RS485
Accuracy:1.5% or 1.0%

Sanitary turbine flow meters have stainless steel bodies and come standard with Tri-Clover fittings. Sanitary flow meter is suitable for measuring liquid without impurities. It can output pulse frequency signal. It is used to detect instantaneous flow and total integrated flow. Sanitary flow meter can be used in food, sport drink, liquor and other beverage industries, in preprocess applications.

QTWG Turbine gas meter is a popular device for gas-fired, gas pipeline network and city gas field etc. QTWG gas turbine meters are very reasonably priced with good reliability and quality. Widely used in gas measuring from Petroleum, Chemical, Electric power,Industrial boiler etc.
Size:DN25-400mm
Material:Aluminum alloy or stainless steel
Dual Power:3.6V battery powered+DC24V
Output:4-20mA,Pulse,RS485
Accuracy:1.5% or 1.0%

QTWG turbine gas flow meters are suitable for a wide range of markets, including natural gas, LPG and other gas industries. Turbine gas meter is a very stable measurement device which it could achieve high-precision custody transfer metering, the measurements can be automatically pressure and temperature compensated to obtain volumetric measurements in standard units.
Size:DN25-200mm
Material:Aluminum alloy or stainless steel
Dual Power:3.6V battery powered+DC24V
Output:4-20mA,Pulse,RS485
Installation: Vertical or Horizontal
Accuracy:1.5% or 1.0%

turbine flow meter is used for volumetric total flow and flow rate measurement & has a relatively simple working principle. As fluid flows through the turbine meter, it impinges upon turbine blades that are free to rotate about an axis along the center line of the turbine housing. The angular (rotational) velocity of the turbine rotor is directly proportional to the fluid velocity flowing through the turbine. The resulting output is taken by an electrical pickoff(s) mounted on the flow meter body.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%/¡À0.2%;
OUTPUT: PULSE/4-20mA;
Digital Communication:RS485, MODBUS; HART

turbine flow meter has advantage of precision , which can be used to measure the flow and total amount of liquid together with the corresponding flowmeter. When used together with the quantitative control instrument developed by our factory, it can carry out high precision quantitative control of liquid feeding. Widely used in petroleum, chemical, metallurgy, scientific research and other fields of measurement and control system. Turbine flow sensors equipped with sanitary joints can be used in the pharmaceutical industry.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%/¡À0.2%;
OUTPUT: PULSE/4-20mA;
Digital Communication:RS485, MODBUS; HART

turbine Flow meter for diesel is specially designed for usage in water, alcohol, diesel, gasoline and other fluid measurement and control systems. They operate according to the turbine principle, i.e. the speed of an impeller turning in the fluid flow is measured and converted into pulse or 4-20mA signals.

QTWG natural gas turbine flow meters are are ideal flow measurement device for natural gas or other non-corrosive gases applications. Turbine gas meters with wide range ratio which could achieve different flow range measurements.
Size:DN25-400mm
Material:Aluminum alloy or stainless steel
Dual Power:3.6V battery powered+DC24V
Output:4-20mA,Pulse,RS485
Accuracy:1.5% or 1.0%

QTLL series rotary gas meters a high-quality positive displacement roots-type gas meter that is available in a variety of sizes and options. Rotary gas meters are designed to meet the highest demands of reliable and accurate measurement of gas flow.
Size:DN25-200mm
Material:Aluminum alloy or stainless steel
Dual Power:3.6V battery powered+DC24V
Output:4-20mA,Pulse,RS485
Installation: Vertical or Horizontal
Accuracy:1.5% or 1.0%

turbine flow transducer adapts to measure the liquid rate and total flowrate of low viscosity. It can be widely used in the fields of Petrol, Chemical industry, Metallurgy, Scientific research for measuring or control. Several output and display methods can be selected.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%;
OUTPUT: PULSE+4-20mA;
Digital Communication:RS485, MODBUS; HART

Turbine flow meters measure the velocity of liquids, gases and cryogenic fluids. Typical fluids and gases measured with turbine flowmeters include hydrocarbons, chemicals, water, cryogenic liquids, air, natural gas and industrial gases.Apure turbine flowmeters are easy to operate and maintain. For this reason, Apure turbine flowmeters can be used worldwide and are considered a reliable, cost-effective way to achieve high-precision flow measurements
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%/¡À0.2%;
OUTPUT: PULSE/4-20mA;
Digital Communication:RS485, MODBUS; HART